Ozito PHT-410 Instruction Manual
Pole Hedge Trimmer
410mm 900W
Instruction Manual
2 Year Replacement Warranty
PHT-410
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and /or serious injury.
Save all warnings and instructions for future reference.
To view the full range visit: www.ozito.com.au
0212
!!
Motor: 900W
Input: 230-240V ~ 50Hz
No load speed: 1000/min
Blade length: 410mm
Max. blade capacity: 18mm
Weight (tool only): 6.05kgs
1. Blade
2. Gearbox
3. Blade adjustment locking knob
4. Angle Head locking mechanism
5. Upper locking lever
6. Lower locking lever
7. Blade angle adjustment handle
8. Upper shaft
9. Shaft locking knob
10. Adjustable auxiliar
y straight handle
11. Adjustable auxiliar
y D-handle
12. Lower shaft
13. Safety slide
14. Shoulder strap attachment bracket
15. Rotating handle lock
16. Lock off switch
17. On/of
f button
18. Rear handle
19. Extension cor
d restraint
20. Blade cover
21. Shoulder strap
22. Auxiliar
y handle bracket
2
SPECIFICATIONS - MODEL NO. PHT-410
3
1
6
KNOW YOUR PRODUCT
19
20
5
11
15
7
2
4
9
14
18
16
17
13
12
10
8
21
22
3
TABLE OF CONTENTS
SPECIFICATIONS ………………………………………..
INTRODUCTION…………………………………………
ELECTRICAL SAFETY…………….………………………
GENERAL SAFETY WARNINGS…………………………
HEDGE TRIMMER SAFETY WARNINGS
………………
ASSEMBLY……………………………………………
……
OPERATION………………………………………………
MAINTENANCE…………….……………………………
TROUBLE SHOOTING…………….…………………….
SPARE PARTS …………….……………………………...
DESCRIPTION OF SYMBOLS ………………………….
PACK CONTENTS ………………………………………
WARRANTY………………………………………………
Page 2
Page 4
Page 4
Page 5
Page 7
Page 8
Page 9
Page 12
Page 13
Page 13
Page 14
Page 15
Page 16
INTRODUCTION
4
Congratulations on purchasing an Ozito Pole Hedge
Trimmer. We aim to provide quality tools at an
affordable price.
We hope you will enjoy using this tool for many years.
The PHT-410 Pole Hedge Trimmer has been designed
for trimming light foliage and is intended for DIY use only.
WARNING! When using mains-powered equipment, basic safety
precautions, including the following, should always be followed to reduce
risk of fire, electric shock, personal injury and material damage.
Read and understand the manual prior to operating this tool.
Save these instructions and other documents supplied with this tool for future
reference.
The electric motor has been designed for 230V and 240V only. Always check that
the power supply corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for
Australia and New Zealand.
This tool is double insulated in accordance with AS/NZS 60745-2-15;
therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by a qualified electrician or a
power tool repairer in order to avoid a hazard.
If operating a power tool in a damp location is unavoidable use a residual current
device (RCD) protected supply Use of an RCD reduces the risk of electric shock.
Note: Double insulation does not take the place of normal safety precautions
when operating this tool. The insulation system is for added protection against
injury resulting from a possible electrical insulation failure within the tool.
Using an extension lead
Always use an approved extension lead suitable for the power input of this tool.
Before use, inspect the extension lead for signs of damage, wear and ageing.
Replace the extension lead if damaged or defective. When using an extension
lead on a reel, always unwind the lead completely. Use of an extension lead not
suitable for the power input of the tool or which is damaged or defective may
result in a risk of fire and electric shock.
ELECTRICAL SAFETY
!!
!
!
5
GENERAL POWER TOOL SAFETY WARNINGS
!!
WARNING! Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
The term “power tool" in all of the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the
influence of drugs, alcohol or medication.
A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c)
Pr
event unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the
tool.
Carrying power tools with your finger on the switch or energising power tools
that have the switch on invites accidents.
!
!
Loading...