190mm Main Blade
Instruction Manual
Chapter 1, Specifications
VERY IMPORTANT NOTE:
- Visit the Oxy Heli web site www.oxyheli.com to download the latest version of the manual.
- Inside Box 2 you will find your serial number card. Please take a moment to visit the Oxy Heli web site and follow the
instructions to register your helicopter and serial number.
- It is important you take few minutes to register your helicopter and serial number with us. This is the only way to be in contact
with us to receive news, promotional information and technical tips.
- We will also choose five serial numbers each year that will win a discount coupon worth 200USD each to spend at the Oxy Heli
or Lynx Heli web sites.
- Thank you for your purchase, and we wish you the best enjoyment with your new Oxy 2 Helicopter.
Chapter 1 - Specifications
Chapter 2 - Important Notes
Chapter 3 - Required Tools for Assembly
Chapter 4 - What's Inside The Box
Chapter 5 - Pinion Selection & RPM
Chapter 6 - Tail Assembly
Chapter 7 - Main Frame Assembly
Chapter 8 - Align and Lock Frame Panel
Chapter 9 - Transmission Assembly
Chapter 10 - Belt Tension & Adjustment
Chapter 11 - Main Rotor Assembly
Chapter 12 - ESC Installation
page 2
INDEX
page 3
page 4
page 5 - 6
page 7
page 8 - 13
page 14 - 18
page 19
page 20-21
page 22
page 23-25
page 26
SPECIFICATIONS
435mm
Chapter 13 - Flybarless Installation
Chapter 14 - Servo & Servo Rod Prepareration
Chapter 15 - Cylic Servo Installation
Chapter 16 - Tail Servo Installation
Chapter 17 - Landing Gear & Battery Installation
Chapter 18 - Main & Tail Blades Installation
Chapter 19 - Adjustment Servo with Leveler
Chapter 20 - Exploded View
page 27
page 28
page 29
page 30
page 31
page 31
page 32-33
page 34-37
102mm
108mm
138mm
70
-Standard main rotor diameter
-Standard main blade length
-Main Grip Clamping
-Standard tail rotor diameter
-Standard tail blade length
-Tail Blade Clamping
-Weight
-Maximum motor size
-Maximum battery size
-Recommend battery
415mm
: 435mm (with 190mm blades).
: 190mm
: M2 / 3.2 mm root.
: 102-108mm.
: 38 - 41mm.
: M1.6 / 3 mm root.
: 274g (ready to fly excluding batteries)
: diameter 26mm.
: l
ength 72mm, height 25mm, width 35mm, weight 114gr
: 850 45C -1000 mAh 3s 40C max size.....
page 2
Chapter 2, Important Notes
IMPORTANT NOTE:
This model helicopter has been designed and produced to be a high performance 3D machine. With its simple design and low
parts count, pilots of all skill levels will appreciate its easy repairability. This is not a toy. Please take care assembling the model,
and take care and responsibility when you fly it. We take no responsibility for any damage or injuries, either direct or consequential,
from the use of this product. If you are not experienced in the assembly and flying of a high performance model helicopter we
recommend you seek the assistance of an experienced pilot. Above all, fly safely and we hope you enjoy this model.
SAFETY GUIDELINES:
Only fly this model in areas designated for the use of model aircraft. Ensure you obtain indemnity insurance, normally available
through your National model aircraft association. Remain at least 6 meters (20 feet) from the model at all times. Never allow
spectators or animals any closer than 30 meters (100 feet) from the model.
NOTES FOR ASSEMBLY:
Please read this instruction manual fully before beginning assembly of this model helicopter. Be sure to use quality tools during
the assembly process, and remember not to overtighten small fasteners. Note the following symbols which are used in this manual.
Use thread lock sparingly where indicated. If you are unsure about an assembly step, please seek the advice of an experienced
pilot. Warranty on any parts is only applicable prior to assembly of the part on the model.
NONE OF THE PRE ASSEMBLED PARTS HAVE THREAD LOCK ON THE SCREWS. IS IMPORTANT TO READ AND FOLLOW THE ASSEMBLY
NOTES IN EACH STEP. INCORRECT ASSEMBLY OR NOT USING THREAD LOCK WILL CAUSE A CRASH OR INJURY.
Important note
Use CA Glue
Use Loctite 243 Medium Strength
Use Loctite 648 Bonding
page 3
Use Silicone Grease
TOOLS REQUIRED
Chapter 3, Required Tools for assembly
Small Tip - Flat Screw Driver
1.3mm Hex Screw Driver
(High quality)
1.5mm Hex Screw Driver
(High quality)
Two Tools Required
Philips head screw driver
Needle nose pliers
Caliper
Uniball Pliers
page 4
INSIDE THE MAIN BOX
Canopy,
BOX 1-1,
Box 1/Bag 11 Main Frame Set,
Box 1/Bag 10 Landing Gear Set,
Tail Set Asembly Parts.
Chapter 4: What's inside the box
Box 3/Bag 1 Tail Boom Set,
Box 3/Bag 2 190mm CP Main Blade
MAIN BOX
Serial Number Card,
Box 2/Bag 1 Boom Clamp Set,
Box 2/Bag 2 Battery Tray Set,
Box 2/Bag 3 Main Gear Set,
Box 2/Bag 4 Accessories,
Box 2/ Bag 5 Extra Hardware,
page 5
INSIDE THE BOX 1
Chapter 4: What's inside the box
Canopy
Head Set Assembly Parts
Frame Set Assembly Parts
Box 1/Bag 10
Landing Gear Set
Tail Set Asembly Parts
BOX 1
Box 1/Bag 11
Main Frame Set
page 6
Chapter 5: Pinion Selection & RPM
OXY 2 POWER SYSTEM AND HEAD SPEED SET-UP
In order to choose the best setup for your Oxy 2, and optimize performance, it is important to know some basic information:
1- Motor Kv – Min 3600 - Max 6000 - See your motor specification
2- Battery Pack – (3s or 4s)
3- Your target head speed
If you use a head speed calculator, use
The kit comes with one pinions (12T-2mm Shaft ) which enables a wide head speed range with 3s batteries and 5500Kv Motor perfect for novice
and expert pilots.
Oxy 2 Fly Style / Head Speed / Main Blade / Tail Blade / Max Pitch suggestion chart:
110T
for the main gear and one of the available pinions 10T – 11T – 12T – 13T – 14T – 16T – 18T .
Oxy 2 Gear Ratio Chart
Head Speed Note:
compromise btw performances and efficiency.
Configuration examples
Since the Oxy2 is a high performance 3D RC helicopter, we suggest using high quality power components including motor, battery and
ESC. Remember the Oxy 2 is a 200 class heli – use light components to maximize flight time and performance.
