OWNER’S MANUAL
Wireless Surround Speaker System
®
Wireless Surround
®
DRAFT
English
IMPORTANT SAFETY INSTRUCTIONS
EAD BEFORE OPERATING EQUIPMENT
R
1. Read these instructions.
. Keep these instructions.
2
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
. Do not block any ventilation openings. Install in accordance
7
with the manufacturer’sinstructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your
safety.If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer,or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms
or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
15. WARNING: Toreducethe risk of fire or electric shock, this
apparatus should not be exposed to rain or moisture and objects
filled with liquids, such as vases, should not be placed on this
apparatus.
16. Tocompletelydisconnectthis equipment from the mains,
disconnect the power supply cord plug from the receptacle.
17. The main plug of the power supply cord shall remain readily
operable.
WARNING: Listen Carefully
olk Audio loudspeakers and subwoofers are capable of playing at ex-
P
tremely high volume levels, which could cause serious or permanent
earing damage. Polk Audio, Inc. accepts no liability for hearing loss,
h
bodily injury or property damage resulting from the misuse of its products. Keep these guidelines in mind and always use your own good
judgment when controlling volume: You should limit prolonged expo-
ure to volumes that exceed 85 decibels(dB).
s
or more about safe volume levels refer to the Occupational
F
Health and Safety Administration (OSHA) guidelines at
ww.osha.gov/dts/osta/otm/noise/standards_more.html.
w
PRODUCT DISPOSAL
ertain international, national and/or local
C
aws and/or regulations may apply regarding
l
the disposal of this product. For further detailed information, please contact the retailer
where you purchased this product or the Polk
udio Importer/ Distributor in your country.
A
can be found on the Polk Audio website www.polkaudio.com
or by contacting Polk Audio at: 5601 Metro Drive, Baltimore,
aryland 21215, USA Phone: +1 410 358-3600.
M
A listing of Polk Audio Importer/ Distributors
TECHNICAL ASSISTANCE OR SERVICE
If, after following the hookup directions, you experience
difficulty, please double-check all wire connections.
Should you isolate the problem to the speaker, contact
the authorized Polk Audio dealer where you made your
purchase, or contact Polk Audio Customer Service
800-377-7655 (M-F, 9am-6pm
or via email polkcs@polkaudio.com. Outside the US
& Canada, call 410-358-3600. More detailed information
including audio how-to articles, FAQs and online manuals
are available on our award-winning website:
www.polkaudio.com.
, US & Canada only)
EST
IC WARNING
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause
undesired operation of the device.”
To reduce potential radio interference to
other users, the antenna type and its
gain should be so chosen that the
equivalent isotropic ally radiated
power (e.i.r.p.) is not more than
that permitted for successful communication.
FCC Radiation Exposure Statement
This equipment complies with FCC
radiation exposure limits set forth for
an uncontrolled environment.
This equipment should be installed and
operated with minimum distance 20cm between
the radiator & your body
he CAUTION marks shown here are located
T
n the back of your F/X Wireless Surround.
o
CAUTION: To prevent electric shock, match
wide blade of plug to wide slot, insert fully.
CAUTION: No naked flame sources, such as
andles, should be placed on the apparatus.
c
Class B Emissions Limits
This Class B digital apparatus meets all requirements of
he Canadian Interference–Causing Equipment Regulations.
t
NOTE:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and, if not installed and used
in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
FCC WARNING STATEMENT
FCC NOTE:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY
RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
Customer Service Hours of Operation: Monday-Friday, 9AM-6
PM EST
polkcs@polkaudio.com 54 Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
1
2
R
ear
4
3
Top
1
2
3
4
5
6
3
4
1
2
FIRST THINGS FIRST
6
2
3
4
5
1
Caution: Exercise caution when
unpacking your Polk Audio
F/X Wireless Surround.
Please check to ensure you
have everything in your carton.
