Ozark Trail W418.1S Assembly Manual

ASSEMBLY INSTRUCTIONS

MODEL W418.1S SUN SHELTER 8’ X 6’

DO NOT LEAVE YOUR SHADE CANOPY SET UP IN DIRECT SUNLIGHT LONGER THAN NECESSARY. THE SUN’S
ULTRAVIOLET (UV) LIGHT DEGRADES ALMOST EVERY FABRIC AND MATERIAL. IF LEFT IN SUNLIGHT FOR
PROLONGED PERIODS OF TIME, FABRIC WILL FADE AND WEAKEN. DO NOT STORE SHADE CANOPY ON
CONCRETE FLOOR. DO NOT SPRAY THE SHADE CANOPY WITH INSECTICIDE.

EXERCISE CARE WHEN USING ELECTRIC DEVICES IN AND NEAR SHADE CANOPY.

Although our tents and canopies are constructed to rigid specifications, periods of wind or rain soaking the
ground may loosen the stakes and cause the uprights to sink into the ground. This will weaken the rigidity of the
overall structure. Water pockets may also form in the roof if the unit is not assembled taut, possibly causing
broken frames and torn fabric.

If you have questions or need to order a part, call 1-800-325-4121 or send an email to [e-mail]. Have your model
number or part number ready when you call.

DO NOT ORDER BY REFERENCE KEY NUMBER.

CARE

REPLACEMENT PARTS

Send your request for parts to:

Exxel Outdoors, LLC.
6235 Lookout Road
Boulder, CO 80301

SAFETY WARNING ­DOs AND DO NOTs

EVERYONE WHO USES THIS SHADE CANOPY SHOULD READ THIS MANUAL AND BECOME FAMILIAR

WITH ALL SAFETY WARNINGS AND PRECAUTIONS FOR SAFE USE, ASSEMBLY, CARE,

MAINTENANCE, AND STORAGE. KEEP THIS MANUAL SO YOU CAN REFER TO IT LATER.

WARNING

FLAMMABILITY WARNING KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS SHADE CANOPY FABRIC
This shade canopy is made with flame resistant fabric which meets CPAI-84 specification. IT IS NOT FIREPROOF. The fabric will burn if left in continuous
contact with any flame source. The application of any foreign substance to the shade canopy fabric may render the flame-resistant properties ineffective.
For these reasons:

• DO NOT use matches, lighters, stoves, heaters, grills, lanterns, candles, cooking equipment, or other fuel-burning devices inside or
near a shade canopy.

• DO NOT build fires inside or near a shade canopy.

• DO NOT leave campfires unattended.
Your failure to follow this warning will cause death, serious injury, or permanent disability to you or others.

PROTECT YOUR CHILDREN
Children will not understand and appreciate safety warnings, and will not know how to avoid or respond to these hazards if no adults are present.
For these reasons:

• DO NOT leave children unattended inside a shade canopy or in camp.

• DO NOT allow children to assemble a shade canopy.

• DO NOT allow children to enter or exit a shade canopy except through the door.
Your failure to follow this warning will cause death, serious injury, or permanent disability to your children.

MODEL NO. W418.1S 8' X 6'

DESCRIPTION PART NO.

KEY
NO.

QTY
REQ

Main Pole

Complete Frame

Sand Bags

Steel Stakes

W418.1AM

W418.1AST

W418.1SB

PIN STAKE

2

1

4

4

A

A

A

ASSEMBLY INSTRUCTIONS

MODEL W418.1S SUN SHELTER 8’ X 6’

NOTE: T

o take down the canopy, follow steps above in the reverse

order. Place stakes into stake bag and poles into pole bag, which

are provided. The Canopy should be folded into equal parts toward

the center to distribute the bulk. Start a small tight roll, the width of

your carry bag. Once rolled, tie a string or rope around canopy to

hold it in place. Place canopy and stake bag into carry bag.

MAKE SURE IT IS CLEAN AND DRY BEFORE STORING.

Canopy should appear as shown.

STEP 7: Stake down canopy by inserting stakes through the

webbing

loop at each corner of the canopy. Hammer stakes into ground at a

45° angle, by using a hammer or mallet.

Make sure to use strap to pull canopy

out even and tight. Sandbags are

provided for use at the beach. Fill

the bags with sand to hold the canopy

in place.

STEP 6:

Where the poles cross there

are fabric ties, tie them around both

poles to hold them together.

STEP 5: Clip the plastic hooks attached

to the canopy walls to the poles.

STEP 4: Starting at the back corners of the shelter,

place ends of the fiberglass frame pole that runs

across the front of the canopy roof into the fast feet

located at the back of the canopy, by gently flexing

the pole upward into an arch. Repeat the same

procedure at the front corners of the canopy with

the pole that runs across the back of the canopy roof.

STEP 3: Slide each fiberglass pole (A) through the sleeves on the

top of the canopy roof. Position poles so that equal pole lengths

extend on either side of pole sleeves.

STEP 2: Extend the fiberglass frame poles by pulling out each

section and placing it into the metal connectors. You will have

two fiberglass poles (A).

STEP 1: Spread canopy out flat with the pole sleeves up.

IMPORTANT: WE ADVISE YOU TO ASSEMBLE THE SHADE

CANOPY ONCE BEFORE USE TO BECOME FAMILIAR WITH
THE ASSEMBLY
NOTE: PLEASE LOOK AT THE REPLACEMENT PARTS DIAGRAM
TO SEE HOW YOUR FRAME IS ASSEMBLED.