Here are some suggestions:
Motor: Suggested KV 3600KV to 6000KV, 16-11 to 19-12 caliber series (stator diameter – stator length).
-
Battery: 3 or 4S with capacity from 800 to 1000mAh / 45C discharge rate. Maximum size: length 72mm, height 25mm, width
-
35mm, weight 114g.
ESC: 25 to 30A – with BEC 5V or higher.
-
Cyclic servos: Standard Sub MICRO size servo speed: =>0.06 sec/60 at 6V.
-
Rudder servo: Standard MICRO size servo – speed =>0.06 sec/60 at 6V – a specific rudder servo is suggested for best tail
-
authority.
FBL system: The Oxy 2 was designed around the U-Ikon / U-Brain and Neo V-Bar Systems. But many other smaller size FBL systems
-
can be used, depending on your personal choice. Max inner Frame dimension 26mm.
Main blade: The Oxy 2 can fly with plastic or CF main blades from 190 to 210mm. Our testing was with Lynx 190mm Carbon Plastic main
-
blades, and Zeal 210mm main blades. The Oxy 2 main grips use M2 clamp screw and have a 3.2 mm root.
Tail blades: The Oxy 2 uses our own OEM tail blades, either 38 or 41mm (included with the kit). They use a M1.6 clamp screw and
-
3 root.
We offer 38 and 41mm tail blades to suit different head speeds. Use 41mm tail blades when your head speed is lower than
4500rpm and 38mm with higher head speeds.
page 7
Although Oxy 2 can handle very high Head Speed, we suggest not to exceed 5500 RPM to maintain a good
Chapter 6: Tail Assembly
Vertical Fin Assembly
(Box 1/Bag 1)
OXY0516 - Tensioner Spacer
2 x SMR682Z-ZZ-
2.5X6X2.6 Radial Bearing
OXY0524-
2.55x4.5x0.1 Shim
OXY0279-Vertical Fin
Bearing Bushing
OXY0257-Vertical Fin
Tail Case Assembly
(Box 1/Bag 2)
OXY0515Tensioner Bushing
2 x MR52-W2
2X5X2 Radial Bearing
OXY0527-
2x3.5x0.1 Shim
Important Note:
This part, for tuning reasons,
comes factory pre assembled,
it ready to use
OXY0543-Al Tail Case
Important Note:
This part, for tuning reasons,
comes factory pre assembled,
it ready to use
Tail Rotor Assembly
(Box 1/Bag 3)
2 x SMR682Z-ZZ-
2.5X6X2.6 Radial Bearing
OXY0524-2.55x4.5x0.1 Shim
Important Note:
This part, for tuning reasons,
comes factory pre assembled,
it ready to use
OXY0521-Linkage Ball
2 x SMR682-ZZ2X5X2.3 Radial Bearing
OXY0524-
2.55x4.5x0.1 Shim
OXY0253-Tail Hub
Important Note:
This part, for tuning reasons,
comes factory pre assembled,
it ready to use
page 8
2 x OXY0551-1.5x2.8 H0.4 Washer
Important Note:
This part comes pre assembled
WITHOUT thread lock. It MUST be
re-assembled with thread lock as shown.
2 x M1.4x3 Pan Head Screw
Tail Shaft Assembly
(Box 1/Bag 4)
Chapter 6:Tail Assembly
Important Note:
This part, for tuning reasons,
comes factory pre assembled,
it ready to use.
Tail Pitch Slider Assembly
(Box 1/Bag 5)
OXY0541 - Tail Pitch
Slider Ring
2 x MR683-3x7x2
Radial Bearing
OXY0457 - Tail Pitch
Slider Bushing
Important Note:
This part, for tuning reasons,
comes factory pre assembled,
it ready to use.
OXY0255 - Tail pitch
Slider Haft Moon
Tail Shaft 16T
2 x M1.4x4
Pan Head Screw
Important Note:
This part comes pre assembled,
WITHOUT THREAD lock. Follow
the instruction for final assembly.
Do not over tighten
Pan Head Screw 2XM1.4x4
2 x OXY0522Link Control
2 x OXY0523-Link
Control Bushing
Tail Belt Crank Assembly
(Box 1/Bag 6)
Important Note:
This part, for tuning reasons,
comes factory pre assembled,
it ready to use.
page 9
2 x OXY0460 Bell Crank Bushing
2 x MR52-W22X5X2 Radial Bearing
2 x OXY0448 - Bell Crank
Pin Screw
OXY0252 - Al Tail
Bell Carnk
Carbon Fiber Tail Push Rod Assembly
(Box 3/Bag 1)
REF 1mm
Chapter 6: Tail Assembly
OXY0519-Threaded
Rod M1.4X7mm
OXY0584-STD Tail Push Rod
Important Note:
This part, for tuning reasons,
comes factory pre assembly,
it ready to use.
Tail Push Rod Guide Assembly
Step 1:
2 x OXY0539Pin Screw
OXY0067
Guide Push Rod
Push the part inside the
boom sockets as shown.
(Box 3/Bag 1)
Note: to install this
pin screw rotate
counter clock wire.
Step 3:
OXY0536-Al Tail Push
Rod Terminal
Step 2:
Note Pin Screw Thread:
Oxy designed the Pin Screw with
a counter clockwise thread. This
will help on the final locking
operation. Be careful to follow our
instructions to get a perfect assembly.
Step 4:
Slide the parts as shown
OXY0526-Plastic
Linkage Ball 3mm
Note: Install the Pin Screw
and leavea gap as shown.
REF >= 1.3mm
OXY0578 - Tail Boom STD
Important Note:
This part, for tuning reasons,
comes factory pre assembly,
it ready to use.
page 10
Step 5:
In order to lock the tail push rod
support, use a Flat Screw Driver
and turn clockwise. Do not
over tighten.
Tail Assembly Step 1
Tail Assembly Step 2
B305MXL-Timing Belt
(Box 1/Bag 8)
OXY0258-Tail
Case Center
Tail Boom Pre Assembly
Tail Case Assembly
2 x M1.6X5 Hex
Cap Screw
Chapter 6: Tail Assembly
2 x M1.6X5 Hex
Cap Screw
Belt Tensioner
Pre Assembly
4 x M1.6 x5 Hex
Cap Screw
M2 x12 Hex
Cap Screw
Tail Assembly Step 3
A
OXY0540 Tail Case Rod
Tail Shaft Pre Assembly
before install
read carefully fine
adjustment shims note.
4
A
any
shim
Smaller ID
Vertical Fin side.
Set Screw M3x3
4
Note: all screws in this step
need add loctite during assembly.
Fine Adjust Shims Note :
In order to give fine adjustment options,
in the Extra Hardware Bag you will find
extra shims 2.55X4.5X0.1.