Inside, you should find:
• F/X Wireless Surround Loudspeaker
• 2.4GHz Transmitter
• Two 5' RCA Wires
• Power Supply for Transmitter
• Power Supply for Loudspeaker
• Owner’sManual
• Transmitter Wall Mount Template
• Online Registration Card
If anything is missingor damaged, or if your
Polk Audio F/X Wireless Surroundfails to
operate,please notify your dealer immediately.
We recommend keeping your original carton
and packing materials in case you need to ship the
unit in the future.
WHERE TO LOCATE YOUR
F/X WIRELESS SURROUND
FOR THE BEST SOUND
Place your F/X Wireless Surroundin one of three different locations in your room (on the floor, on a table
or on an elevated open shelf) and up to 30' (10 me-
ters) from the loudspeaker’s transmitter:
We do recommend placing your F/X
Wireless Surround in different locations
within your room to learn which location
produces the best sound quality based upon
your listening preferences.
Important Note: Whichever location you choose,
ensure the room location switch on the amplifier
plate located on the bottom of loudspeaker is set to
the appropriate position: “floor,” “table”or “shelf.”
The only wire that plugs into the F/X Wireless Surround is the power cord, which you plug into an AC
outlet.
Specifications
1/8" H x 19 1/2" W x 7 3/4
Dimensions
8
206.38mm H x 495.3mm W x 195.85mm D
System Power 100 Watts
Loudspeaker Weight 18 lbs (8.16kg)
Speaker Compliment 4 - 2 1/2" CDA Drivers
1 - 5 1/4" Woofer
Transmitter Hookups
Once you have decided on a location for your
loudspeaker, hook up the transmitter to either
your receiver or pre-amp.
Transmitter Inputs
Audio Inputs—Speaker Level and Line Level.
This is where you connect your transmitter to
your receiver or pre-amp. You may make either
speaker level or line level connections, but
never make both connections at the same time.
The speaker level inputs are the default
input mode
Power Connection—The transmitter power
supply is connected here.
F/X Wireless Surround Controls
Power LED—Shines blue when the
speaker is on, red when in stand-by.
Room Position Button—This button sets
the equalization for the F/X Wireless Surround
based on its location,either on the floor, on a
table or on a shelf. An LED indicates which
locationis chosen.
Scan—Push this button should it become
necessary to re-establish the “communication” link between the transmitter and
the loudspeaker.
Wireless LED—Shines blue to indicate
the transmitter and loudspeakerare connected wirelessly. Flashes blue/red when
loudspeaker and transmitterare connecting
and shines red when loudspeaker and
transmitter are not connected.
Follow the Quickstart Guide at the front of this
manual for hookup instructions.Or you may refer
to the hookup schematics on page 9.
Power LED—Shines blue to indicate
the transmitter is active and connected
successfully to the receiver. Shines red to
indicatethe transmitter and loudspeaker
have failed to establish a wirelessconnection.
Scan—Push this button should it become
necessary to re-establish the communication
link between the transmitter and loudspeaker.
Power Connection—The loudspeaker
power supply is connected here.
AC Mains––The AC Mains Switch turns
the loudspeaker on and off, though you
may leave the switch turned on all the time.
Customer Service Hours of Operation: Monday-Friday, 9AM-6PM EST polkcs@polkaudio.com 76 Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
CONNECTING YOUR F/X WIRELESS
sub
speaker level line level
LL
RR
surr.back
surround
LL
RR
Receiver/Processor
Transmitter
++
+
--
-
+
-
+
-
+
-
L
L
R
R
s
urr. back surround
speaker level line level
f
ront
L
L
R
R
L
R
L
R
s
urr.back
s
urround
surr.back
s
urround
Receiver/Processor
Transmitter
SURROUND TRANSMITTER
IMPORTANT NOTE: WHILE THE F/X WIRELESS
SURROUNDCAN BE CONNECTED USING EITHER LINE
LEVEL OR SPEAKER LEVEL HOOKUPS, WE RECOMMEND USING THE SPEAKERLEVEL INPUTS.
NOTE: USE ONLYONE OF THESE OPTIONS. NEVER
COMBINEHOOKUP OPTIONS.
