OXO Multibeam User Manual

USER MANUAL

Thank you for purchasing this product.

For your own safety, please read this user

manual carefully before you initially start-up

MULTIBEAM

TECHNICAL SPECIFICATIONS

18 full color + white

Sui table f or : indo or use IP 2 0
Volt age I nput : 10 0-240 VAC / (47 ~63)H z (230V / 5 0Hz - 0.6 7A)
Pow er Cons umpti on : 150W m ax

LED a mount : 1 8 pcs / RGB W 4 in 1, 18 x 8W
DMX c hanne l : 1 to 8 CH.

O

O

Wor kin g Stora ge Tempe rat ure : 0 / +40 C
Fus e : T3 .15 A L25 0V
Dim ensio ns (LxW xH) : 278 x 2 20.6 x 35 8mm
Wei ght : 4 .8Kg

Mul tiBea m - Manua l_EN_ FR_V6 .cdr P1 / 6 2 0111121 10: 32

SAFETY INSTRUCTIONS

Every person involved with the installation, operation and maintenance of this device has to :

• be qualified

• follow the instructions of this manual

• CAUTION ! Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric
shock when touching the wires !

• This device has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and
warning notes written in this user manual.

• IMPORTANT: Damages caused by the disregard of this user manual are not subject to warranty. The
dealer will not accept liability for any resulting defects or problems.

• Keep away from heaters and other heating sources !

• If the device has been exposed to drastic temperature fluctuation (e. g. after transportation), do not switch it
on immediately. The arising condensation water might damage your device. Leave the device switched off
until it has reached room temperature.

• Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the
power-cord from time to time.

• If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the
manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

• shields, lenses or ultraviolet screens shall be changed if they have become visibly damaged to such an
extent that their effectiveness is impaired, for example by cracks or deep scratches.

• Never let the power-cord come into contact with other cables ! Handle the power-cord and all connections
with the mains with particular caution !

• Make sure that the available voltage is not higher than stated in this manual.

• Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the
power-cord by the plug. Never pull out the plug by tugging the power-cord.

1) MO DE :
sel ect LED m ode, de tail se e

fig ure 1.

2) UP :
sel ect DMX a ddres s, prog ram

spe ed, dim mer val ue
clo ck-wi se dire ction .

3) DO WN :
sel ect DMX a ddres s, prog ram

spe ed, dim mer val ue coun ter
clo ck-wi se dire ction .

2 3

• During the initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective.

• DANGER OF BURNING ! Never touch the device during the operation ! The housing heats up to the
housing temperature TSURFACE.

• Don’t switch the device on and off in short intervals as this would reduce the lamp’s life.

• HEALTH HAZARD ! Never look directly into the light source, as sensitive persons may suffer an epileptic
shock (especially meant for epileptics)

• Always disconnect from the mains, when the device is not in user or before cleaning it.

• Please note that damages caused by manual modifications on the device or unauthorized operation
byunqualified persons are not subject to warranty.

• Keep away children and amateurs from the device !

• There are no serviceable parts inside the device. Maintenance and service operations are only to be
carried out by authorized dealers.

OPERATION INSTRUCTIONS

1) The system has DMX online/stand-alone mode. DMX online mode can link up with each other and
con trolled by DMX con troller; The stand-alone has some functions, such as dimmer, change
program, sound control.

2) If the slave links up with the master and also connects DMX controller, the master can automatically
identify and turn off the sending data function of the mater, the slave receive the DMX signals from
controller.

3) OXO function test: under manual mode and the DMX signals is present, the menu automatically
jump to DMX 8CH, when cut off the DMX signals, the menu back to original manual mode.

4) when there are no DMX online mode and DMX signals, the LCD display "NO DMX SIGNAL”

5) The device has the function of saving present running state, and run the last mode under power off
when re-turn on.

6) The device has the function of fan controlling, the fan will stop when the LED is lightless; the fan will
automatically stop after 30s, when the LED is from light to lightless.

FUNCTION DESCRIPTION

USER INSTRUCTION - MULTIBEAM LED FCW