Start assembly WITHOUT any
shims. If Tail Shaft has sideways play
more than 0.2mm,
add shims as required, to one side, as shown.
PRO TIPS: For best Tail performances little
side play is recommended.
page 11
Note: Line up the
holes, so the set
screw seats correctly
into tail shaft lock hole.
1 x Set Screw M3x3
Tail Assembly Step 4
Chapter 6: Tail Assembly
M1.6x10 Hex Cap Screw,
do not over tighten the Screw
Important Note:
Once assembly finish, check if the system can slide
and move without friction.
If tail system is assembled correctly, it should move
smoothly. In case of friction or extra play,
recheck each single component and re-assembly as
required.
2 x OXY0535-AL
Tail Servo Mout
(Box 1/Bag 9)
Note: don't install any screw
TAIL BELT ASSEMBLY AND DIRECTION CHEK:
In order to check correct belt install,
move belt position A CW and
the position B must rotate CW.
B A
Before go forward on Tail Assembly check carefully
if Belt is installed per need.
Belt MUST move without any friction.
page 12
Tail Assembly Step 5
Step 5-1:
Tail belt is showed straight coming out,
form tail boom. Be careful to
check the belt if not twisted inside the boom.
Use a flashlight to check inside the boom, for better vision.
Rotate the belt 90 degrees CCW as shown.
Step 5-2:
Hold carefully Tail Belt as showed and insert
Front Boom Insert.
Chapter 6: Tail Assembly
90
CCW Rotation.
Step 5-3:
Final Tail Belt Direction Check:
Pull Tail Belt (as shown) and check the tail hub rotates
in the direction shown. If the Tail Rotor rotates
in the wrong direction, go back to the previous
instructions and double check your assembly.
OXY0450-Front
Boom Insert
(Box 1/Bag 8)
Press in this insert parts into
Tail Boom to help Tail Belt
doesn't twist in the next
installation step
Pull Tail Belt here
page 13
Boom Clamp Assembly
(Box 2/Bag 1)
Pulley Guide Belt Assembly
Install the Pins into the Pulley
Guides and press completely into
the Tail Boom Clamp Socket Lips.
OXY0242-Pulley
Guide Belt
2 x Pulley Guide Belt Assembly
Chapter 7: Main Frame Assembly
2 x MR52-W2-2X5X2
Radial Bearing
OXY0532-
1.6X13.8 Pin
2 x OXY0460 - Bell
Crank Bushing
Important Note:
this part, for tuning reasons,
comes factory pre assembled,
it ready to use
2 x OXY0452Boom Clamp
Upper Main Shaft
Bearing Block Assembly
(Box 1-1/Bag 1)
OXY0235-Upper Main
Shaft Breaing Block
Important Note:
The Radials Bearing come
factory pre assembled with
Loctite. It is ready to use.
MR6700 ZZC-10X15W4
Radial Bearing
4 x OXY0453 - Boom
Lock Rod
Lower Main Shaft
Bearing Block Assembly
(Box 1-1/Bag 2)
Important Note:
The Radials Bearing come
factory pre assembled with
Loctite. It is ready to use.
MR6700 ZZC-10X15W4
Radial Bearing
OXY0236-Lower Main
Shaft Breaing Block
page 14
Canopy Mount Assembly
(Box 1-1/Bag 3)
Chapter 7: Main Frame Assembly
Left Canopy
Mount Assembly
OXY0461 - Break
Away Canopy support
mount
M1.6x4 Hex
Cap Screw
Motor Pinion Installaion
Note: Output Motor Shaft
prepareration:
because OXY2 pinion have bonding
assembly follow below step for best results.
1- Sand Paper output shaft.
2- Use bonding compound
(Loctite 648 or Lynx LX5648).
Don't use STD lock thread.
3- After Install wait at least 10h before fly.
Output Shaft
to prepare
OXY0260Canopy Mount
Right Canopy
Mount Assembly
Kit Pionion
11T ID
2mm
(Box 1-1/Bag 4)
Position A
Important Note:
Install Canopy Pin into
Position A as shown
REF 11mm
Motor Installation
OXY2 support two size of motor fitting
(13mm/M2 and 19mm/M2.5),
choose the correct holes
dependig on the used Motor.
Use Hex Cap Screw M2x5 for 13mm holes
Use Button Head Screw M2.5x5 for 19mm holes
13mm
19mm
2mm
2.50mm
Use bonding compound
loctite 648 or LX5648,
don't use standard loctite
after install wait
until 10h before fly
OXY0238Motor Mount
(Box 1-1/Bag 4)
page 15
Main Frame Asembly Step 1
Chapter 7: Main Frame Asembly
OXY0263-Main Frame
Box 1/Bag 11
OXY2 support two kind of Servo dimension options.
Lower Bearing Block can be installed in two Frame position.
Follow note for Servo type A or B install.
Main Frame Asembly Step 1
B
A
Left Canopy Assembly
Box 1-1/Bag 11
A
B
Max 10mm
Servo type A
use Frame holes A position
4 x M1.6x5
Hex Cap Screw
26.5mm
23.6mm
Max 10mm
Servo type B
use Frame holes B position
4 x M1.6x5 Hex Cap Screw
Note: Don't fully tighten yet
see assembly alignment Step
page 19.
Upper Main Shaft
Bearing Block Assembly
Box 1-1/Bag 9
Lower Main Shaft
Bearing Block Assembly
Box 1-1/Bag 10
OXY0300- Battery Tray
Box 2/Bag 2
page 16
3 x M2x6 Self Tapping Screw
Note: Don't use any loctite
3 x M2x6
Self Tapping Screw
OXY0263-Main Frame
Main Frame Assembly Step 2
Boom Clamp Assembly
Chapter 7: Main Frame Assembly
Motor Asembly
Main Frame Assembly Step 3
6 x M2x6
Hex Cap Screw
OXY0081-
2.1X5.5X1 Washer
6 x M2x6 Hex Cap Screw
Note: Don't fully tighten yet.
Wait future neccessary
assembly step.
Right Canopy Mount
Assembly.
4 x M1.6x5
Hex Cap Screw
4 x M1.6x5 Hex Cap Screw
Note: Don't fully tighten yet.
See assembly alignment
Step page 16.
3 x M2x6 Self tapping Screw
Note: Don't use any loctite
3 x M2x6 Self
Tapping Screw
page 17
Main Frame Asembly Step 4
6 x M2x6
Hex Cap Screw
6 x M2x6 Hex Cap Screw
Note: Don't fully tighten yet.
Wait future neccessary
assembly step.
