Ozito ROG-191 Operating Manual

Random Orbital
Sander

230 Watt

Operation Manual
3 Year Replacement Warranty

ROG-191

To view the full range visit: www.ozito.com.au

0209

Rated Input: 230W
Rated Voltage: 230-240V ~ 50Hz
No load speed: 12,000/min
Disc size: 125mm
Paper retention: Hook & loop

Features: Dust sealed switch

Soft grip
Dust bag included

SPECIFICATIONS - MODEL NO. ROG-191

2

1. On/off switch

2. Soft grip

3. Palm grip

4. Dust bag

5. Hook and loop backing pad

1

2

4

5

3

INTRODUCTION

Warning! When using mains-powered equipment, basic safety precautions,

including the following, should always be followed to reduce risk of fire, electric
shock, personal injury and material damage.

Read and understand the manual prior to operating this tool.

Save these instructions and other documents supplied with this tool for future reference.

The electric motor has been designed for 230-240V only. Always check that the power
supply corresponds to the voltage on the rating plate.

Note: The supply of 230-240V on Ozito tools are interchangeable for Australia and
New Zealand.

This tool is double insulated in accordance with AS/NZS 60745-2-4: 2003;
therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a power tool
repairer in order to avoid a hazard.

Note: Double insulation does not take the place of normal safety precautions when
operating this tool. The insulation system is for added protection against injury
resulting from a possible electrical insulation failure within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before
use, inspect the extension lead for signs of damage, wear and ageing. Replace the
extension lead if damaged or defective. When using an extension lead on a r

eel,

always unwind the lead completely

. Use of an extension lead not suitable for the
power input of the tool or which is damaged or defective may result in a risk of fire
and electric shock.

3

SAFETY INSTRUCTIONS

ELECTRICAL SAFETY

Congratulations on purchasing an Ozito Random Orbital
Sander. We aim to provide quality tools at an affordable
price. We hope you will enjoy using this tool for many years.

Your Ozito Random Orbital Sander ROG-191 has been
designed for sanding timber, metal and plastics. It is
intended for DIY use only.

GENERAL SAFETY RULES

4

Warning! Read all instructions, Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury. The term “Power Tool” in
all of the warnings listed below refers to your mains operated (corded) power
tool or battery operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep work area clean and well lit. Cluttered and dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators.

There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts.

Damaged or entangled cords increase the risk of electric shock.

• When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.

A moment of inattention

while operating power tools may result in serious personal injury.

• Use safety equipment. Always wear eye pr

otection.

Safety equipment such
as dust mask, non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.

• Avoid accidental star

ting. Ensur

e the switch is in the of

f position befor

e

plugging in.

Carrying power tools with your finger on the switch or plugging in

power tools that have the switch on invites accidents.