OPTION #1
Speaker Level Connections
• Connect the transmitter’s left and
right Surround and Surround Back
inputs directly to the corresponding
left and right Surround and Surround
Back outputs on your receiver/processor
5.1 AND 7.1 CHANNEL
CONNECTION OPTIONS
Depending on your home theater receiver/processor,
you will either be using a 5.1 or 7.1 channel hookup. If
you have a 5.1 receiver, connect the left and right Surround channels to your F/X WirelessSurround.If you
are using a 7.1 channel receiver connect both the
left and right Surround Back, and the left and right
Surroundchannels.
SETTING UP YOUR F/X
WIRELESS SURROUND
F/X Wireless Surround Position setting:
Your F/X Wireless Surround can provide a credible multi-channel surround experience from a
range of placement locations within the media
space but should optimally be placed behind the
seating area. Choose FLOOR, TABLE (ear height
of +/- 2 feet) or SHELF (2 feet or more above ear
height) in accordance with the vertical placement of the loudspeakercabinet.
Due to the special nature of its complex radiation
pattern,the top surface of the loudspeaker cabinet should be unobstructed and facing towards
the ceiling. The long axis of the cabinet should
be parallel to the long dimension of your home
theater’s video screen and centered behind the
listening area
IMPORTANT NOTE:
anual vs. Automated LoudspeakerSetup
M
any new home theater receivers and preamp/processorsfea-
M
ure automated setup systems such as Audyssey
t
to the special nature of the F/X Wireless Surround’s operating
principles, we strongly recommend not using an automated
speaker calibration system for Surround and Surround Back
hannel loudspeakers.
c
®
M
ultEQ. Due
Follow The Instructions Below To Set Up
Your F/X Wireless Surround Manually.
Gain:
For optimal performance, channel level settings
on Dolby Digital receivers/surround-sound
processors for the (lateral) Surround and Surround Back channels should match each other.
1. SurroundChannel gain should be set so that
the sound level in the seating area matches
or slightly exceedsthe sound levels of the
front channels.
• Adjust your receiver’s speaker
configurations as follows:
Surrounds and
SurroundBack = SMALL
OPTION #2
Line Level Connections
• Using the supplied RCA cables, connect
the left and right Surround and Surround
Back outputs on your receiver to the
corresponding left and right Surround and
SurroundBack inputs on the transmitter.
• Adjust your receiver’s speaker
configurations as follows:
Surrounds and
Surroundback = SMALL
TELEVISION
F/X WIRELESS SURROUND
2. SurroundBack should be set to match
the gain setting so determined for the
SurroundChannels.
Example:If +3dB is the appropriate
channel level to achieve SurroundChannel
sound levels that match the Front channels,
then Surround Back channel level should also
be set to +3dB.
Customer Service Hours of Operation: Monday-Friday, 9AM-6PM EST polkcs@polkaudio.com 98 Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
SET UP (continued)
AB
Distance To Listener:
“Distance” settings govern channel delay for
optimal performance from Dolby Digital 5.1 and
7.1 sources. For the F/X WirelessSurround,you
need to determine the actual distance from the
listening area to the loudspeaker cabinet and
approximate room dimensions.
For symmetrical rooms, wherebythe distance
between the loudspeaker cabinet and major
reflecting surfaces (particularly side walls) are
approximately equal, the distance setting for the
Surroundchannels may be computedas follows:
• Distance = actual distance of speaker behind
the listening area and approximate width of
the listening area
• The distance setting for Surround Back
channelsshould simply match the actual
distance of the loudspeaker from the
listening area.
Figure A
CENTER
C
HANNEL
LEFT
CHANNEL
F/X WIRELESS SURROUND
Figure B
LEFT
CHANNEL
RIGHT
CHANNEL
CENTER
CHANNEL
SUB
RIGHT
CHANNEL
SUB
TROUBLESHOOTING
Loudspeaker does – Ensure the loudspeaker is plugged
not power on. into a live wall outlet.
– Ensure the rear panel power switch
is in the “On” position.