Main Frame Asembly Step 5
Chapter 7: Main Frame Asembly
2 x OXY0081-
2.1X5.5X1 Washer
2 x M1.6x5
Hex Cap Screw
2 x M1.6x5 Hex Cap Screw
OXY0251 - Anti
Rotation Guide
Box 1-1/Bag 11
page 18
90°
Chapter 8: Main Frame Alignment
OXY0459-Main Shaft
(Box 1-1/Bag 8)
Install main shaft with frame assembly
on a flat surface, push down on both frames
together and then fully tighten all M1.6x5 hex cap
screws (x8) holding the bearing blocks.
90°
Flat Surface
page 19
Tail System And Main Gear Installation
Chapter 9: Transmission Assembly
Insert Tail
Assembly as shown
Before next assembly step check carefully
Tail Belt assembly position as shown.
OXY2 support two kind of
servo dimension, use specific
main gear bushing spacer
for Servo type B.
OXY2 Tail Assembly
OXY0247 - Main
Gear Bushing
Main Gear 110T-55T pulley
Assembly
page 20
(Box 2/Bag 3)
Important Note:
The Main Gear come
factory pre assembled.
It is ready to use.
23.60
Servo Type B
Chapter 9: Transmission Assembly
Note: hole's position on main shaft are symmetrical.
A A
M2x8 Hex
Cap Screw
don't over tighten
M2x8 Hex
Cap Screw
Main Gear
Assembly
In order to check the belt installation, we
recommend to follow two simple steps:
1- Check with light, look inside the boom
from the tail case and check the belt is
only twisted 90 degrees.
2- Rotate the main gear in the flight direction
(as shown) and check the tail hub rotates
in the direction shown. If the Tail Rotor rotates
in the wrong direction, go back to previous
instructions and double check your assembly.
page 21
Main Shaft Collar and Tail Belt tensioning.
Chapter 10: Belt Tension & Adjustment
M1.6x5-Hex
Cap Screw
don't over tighten
Pull up Main Shaft
OXY0451-Main
Shaft Collar
Push down Main
Shaft Collar
Tail Belt Pulley Note:
Before tensioning Tail Belt, check
if correctly positioned in
both Belt Pulleys.
8 x M2x6 Hex Cap Screw
- Be sure the boom is assembled and installed correctly.
- Loosen the tail boom by loosening the eight M2x6 Hex Cap Screws.
- Adjust the Belt tension by pulling on the Tail Boom.
- Tighten the eight M2x6 Hex Cap Screws.
- The belt must have good tension. We suggest re-checking after a few
flights. We suggest to check belt tension often, before each flying session.
- If spool up get difficult, may Tail Belt is over tight,
recheck and eventually loose Belt tension little bit
- If the belt is often loose, you should check the lock system or belt integrity.
- Tests show that a hard 3D pilot can perform over 400 flights before the belt
will fail. We recommend replacing the Tail Belt after 300 flights, even if it
does not show wear, to avoid it breaking unexpectedly in flight.
- After a crash, spend some time checking Belt integrity and replace if any
teeth are missing.
Use a Screw Driver to check
Belt Tension (suggested max
deflection is 1mm)
- Note: We recommend a tight
Belt tension.
- If spool up get difficult, may Tail Belt
is over tight, recheck and eventually
loose Belt tension little bit
- Check the Belt tension again
after the first 2 flights.
- With a new Tail Belt, when the
head is rotated slowly, it is normal
to hear a tooth sound as the belt
engages with the Main Pulley. This
sound is normal and will disappear
after a few flights and the necessary
"break-in".
page 22
Main Grip Assembly
(Box 1-1/Bag 5)
Chapter 11: Main Rotor Assembly
2.70
OXY0228-Main Grip
DFC Arm Assembly
(Box 1-1/Bag 5)
F2.5-6GC-2.5x6x3
Thrust Bearing
OXY0519-M1.4 x7
Threaded Rod
2 x SMR682X_ZZC_3
2.5x6x2.6 Radial Bearing
add silicon
grease
REF 24.5 mm
2.50
Important Note:
This part, for tuning reasons,
comes factory pre assembled
with grease and loctite. It is
ready to use.
OXY0526-Plastic
Linkage Ball 3mm
Main Rotor Assembly
(Box 1-1/Bag 5)
OXY0227 - Center Hub
Important Note:
This part comes pre assembled
WITHOUT thread lock. Follow
the instruction for final assembly.
OXY0529 - DFC Arm
OXY0446 Spindle Shaft
OXY0229 Dampener Bushing
O'ring 3W1.5
Important Note:
This part, for tuning reasons,
comes factory pre assembled.
Step faced to Main Grip
OXY0524-
2.55X4.5X0.1 Shim
See Fine Adjust Shims Note.
OXY0528 Damperner Spacer
A
Fine Adjust Shims:
In order to give fine adjustment options,
the extra Hardware Bag contains extra
Shims 2.55x4.5x0.1. Start assembly with one (each side)
pre installed shim. If the Main Grips have
sideway play, add shims as required.
Each Grips must have the same number
of shims. If you add one shim on the left
side, you need to also add one shim on
the right side.
page 23
OXY0525-
1.6X3.5X0.5 Washer
2x M1.6x5
Hex Cap Screw
Main Rotor Assembly
(Box 1-1/Bag 5)
Chapter 11: Main Rotor Assembly
OXY0447 DFC Pin Screw
DFC Arm
Swash Plate Assembly
(Box 1-1/Bag 6)
OXY0530 2X4X4.4 Bushing
Flat surface
DFC Arm are not symmetrical.
Flat surface faced to Screw.
Step faced to Main Grip.
Important Note:
This part comes pre assembled
WITHOUT thread lock. Follow
the instruction for final assembly.
Once you finish assembly, ensure the DFC
Arms can rotate without friction. If the DFC
Arms are assembled correctly, rotation
should be smooth and without friction. In
case of any friction, recheck each
component and re-assembly as necessary.
OXY0020-M1.2x2
Special Screw
Center Ball
Stepped surface
5 x OXY0521-Linkage
ball 3x1.5mm
OXY0454-Anti
Rotation Pin
Lower and Upper
Swash Plate
Important Note:
this part, for tuning reasions,
comes factory pre assembled,
it ready to use.
Important Note:
This part comes pre assembled WITHOUT
thread lock. Follow the instruction for final
assembly.
Swivel Ball Note:
The Swivel Ball is pre-assembled with a
precise fitting. When new, the Swash Plate
center ball will have a little friction. After a
few flights and “break-in” it will come smooth,
keeping the best precision without play.
page 24
Main Rotor Assembly step 1
Chapter 11: Main Rotor Assembly
Head Assembly
Swash Plate
Assembly
Main Rotor Assembly step 2
All Screw in this step
need add loctite,
don't over tighten.
2 x M1.6x6 Hex
Cap Screw
M2x8 Hex
Cap Screw
page 25
Chapter 12: ESC Installation
ESC
Double - side Tape
(Box 2/Bag 4)
use your choice of
connector rated
Battery wires
Be carefully Motor wire
and ESC will not touch
Motor/Pinion.
