Ozito 25.4cc-305mm Bar, PCS-305 Instruction Manual

PETROL
CHAINSAW

25.4cc-305mm Bar

INSTRUCTION MANUAL

SPECIFICATIONS

Engine: 25.4cc 2-Stroke
Output Power: 0.9kw
No Load Idling Motor Speed: 3,500/min
Max. No Load Motor Speed: 11,000/min
Bar Length: 305mm (12”)
Bar Type: Sprocket Nose
Chain Brake: Automatic
Oil Feed: Automatic Pump
Fuel Mixture: 35:1
Chain Oil: Standard Chain Bar Oil

PCS-305

WHAT’S IN THE BOX

Petrol Chainsaw

Socket Wrench and
Screwdriver

Oil Mix Bottle

Guide Bar Cover

ozito.com.au

Chain File

1

ONLINE MANUAL

Scan this QR Code with your
mobile device to take you to
the online manual.

5. Fasten the fuel tank
cap and clean any
spillage.

KNOW YOUR PRODUCT SETUP & PREPARATION

1 Choke control
2 Exhaust
3 Chain Drive Cover
4 Throtle Safety Lock
5 Throttle Trigger

6 Chain Tension Screw
7 Chain Drive Cover Nut
8 On/Off Switch
9 Guide Bar
10 Chain

11 Chain Brake
12 Bucking Spikes
13 Fuel Tank Cap
14 Chain Bar Oil Cap
15 Priming Bulb

16 Side Operating Handle
17 Recoil Starter
18 Carburettor Adjustment Screws
19 Filter Cover
20 Filter Cover Knob

1: FUEL

• Only use oil that is expressly labelled for use with air-cooled 2-stroke engines.

• Use unleaded petrol with a minimum Octane number of 89.

2. Fill with 2-stroke oil up
to oil line.

1. Fill with unleaded petrol
up to fuel line.

WARNING!: Petrol is very ammable. Avoid smoking or

causing any sparks or ames near fuel. Make sure that
you stop the motor and allow it to cool before refuelling
the chainsaw. Select an open outdoor area for fuelling
and move at least 3m away from the fuelling point before
starting the motor.

PETROL CHAINSAW

500ml
Regular
Unleaded

Fuel tank capacity: 200ml

3. Shake vigorously and

ensure thorough mix.

4. Remove YELLOW

fuel tank cap and ll the

fuel tank to about 80%
of its capacity with the
fuel mix.

WARNING!: Never start work unless the chain and bar

are lubicated

2. CHAIN BAR OIL

3. CHAIN BRAKE & CHOKE

2. Fasten the chain bar
oil cap and clean any oil
spillage..

1. Remove BLACK chain bar oil cap and ll the tank to about
80% of its capacity with chain bar oil

• Only use oil that is expressly labeled “Chain Bar Oil”.

OPERATION

Chain brake / Anti kickback guard

The chain brake operates automatically in the event of kick
back. Kick back occurs if the chain catches on the wood being
cut. In the event of the chain catching, chainsaw will push
back suddenly, when this happens, your hand (which is on
the side handle during operation) will naturally move forward
automatically causing the guard to be pushed forward, engaging
the chain brake.

Chain bar oil tank capacity: 140ml

NOTE: For operator safety, the chain brake disengaging

action has been designed to be a rm deliberate action.

BRAKE DISENGAGED

BRAKE ENGAGED

CHOKE - When the
chainsaw is cold

rst pull out the

choke control to the
CHOKE position, (fully
withdrawn).

RUN - Once the choke
control has been
pulled out, it returns
automatically when the
throttle trigger is operated

IMPORTANT!: Do not push the choke down manually.

The choke will automatically return to run position when
the throttle safety lock and trigger are pressed.

Automatic oil feed system

The chainsaw is equiped with an
automatic oil feed system, this delivers oil
to the bar and chain.

Run the engine at medium speed and
check that the chain splatters a thin
line of oil which can be seen on the
ground/material when the bar is pointed
downwards. This may take 15-30 seconds
to occur.