No sound from loudspeaker. – Push the SCAN button to reset the
“communications” link between
the transmitter and the loudspeaker.
– Turn up the volume control of the individual
channelsthrough your receiver.
– Make sure the transmitter is plugged into a
live wall outlet
The loudspeaker’s sound – Turn off and unplug the transmitterand
is intermittent, sounds the loudspeaker. Then turn on the loudspeaker
weak or is distorted. and plug in the transmitter.
– Push the SCAN button on the transmitter and
loudspeaker sequentially to reset the
“communications” link between
the transmitter and the loudspeaker.
– The loudspeaker could be too far
away from the transmitter to receive a
sufficiently strong signal. Trymoving it closer.
Example:
F/X WIRELESS SURROUND
The F/X Wireless Surround is placed 4 feet behind the seating area in a 20-foot wide room. Set
the Surround Right and Surround Left distanceto
40ms (milliseconds)
Symmetrical Room: Surround Right and
Surround Left Speaker distance
Speaker Time Delay In Milliseconds
2
10 30 30 31 32 33 34 38
Room
Width
12 32 32 33 33 34 36 39
15 35 35 36 36 37 38 41
(ft)
20 40 40
25 45 45 45 46 46 47 49
ForNon-Symmetrical Arrangements
(Figure A)
Distance of speaker behind listening area (ft)
3 4 6 8 10 15
40
41 42 42 45
(Figure B)
To determine distance settingsin an
assymetrical room, subtractthe distance
of the loudspeaker from the closest wall (B)
from the farthest (A), and then divide that
number by two. EX: (A-B)
2
10 Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
TECHNICAL ASSISTANCE
AND SERVICE
If, after following these hookup directions, you
experience difficulty, please double-check all
wire connections. Should you isolate the problem to the loudspeaker, contact the authorized
Polk Audio dealer where you made your purchase, or call Polk Audio’s friendly Customer
Service Departmentat: 1-800-377-7655 (calls
from US or CAN only), 410-358-3600 9am
to 6pm EST,Monday through Friday.
You may also contact us via email:
polkcs@polkaudio.com. For more detailed
hookup informationand manual updates,
visit: www.polkaudio.com.
Specifications can be found on the
F/X Wireless Surround web pages.
Go to www.polkaudio.com.
Customer Service Hours of Operation: Monday-Friday, 9AM-6PM EST polkcs@polkaudio.com 11
A Note Regarding Wireless Performance:
Like all wireless devices, your F/X Wireless Surround
may be susceptible to RF interference from such
sources as microwave ovens, WiFi computer
systems, video game systems, cordless telephones,
blue tooth systems, baby monitors and other
devices. In particular, any devices operating in the
2.4GHz band may cause intermittent wireless
connections between the F/X Wireless Surround.
It is also possible that your F/X Wireless Surround
may affect other wireless systems. For the most
part, you can avoid wireless performance problems
by physically separating these devices from your F/X
Wireless Surround . Maintaining a distance of several
feet or more between your F/X Wireless Surround
speaker and any wireless device should prevent any
mutual interference effects. If you do notice any
subwoofer signal dropouts take care to identify the
root cause (most commonly having other wireless
devices too close) and resolve accordingly. Any
interference effects from a microwave oven will
cease once the oven stops operating and may be
resolved on a long-term basis by increasing the
physical distance between your F/X Wireless
Surround and the microwave oven.
IMITED WARRANTY
L
olk Audio, Inc., warrants to the original retail purchaser only. This warranty will terminate automatically prior to its stated expiration
P
if the
riginal retail purchaser sells or transfers the Product to any other party.
o
olk Audio, Inc., warrants, to the original retail purchaser only, that the LOUDSPEAKER(S), PASSIVE CROSSOVER COMPONENT(S) and
P
ENCLOSURE on this Polk Audio Loudspeaker Product will be free from defects in material and workmanship for a period of five (5)
ears from the date of original retail purchase from a Polk Audio Authorized Dealer.