2 x Cable Tie
Motor wires
Use 3 x cable ties, to secure the Throttle ESC wire to the main frame. Use the Frame
built-in socket for best holding. In this Step connect the Motor and ESC Wires but don't
secure yet. Wait till the final motor rotation check, once the FBL system is set up.
NOTE: To reverse Motor rotation direction , just switch 2 of the 3 wires.
CF may have sharp edges:
file accurately where wiring
pass by, and/or protect
wiring adequately.
page 26
Chapter 13: Flybarless Installation
The FBL system can be
installed at the bottom or
top of the boom clamp.
We suggest to use the
bottom for easy wiring
and servo removal.
Flybarless Unit
Position 1
For extra FBL support we
suggest to add Electronic
Hook and Loop as shown.
Double - Side Tape
(Box 2/Bag 4)
Flybarless Unit
Position 2
page 27
Chapter 14: Servo & Servo Rod Prepareration
- You should now do some initial setup of your FBL unit and servos.
- We recommend you select a new model in your transmitter, and reset your FBL unit and start with a clean setup in it as well.
- After binding your transmitter to the receiver system used with the FBL unit, work your way through the FBL setup instructions to the point
you plug in your servos.
- Now set your collective stick in the middle position, and position the servo arms as close to the correct positions you can on each servo
see the following pages for arm orientations on the various servos.
- Next confirm the servos work in the correct direction, then return the collective stick to the center position.
- Now use your FBL unit to trim the servos so the arms are exactly horizontal (see pictures below).
- This procedure varies between units. Carefully label the position of the servos, then proceed with the installation of the servos as shown.
Cyclic Servo.
Cut here
Ref 7 mm
(Linkage Ball Position)
Cut here
Ref 7mm
(Linkage Ball Position)
Linkage Ball Direction: cyclic servo
Linkage Ball, must installed as shown.
Reuse STD
Servo Arm
Reuse STD
Servo Screw
Linkage Ball Direction: The Tail servo
Linkage Ball must be installed as shown.
Reuse STD
Servo Arm
OXY0521-Linkage
ball 3x1.5mm
(Box 1-1/Bag 7)
Arm position with zero deg pitch
and centered cyclic stick.
Positive
90°
Pitch
Negative
Pitch
Arm position with zero deg pitch
and centered rudder stick.
Nose Right
Nose Left
90°
Servo Rod Assembled
(Box 1-1/Bag 7)
OXY0520-M1.4X11
Threaded Rod
OXY0521-Linkage
ball 3x1.5mm
(Box 1-1/Bag 7)
OXY0526-Plastic
Linkage Ball 3mm
Reuse STD
Servo Screw
REF 5 mm
Servo Rod Refference
for Servo type A
REF 4 mm
Servo Rod Refference
for Servo type B
It is really important the servo rods screw onto
the linkages the same amount. The Plastic
ball links have a Lynx logo to give you
information about turn adjustment, but have
a symmetrical ball socket shape and can be
installed in either direction to achieve the
best fine tuning.
page 28
Chapter 15: Cylic Servo Installation
6 x TCEM1.6x5 Hex Cap Screw
6 x TCEM1.6x5
Hex Cap Screw
6 x OXY0525-
1.6X3.5X0.5 Washer
3 x Servo Rod Assembly
page 29
Servo Layout
Chapter 16: Tail Servo Installation
4 x M1.6x5 - Hex
Cap Screw
2 x OXY0525-
1.6X3.5X0.5 Washer
Tail Push Rod Assembly
(Box 3/Bag 1)
4 x M1.6x5 - Hex Cap Screw
ref 7.2
Nose Right
90°
Nose Left
Bottom Heli View
Arm position with
centered Rudder stick.
Maximun Tail Servo Size Note:
Max 12mm
OXY0552 - Leveler
(Box 2/Bag 4)
page 30
Top Heli View
3.5
With Rudder Stick centered
and the Tail Servo Arm in the
center position, adjust the
Tail Push Rod length until the
Tail Bell Crank and Tail Case
Plate are parallel as shown.
The Oxy 2 Tail System has
approximately 3.5 of counter
torque with the Tail Bell Crank
set per instructions.
Landing Gear & Battery Installtion
Chapter 17: Landing Gear & Battery Installtion
Electronic Hook & Loop
(Box 2/Bag 4)
OXY0242-Right
Landing Gear
(Box 1/Bag 10)
OXY0237-Bottom
Landing Gear
(Box 1/Bag 10)
Satellite
EX
Important Note: Use both double sided Hook
and Loop Velcro and the included battery
straps to fully secure the battery pack.
4x M2x8 Self Tapping Screw
don't over tighten
4x M2x8
Self Tapping Screw
OXY0241-Left
Landing Gear
(Box 1/Bag 10)
Main Blades Installation
M2x10 Button
Head Screw
190 mm Carbon
Plastic Main Blade
(Box 3/Bag 2)
Note: The Oxy Main Grips have a 3.2mm root cavity
in order to work with any standard 190 / 210 main
blade root.
Tail Blades Installation
Plastic Tail Blade
38 or 41mm
(Box 1/Bag 7)
M1.6x8 Hex
Cup Screw
Oxy tail blade dimension note: In order to assure
the best performance Oxy made a custom tail
blade with a 3mm root. If you use different tail
blades with a 2.5mm root you must use shims (not
included).
Information about 38 and 41mm tail blades: In the
kit we include two sets of tail blades - the 38mm are
designed for high head speed, the 41mm are designed
for low head speed. We recommends using 38mm
when head speed is higher than 4000rpm.
page 31
Chapter 19: Adjustment Servo With Leveler
Before Fly:
Now complete the setup of your FBL system. In the Accessories Bag you will find an Oxy 3 Swash Plate Leveler.
This Tool is designed to fit under the Swash Plate without disassembly any parts. This simple tool will both level the swash and give
the Zero Pitch Position.
Starting gyro gain: The Oxy 2 was designed around famous FBL Systems (IKON / Brain / mini V-Bar), and we suggest you start with
the following standard set up and adjust after test flying.
Cyclic Set Up:
Use suggested settings for 450 Helicopters and adjust after test flights.
See our table on page 15 for RPM and Pitch Settings. Cyclic Max pitch should be +/- 10.5 deg.
Tail Set Up:
Use the suggested settings for 450 Helicopters BUT start with a lower Tail Gain
IKON / Brain = 20%
Mini V-Bar = 250 Heli suggested gain.
Lift up swash plate
as shown to have
space for inserting Leveler.
