Ozito PCS-406 Instruction Manual
PETROL
CHAINSAW
37.2cc - 406mm
INSTRUCTION MANUAL
SPECIFICATIONS
Engine: 37.2cc 2 Stroke
Output Power: 1.2kW
No Load Idling Speed: 3,200rpm
Max. No Load Speed: 11,000rpm
Bar Length: 406mm (16”)
Bar Type: Oregon
Chain Brake: Automatic
Oil Feed: Automatic Pump
Fuel Mixture: 40:1
Chain Oil: Standard Chain Bar Oil
Weight: 4.5kg
PCS-406
WHAT’S IN THE BOX
Petrol Chainsaw
Socket Wrench and
Screwdriver
Fuel/Oil Mixing Bottle
Guide Bar Cover
Chain File
1
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
KNOW YOUR PRODUCT
SETUP & PREPARATION
1 Throttle Safety Lock
2 Throttle Trigger
3 Priming Bulb
4 Choke Control
5 Chain Drive Cover
6 Chain Tension Screw
7 Chain Drive Cover Nuts
8 Guide Bar
9 Chain
10 Chain Brake
11 Bucking Spikes
12 Side Operating Handle
13 Recoil Starter
14 Carburettor Adjustment Screws
15 Filter Cover Knob
16 Filter Cover
17 Fuel Tank Cap
18 Chain Bar Oil Cap
19 On/Off Switch
1. FUEL
• Only use oil that is expressly labelled for use with air-cooled 2-stroke engines.
• Use unleaded petrol with a minimum octane rating of 89.
WARNING!: PETROL IS VERY FLAMMABLE. AVOID
SMOKING OR CAUSING ANY SPARKS OR FLAMES
NEAR FUEL. MAKE SURE THAT YOU STOP THE MOTOR
AND ALLOW IT TO COOL BEFORE REFUELLING THE
CHAINSAW. SELECT AN OPEN OUTDOOR AREA FOR
FUELLING AND MOVE AT LEAST 3M AWAY FROM THE
FUELLING POINT BEFORE STARTING THE MOTOR.
PETROL CHAINSAW
500ml
Regular
Unleaded
1. Fill with unleaded petrol up to
fuel line.
2. Add 2-stroke oil up to oil line.
3. Shake vigorously for a
thorough mix.
4. Remove YELLOW fuel tank
cap and ll the fuel tank to
about 80% of its capacity with
the fuel mix.
Fuel tank capacity: 310ml
5. Fasten the fuel tank cap and
clean any spillage.
2. CHAIN BAR OIL
3. CHAIN BRAKE & CHOKE
OPERATION
Chain brake/Anti kickback guard
The chain brake operates automatically in the event of kick back.
Kick back occurs if the chain catches on the wood being cut. In the
event of the chain catching, the chainsaw will push back suddenly,
when this happens, your hand (which is on the side handle during
operation) will naturally move forward automatically causing the guard
to be pushed forward, engaging the chain brake and stopping the
chain.
CHOKE - When the
chainsaw is cold
rst pull out the
choke control to the
CHOKE position, (fully
withdrawn).
RUN - Once the choke
control has been
pulled out, it returns
automatically when
the throttle trigger is
operated
IMPORTANT!: DO NOT PUSH THE CHOKE IN
MANUALLY. THE CHOKE WILL AUTOMATICALLY
RETURN TO RUN POSITION WHEN THE THROTTLE
SAFETY LOCK AND TRIGGER ARE PRESSED.
Automatic oil feed system
The chainsaw is equipped with an automatic
oil feed system. This delivers oil to the bar and
chain.
Run the engine at medium speed and check
that the chain splatters a thin line of oil which
can be seen on the ground/material when the
bar is pointed downwards. This may take 15-30
seconds to occur.
Please refer to maintenance section overleaf
for detailed instructions on how to adjust the
automatic oil feed system if insufcient chain
bar oil is being applied to the chain.
WARNING!: NEVER START WORK UNLESS THE CHAIN
AND BAR ARE LUBICATED
NOTE: ONLY USE OIL THAT IS EXPRESSLY LABELLED
“CHAIN BAR OIL”
START RUN
BRAKE ON BRAKE OFF
1. Remove BLACK chain
bar oil cap and ll the
tank to about 80% of
its capacity with chain
bar oil.
Chain Bar Oil Tank
Capacity: 210ml
2. Fasten the chain bar oil
cap and clean any oil
spillage.
Loading...