y
Furthermore, Polk Audio, Inc., warrants, to the original retail purchaser only, that any AMPLIFIER OR OTHER ELECTRONIC COMPO-
ENT that may be included in this Polk Audio Loudspeaker Product will be free from defects in material and workmanship for a period
N
of three (3) years from the date of original retail purchase from a Polk Audio Authorized Dealer.
o allow Polk Audio to offer the best possible warranty service, please register your new product online at: www.polkaudio.com/regis-
T
tration or call Polk customer service 800-377-7655 in the USA and Canada (outside the USA: 410-358-3600) within ten (10) days of the
ate of original purchase. Be sure to keep your original purchase receipt.
d
Defective Products must be shipped, together with proof of purchase, prepaid insured to the Polk Audio Authorized Dealer from whom
you purchased the Product, or to the Factory at 1 Viper Way Vista, CA 92081. Products must be shipped in the original shipping container or its equivalent; in any case the risk of loss or damage in transit is to be borne by you. If upon examination at the Factory or
Polk Audio Authorized Dealer it is determined that the unit was defective in materials or workmanship at any time during this Warranty period, Polk Audio or the Polk Audio Authorized Dealer will, at its option, repair or replace this Product at no additional charge,
except as set forth below. All replaced parts and Products become the property of Polk Audio. Products replaced or repaired under this
warranty will be returned to you, within a reasonable time, freight prepaid.
This warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate
packing or shipping procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, cosmetic appearance of
cabinetry not directly attributable to defect in materials or workmanship, or service, repair,or modification of the Product which has
not been authorized or approved by Polk Audio. This warranty shall terminate if the Serial number on the Product has been removed,
tampered with or defaced.
This warranty is in lieu of all other expressed Warranties. All implied warranties on this Product are limited to the duration of this expressed Warranty. Some states do not allow limitation on how long an implied Warranty lasts, so the above limitations may not apply
to you. This Warranty gives you specific legal rights, and you also may have other rights which vary from state to state.
If this Product is defective in materials or workmanship as warranted above, your sole remedy shall be repair or replacement as provided above. Thiswarranty does not cover service, parts, or supplies to repair damage to property other than the Product. In no event
will Polk Audio, Inc. be liable to you for any incidental or consequential damages arising out of the use or in-ability to use the Product,
even if Polk Audio, Inc. or a Polk Audio Authorized Dealer has been advised of the possibility of such damages, or for any claim by any
other party. Some states
do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply
to you.
This Warranty applies only to Products purchased in Canada, the United States of America, its possessions, and U.S. and NATO armed
forces exchanges and audio clubs. The Warranty terms and conditions applicable to Products purchased in other countries are available from the Polk Audio Authorized Distributors in such countries.
ARANTIE LIM ITÉE
G
a garantie de Polk Audio, Inc., n’est valide que pour l’acheteur au détail original. La garantie sera automatiquement annulée avant sa
L
date d’expiration spécifiée si l’acheteur original vend ou transfère le produit à tout autre parti.
Polk Audio, Inc., garantit - à l’acheteur au détail original seulement - que le ou les HAUT-PARLEUR(S), COMPOSANTE(S) DE FILTRE PAS-
IF et CAISSON(S) de ce produit Polk Audio seront exempts de tout défaut attribuable aux pièces d’origine et à la main d’oeuvre pour
S
une période de cinq (5) ans à partir de la date de l’achat au détail original chez un revendeur agréé Polk Audio.
n outre, Polk Audio, Inc., garantit - à l’acheteur au détail original seulement - que TOUT AMPLIFICATEUR OU TOUT AUTRE COM-
E
POSANTE ÉLECTRONIQUE qui pourrait faire partie ce produit Polk Audio sera exempt de tout défaut attribuable aux pièces d’origine et
la main d’oeuvre pour une période de trois (3) ans à partir de la date de l’achat au détail original chez un revendeur agréé Polk Audio.