OXY0552 - Leveler
(Box 2/Bag 4)
Rotate Leveler as shown
Lift Swash Plate down
untill Swash Plate
touch Leveler as shown.
page 32
90°
Chapter 19: Adjustment Servos with Leveler
Front Servo
90
90
Left Servo
page 33
Right Servo
Chapter 20: Canopy Installation
page 34
Chapter20: Exploded View, Main Rotor
11
24
27
13
1
7
21
22
2
3
14
4
19
12
15
26
5
25
9
10
8
20
6
18
16
23
POS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Page 34
Code
OXY0227
OR3W1.5
OXY0446
OXY0229
OXY0524
OXY0528
TCEM1.6X6
TCEM2X8
OXY0525
TCEM1.6X5 M1.6X5 Hex Cap Screw
OXY0529
OXY0530
OXY0447
OXY0519
OXY0526
OXY0234
MR6700 ZZC
OXY0233
OXY0017
OXY0016
OXY0020
OXY0454
OXY0521
OXY0228
SMR682Z-ZZ
F2.5-6GC
OXY0078
Linkage ball 3x1.5mm - DR1265
Name
OXY2-CENTER HUB
Oring ID3x1.5
OXY2 Sindle Shaft
OXY2-Dampener Bushing
2.55x4.5x0.1 Shim
OXY2-Damperner Spacer
M1.6x6 Hex Cap Screw
M2X8HEX CAP SCREW
1.6x3.5x0.5 Washer
OXY2-DFC Arm
OXY2-2x4X4.4 Bushing
OXY2-DFC Pin Screw
Threaded Rod M1.4X7mm
Plastic Linkage Ball 3mm
OXY2-Lower Swash Plate
10X15W4 RADIAL BEARING
OXY2-Upper Swash Plate
CENTER BALL
BALL HOLDER
M1.2x2 SPECIAL SCREW
OXY2-Anti Rotation PIN
OXY2- Main Grip
2.5X6X2.6 Radial Bearing
2.5x6x3 Thrust Bearing
M2X10 BUTTOM SCREW
QTY.
1
2
1
2
4
2
2
1
2
2
2
2
2
2
2
1
1
1
1
1
2
1
5
2
4
2
2
Chapter20: Exploded View, Main Frame
17
4
2
19
1
9
16
6
7
10
3
28
8
14
20
18
13
12
POS
1
2
3
4
7
8
9
10
11
12
13
14
15
16
17
18
19
28
page 35
Code
OXY0235
MR104_ZZC
OXY0236
OXY0251
OXY0521
TCEM2X6
OXY0525
TCEM1.6X5 M1.6X5 Hex Cap Screw
OXY0263
OXY0533
OXY0538
FHSM2X4
OXY0247
OXY0459
OXY0451
OXY0081
TCEM1.6X6
OXY0547
Upper Main Shaft Bearing Block
Lower Main Shaft Bearing Block
Linkage ball 3x1.5mm - DR1265
Pinion 12T - 2mm Motor Shaft
Name
4X10X4 RADIAL BEARING
OXY2-Anti Rotaion Guide
M2X6HEX CAP SCREW
1.6x3.5x0.5 Washer
OXY2-Main Frame
OXY2-Main Gear 55t Pulley
CF Main Gear Cover
M2x4 Flat Head Screw
OXY2-Main Gear Bushing
OXY2-Main Shaft
OXY2-Main Shaft Collar
2.1X5.5X1 WASHER
M1.6x6 Hex Cap Screw
QTY.
1
2
1
1
3
9
6
16
1
1
1
3
1
1
1
4
1
1
Chapter20: Exploded View, Main Frame
7
6
5
8
9
4
2
1
17
15
16
13
3
Pos.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
page 36
Code
OXY0461
OXY0263
OXY0300
OXY0452
OXY0242
MR52-W2
OXY0460
OXY0532
OXY0453
OXY0237
OXY0240
OXY241
TBES2X8
TBES2X6
TCEM2X6
OXY0260
TCEM1.6X5
Name
Break Away Canopy
OXY2-Main Frame
OXY2- Battery Tray
OXY2-Boom Clamp
OXY2-Pulley Guide Belt
2X5X2 Radial Bearing
OXY2 Bell Crank Bushing
1.6x13.8mm Pin
Boom Lock Rod
OXY2-Bottom Landing Gear
OXY2-Right Landing Gear
OXY2-Left Landing Gear
M2X8 Self Tapping Screw
M2X6 Self Tapping Screw
M2X6HEX CAP SCREW
Canopy Mount
M1.6X5 Hex Cap Screw
11
QTY.
2
2
1
2
2
4
4
2
4
1
1
1
4
6
8
2
2
10
12
14
Chapter20: Exploded View, Tail System
10
26
32
17
1
16
11
30
20
21
28
5
4
9
27
14
19
23
24
18
2
22
25
3
29
31
6
3
34
45
38
45
44
39
POS
page 37
1
2
3
4
5
6
7
8
9
10
11
12
13
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Code
OXY0578
OXY0543
SMR682Z-ZZ
OXY0524
OXY0258
OXY0516
OXY0279
OXY0252
MR52-W2
OXY0448
OXY0521
OXY0460
OXY0457
OXY0255
OXY0522
OXY0523
PanM1.4x4
OXY0253
OXY0537
SMR682-ZZ
PanM1.4x3
OXY0527
OXY0551
TCEM1.6X10
OXY0540
OXY0515
TCEM1.6X5
Name
OXY2 Tail Boom STD ( Black )
OXY2-Al Tail Case
2.5X6X2.6 Radial Bearing
2.55x4.5x0.1 Shim
OXY2-Tail Case Center
2x3.5x2.2 Bushing
OXY2-Vertical Fin Bushing
OXY2-AL Tail Bell Crank
2X5X2 Radial Bearing
OXY2-Bell Crank Pin Screw
Linkage ball 3x1.5mm - DR1265
OXY2 Bell Crank Bushing
OXY2-Tail Pitch Slider Bushing
OXY2-Tail Pitch Slider
OXY2-Link Control
OXY2-Link Control Buhing
M1.4x4 Pan Head Screw
OXY2-Tail Hub
OXY2-AL Tail Grip
2X5X2.3 Radial Bearing
M1.4x3 Pan Head Screw
2x3.5x0.1 Shim
1.5x2.8H0.4 Washer
M1.6X10 Hex Cap Screw
OXY2-Tail Case Rod
OXY2-Tensioner Bushing
M1.6X5 Hex Cap Screw
QTY.
1
1
4
2
1
1
1
1
4
2
3
2
1
1
2
2
2
1
2
4
2
3
2
1
1
1
6
POS
29
30
31
32
33
34
35
36
39
40
41
42
43
44
45
Code
TCEM1.6X5
TCEM1.6x8
TCEM2X12
SCM3x3
OXY0256
OXY0067
OXY0539
OXY0257
OXY0535
OXY0584
OXY0536
OXY0526
OXY0519
OXY0525
TCEM1.6X5
Name
M1.6X5 Hex Cap Screw
M1.6x8 Hex Cap Screw
M2X12 Hex Cap Screw
Set Screw M3x3
Tail Shaft 15T
Guide Push Rod
M2.5 Pin Screw
OXY2-Vertical Fin
Tail Servo Mount
std tail push Carbon Rod
OXY2-Al Tail Push Rod Terminal
Plastic Linkage Ball 3mm
Threaded Rod M1.4X7mm
1.6x3.5x0.5 Washer
M1.6X5 Hex Cap Screw
QTY.
6
2
1
1
1
1
2
1
2
1
2
2
2
2
4
40
41
42
43
Chapter 21: Spare Parts
SP-OXY2-001-OXY2CNC Aluminum Center Hub
1 x OXY2-Center Hub
2 x M1.6x6 Hex Cap Screw
1 x M2X8 Hec Cap Screw
SP-OXY2-004 - OXY2 Plastic DFC Arm, Set
2 x OXY2-DFC Arm
2 x Threaded Rod M1.4X7mm
2 x Plastic Linkage Ball 3mm
SP-OXY2-002 - OXY2 CNC Aluminum Main Grip, Set
2 x OXY2- Main Grip
4 x 2.5X6X2.6 Radial Bearing
2 x 2.5x6x3 Thrust Bearing
2 x 2.55x4.5x0.1 Shim
2 x M2X10 Buttom Screw
SP-OXY2-005 3 mm Linkage Ball, 10Pcs
10 x Plastic Linkage Ball 3mm
SP-OXY2-003 - OXY2 Damperner, Set
2 x OXY2-Damperner Spacer
2 x 2.55x4.5x0.1 Shim
2 x OXY2-Dampener Bushing
2 x O'ring ID3x1.5
SP-OXY2-006 M1.4x11 Threaded Rod, 10Pcs
10 x M1.4X11 Threaded Rod
SP-OXY2-007 OXY2 - Main Shaft, 2 PCS
2 x OXY2-Main Shaft
1 x OXY2-Main Shaft Collar
1 x M1.6x6 Hex Cap Screw
4 x M2X8 Hex Cap Screw
page 38
SP-OXY2-008 - OXY2 Spindle Shaft, 2 Set
2 x OXY2 Sindle Shaft
4 x 1.6x3.5x0.5 Washer
4 x M1.6X5 Hex Cap Screw
SP-OXY2-009 3mm Steel Ball, 10 PCS
10 x Linkage ball 3x1.5mm
SP-OXY2-010 - OXY2 Swash Plate, Service Bag
SP-OXY2-011 - OXY2 Swash Plate, Set
Chapter 21: Spare Parts
SP-OXY2-013 - OXY2 Main Grip Service Bag
1 x Ball Holder
1 x Center Ball
2 x M1.2x2 Special Screw
SP-OXY2-058 - OXY2 DFC Pin Screw, Set
2 x OXY2-DFC Pin Screw
2 x OXY2-2x4X4.4 Bushing
1 x OXY2-Lower Swash Plate
1 x OXY2-Upper Swash Plate
1 x 10X15W4 Radial Bearing
1 x Center Ball
1 x Ball Holder
2 x M1.2x2 Special Screw
1 x OXY2-Anti Rotation Pin
1 x Linkage ball 3x1.5mm
4 x 2.5X6X2.6 Radial Bearing
2 x 2.5x6x3 Thrust Bearing
2 x 2.55x4.5x0.1 Shim
2 x M2X10 Button Screw
page 39
Chapter 21: Spare Parts
SP-OXY2-014 - OXY2 Anti Rotation Guide
1 x OXY2-Anti Rotaion Guide
SP-OXY2-017 - OXY2 Motor Mount, Set
SP-OXY2-015 - OXY2 Upper Main Shaft Bearing Block
1 x Upper Main Shaft Bearing Block
9 x M1.6X5 Hex Cap Screw
3 x 1.6x3.5x0.5 Washer
1 x 4X10X4 Radial Bearing
SP-OXY2-018 - OXY2 CNC Main Gear
SP-OXY2-016 - OXY2 Lower Main Shaft Bearing Block
1 x Lower Main Shaft Bearing Block
7 x M1.6X5 Hex Cap Screw
3 x 1.6x3.5x0.5 Washer
1 x 4X10X4 Radial Bearing
SP-OXY2-019 -OXY2 Main Frame, 2PCS
1 x OXY2 - Motor Mount
6 x M2X6 Hex Cap Screw
4 x 2.1X5.5X1 Washer
2 x M2.5x5 Button Screw
page 40
1 x CNC Main Gear 55t Pulley
1 x CF Main Gear Cover
3 x M2x4 Flat Head Screw
1 x M2X8 Hex Cap Screw
2 x OXY2-Main Frame
SP-OXY2-020 - OXY2 Break Away Canopy , 2PCS
SP-OXY2-021 - OXY2 CNC Aluminum Canopy Mount
Chapter 21: Spare Parts
SP-OXY2-022 - OXY2 Bottom Plate
2 x OXY2-Break Away Canopy
SP-OXY2-023 - OXY2 Plastic Landing Gear Skid, Left / Right
1 x OXY2-Right Landing Gear, black
1 x OXY2-Left Landing Gear, black
SP-OXY2-026 - OXY2 CNC Aluminum Belt Pulley Guide, Set
2 x Canopy Mount
2 x M1.6X4 Hex Cap Screw
SP-OXY2-024 - OXY2 Battery Tray 3D
1 x OXY2- Battery Tray
6 x M2X6 Self Tapping Screw
SP-OXY2-027 - OXY2 Boom Mount Lock Rod, Set
1 x OXY2-Bottom Landing Gear
4 x M2X8 Self Tapping Screw
SP-OXY2-025 - OXY2 Boom Clamp Mount 3D
2 x OXY2-Boom Clamp
4 x Boom Lock Rod
8 x M2X6 Hex Cap Screw
SP-OXY2-057 - OXY2 Main Gear Spacer
2 x OXY2-Pulley Guide Belt
4 x 2X5X2 Radial Bearing
4 x OXY2 Bell Crank Bushing
2 x 1.6x13.8mm Pin
page 41
4 x Boom Lock Rod
8 x M2X6 Hex Cap Screw
1 x OXY2-Main Gear Bushing
Chapter 21: Spare Parts
SP-OXY2-029 - OXY2 Tail Shaft 15T
1 x OXY2-Tail Shaft
1 x 15T Tail Pulley
2 x OXY2-Tail Flange Pulley
4 x 2.55x4.5x0.1 Shim