à
Pour permettre à Polk Audio de vous offrir le meilleur service de garantie possible, veuillez enregistrer votre nouveau produit en ligne à
’adresse web www.polkaudio.com/registration - ou contactez le Service à la Clientèle de Polk au 800-377-7655 aux États-Unis et au
l
Canada (à l’extérieur des É.U.:410-358-3600) dans les dix (10) jours suivant la date de l’achat original. Assurez-vous de conserver votre
eçu d’achat original.
r
Les produits défectueux doivent être expédiés, avec une preuve d’achat, francs de port et assurés, au revendeur agree Polk Audio de
qui vous avez acheté le produit, ou à l’usine Polk Audio,1 Viper Way Vista, CA 92081.
Les produits doivent être expédiés dans leur carton d’expédition original ou dans un contenant équivalent. Le propriétaire doit assumer
tout risque de perte ou de dommage en transit.
Si, suite à l’examen du produit à l’usine Polk ou chez le marchand agréé Polk Audio, il est déterminé que la défectuosité est imputable
aux matériaux d’origine ou à la main d’oeuvre au cours de la période de la garantie spécifiée, Polk Audio ou le revendeur Polk Audio, à
sa guise, réparera ou remplacera le produit sans frais additionnels et selon les conditions décrites ci-dessous.
Toute pièce ou produit remplacé devient la propriété de Polk Audio. Les produits réparés ou remplacés
sous la garantie vous seront expédiés francs de port dans un délai raisonnable.
Cette garantie n’inclut pas le service ou les pièces nécessaires à la réparation des dommages provoqués par accident, désastre, abus,
négligence, mode d'expédition ou emballage inadéquat, utilisation commerciale, tensions supérieures au maximum prescrit pour l’unité, aspect visuel du meuble non directement attribuable à un défaut de pièces d’origine ou de main d’oeuvre, ou par le service, la
réparation, ou toute modification du produit qui n’a pas été autorisé ou approuvé par Polk Audio. Cette garantie sera annulée si le
numéro de série sur le produit a été enlevé, altéré ou falsifié.
Cette garantie prend préséance sur toutes autres garanties énoncées. Si la défectuosité de ce produit est imputable aux pièces d’origine ou à la main d’oeuvre selon les conditions de la garantie exprimées ci-dessus, votre seul recourt sera la réparation ou le remplacement selon les conditions décrites ci-dessus.
Dans aucun cas Polk Audio, Inc. pourra-t-elle être tenue responsable pour tout dommage accessoire ou indirect cause par l’utilisation
ou par l’incapacité d’utilisation du produit, même si Polk Audio, Inc. ou un revendeur agréé Polk Audio, a été avisé de la possibilité de
tel dommage, ou pour toute réclamation par tout autre parti.
Certains états ne permettant pas l’exclusion ou la limitation des dommages indirects, les limitations
et exclusions exprimées ci-dessus pourraient ne pas s'appliquer dans votre cas.
Toutes les garanties tacites sur ce produit sont limitées à la durée de la garantie énoncée. Certains états ne permettant pas la limitation de la durée d’une garantie tacite, les limitations ci-dessus pourraient ne pas s’appliquer dans votre cas. Cette garantie vous accorde des droits légaux spécifiques; vous pourriez également avoir d’autres droits qui pourraient varier d’état en état.
Cette garantie s’applique seulement aux produits achetés au Canada, aux États-Unis d’Amérique et ses possessions, et dans les clubs
audio et d’échange des forces armées des É.U. et de l’OTAN. Les modalités et les conditions de garantie applicables aux produits
achetés dans d’autres pays sont disponibles chez les distributeurs agréés Polk Audio établis dans ces pays.
Customer Service Hours of Operation: Monday-Friday, 9AM-6PM EST polkcs@polkaudio.com 1312 Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
5601 Metro Drive
Baltimore, MD 21215
800-377-7655 (US & CAN, Outside US 410-358-3600)
www.polkaudio.com
Polk Audio is a DEI Holdings, Inc. Company. Polk Audio, Polk,
The Speaker Specialists and F/X are registered tradmarks of
Polk Audio, Inc.
Loading...