SP-OXY2-032 - OXY2 CNC Aluminum Tail Grip, Set
SP-OXY2-030 - OXY2 Tail Shaft 16T
1 x OXY2-Tail Shaft
1 x 16T Tail Pulley
2 x OXY2-Tail Flange Pulley
4 x 2.55x4.5x0.1 Shim
SP-OXY2-033 - OXY2 Tail Rotor - Service Bag
SP-OXY2-031 - OXY2 Tail Rotor Hub, Spare
1 x OXY2-Tail Hub
2 x M1.4x3 Pan Head Screw
2 x 1.5x2.8H0.4 Washer
1 x Set Screw M3x3
SP-OXY2-034 - OXY2 CNC Aluminum Tail Bell Crank
2 x OXY2-AL Tail Grip
4 x 2X5X2.3 Radial Bearing
2 x 2x3.5x0.1 Shim
2 x Linkage ball 3x1.5mm
2 x M1.6x8 Hex Cap Screw
page 42
4 x 2X5X2.3 Radial Bearing
2 x 2x3.5x0.1 Shim
2 x Linkage ball 3x1.5mm
2 x M1.6x8 Hex Cap Screw
1 x OXY2-AL Tail Bell Crank
2 x 2X5X2 Radial Bearing
2 x OXY2-Bell Crank Pin Screw
1 x Linkage ball 3x1.5mm
2 x OXY2 Bell Crank Bushing
1 x M1.6X10 Hex Cap Screw
SP-OXY2-035 - OXY2 CNC Aluminum Tail Case
SP-OXY2-036 - OXY2 CNC SST Tail Belt Tensioner
Chapter 21: Spare Parts
SP-OXY2-038 OXY2 - Vertical Fin
1 x Al Tail Case
2 x 2.5X6X2.6 Radial Bearing
1 x 2.55x4.5x0.1 Shim
1 x M1.6X10 Hex Cap Screw
4 x M1.6X5 Hex Cap Screw
1 x Tail Case Rod
SP-OXY2-039 - OXY2 CNC Tail Pitch Slider
1 x OXY2-Tail Pitch Slider Bushing
1 x OXY2-SST Tail Pitch Slider Ring
2 x 3x7x2 Radial Bearing
1 x OXY2-Tail Pitch Slider Haft Moon
2 x OXY2-Link Control
2 x OXY2-Link Control Buhing
2 x M1.4x4 Pan Head Screw
SP-OXY2-042 - OXY2 CNC Aluminum Tail Servo Mount- Set
1 x OXY2-Tensioner Bushing
2 x 2X5X2 Radial Bearing
1 x 2x3.5x0.1 Shim
1 x M2X12 Hex Cap Screw
SP-OXY2-040 - OXY2 Tail Pitch Slider - Service Bag
2 x OXY2-Link Control
2 x OXY2-Link Control Buhing
2 x M1.4x4 Pan Head Screw
SP-OXY2-043 - OXY2 Tail Case Hub, Set
1 x OXY2-Vertical Fin
1 x 2x3.5x2.2 Bushing
1 x OXY2-Vertical Fin Bushing
2 x 2.5X6X2.6 Radial Bearing
1 x 2.55x4.5x0.1 Shim
3 x M1.6X5 Hex Cap Screw
SP-OXY2-041 - OXY2 CNC Tail Push Rod, Set
1 x std tail push Carbon Rod
2 x OXY2-Al Tail Push Rod Terminal
2 x Plastic Linkage Ball 3mm
2 x Threaded Rod M1.4X7mm
1 x Guide Push Rod
2 x M2.5 Pin Screw
SP-OXY2-044 - OXY2 Tail Boom, 2PC
2 x CNC Tail Servo Mount
2 x 1.6x3.5x0.5 Washer
4 x M1.6X5 Hex Cap Screw
SP-OXY2-065 - OXY2 Tail Bell Crank - Service Bag
2 x OXY2-Bell Crank Pin Screw
1 x Linkage ball 3x1.5mm
1 x M1.6X10 Hex Cap Screw
page 43
1 x OXY2-Tail Case Center
4 x M1.6X5 Hex Cap Screw
SP-OXY2-056 - OXY2 STD Timing Belt
1 x 305T Timing Belt
1 x Front Boom Insert
2 x OXY2 std tail Boom
SP-OXY2-012 - OXY2 Blade Holder
SP-OXY2-028-OXY2 Battery Oring , 4PC
Chapter 21: Spare Parts
SP-OXY2-045 - OXY2 190mm Carbon Plastic Main Blade
1 x OXY2 Blader Holder
SP-OXY2-046 - OXY2 38mm Tail Blade, Black
2pcs 38mm Tail Blade, Black 2pcs 41mm Tail Blade, Black
SP-OXY2-049 - OXY2 Pinion 11T - 2mm Motor Shaft
4 x Oring 55W2.5
SP-OXY2-047 - OXY2 41mm Tail Blade, Black
SP-OXY2-050 - OXY2 Pinion 12T - 2mm Motor Shaft
2pcs 190mm Carbon Plastic Main Blade
SP-OXY2-048 - OXY2 Pinion 10T - 2mm Motor Shaft
1 x Pinion 10T- M0.4 - 2mm Motor Shaft
SP-OXY2-051 - OXY2 Pinion 13T - 2mm Motor Shaft
1 x Pinion 11T- M0.4 - 2mm Motor Shaft 1 x Pinion 12T- M0.4 - 2mm Motor Shaft
SP-OXY2-052 - OXY2 Pinion 14T - 2mm Motor Shaft
1 x Pinion 14T- M0.4 - 2mm Motor Shaft
page 44
SP-OXY2-053 - OXY2 Pinion 14T - 2.5mm Motor Shaft
1 x Pinion 14T- M0.4 - 2.5mm Motor Shaft
1 x Pinion 13T- M0.4 - 2mm Motor Shaft
SP-OXY2-054 - OXY2 Pinion 16T - 2.5mm Motor Shaft
1 x Pinion 16T- M0.4 - 2.5mm Motor Shaft
SP-OXY2-055 - OXY2 Pinion 18T - 2.5mm Motor Shaft
SP-OXY2-059 - OXY2 Vertical Fin Sticker Yellow
Chapter 21: Spare Parts
SP-OXY2-060 - OXY2 Vertical Fin Sticker Orange
1 x Pinion 18T- M0.4 - 2.5mm Motor Shaft
SP-OXY2-061 - OXY2 Vertical Fin Sticker White
1 x Vertical Fin Sticker White
SP-OXY2-064 - OXY2 3D Leveler Tool
1 x Vertical Fin Sticker yellow
SP-OXY2-062 - OXY2 Vertical Fin Sticker Green
1 x Vertical Fin Sticker Green
1 x Vertical Fin Sticker Orange
SP-OXY2-063 - OXY2 Fiber Glass Canopy Schema # 1
1 x Orange Canopy
1 x Leveler Tool
page 45
Loading...