OvisLink SI102 User Manual

Adding to Remove from Z-Wave

Table of Content

Network ........................................................................................................ 1

Z- WaveTM Notification ...................................................................................................................................... 2

Z-WaveTM Message Report ................................................................................................................................. 2

* Motion Report: ......................................................................................................................................... 3

* Tamper Report: ......................................................................................................................................... 3

* Timing Report: ......................................................................................................................................... 3

Power Up Procedure ............................................................................................................................................ 3

* Battery Power Check ................................................................................................................................. 3

* PIR Warm Up ........................................................................................................................................... 3

* NWI ........................................................................................................................................................ 4

* Wake ....................................................................................................................................................... 4

Security Network ................................................................................................................................................ 4

Operation Mode .................................................................................................................................................. 4

Choosing a Suitable Location ................................................................................................................................ 4

Z-Wave Configuration Settings ............................................................................................................................. 5

Z-Wave Supported Command Class ....................................................................................................................... 5

Specifications ..................................................................................................................................................... 8

FCC Interference Statement .................................................................................................................................. 9

Warning ............................................................................................................................................................. 9

SI-102

SI-102-FCC

Motion Sensor

The motion sensor SI-102 has PIR function, based on Z-Wave This device is a Security Enabled Z-Wave Plus Product. Z-WaveTM is a wireless communication protocol designed for home automation, specifically to remotely control applications in residential and light commercial environments. The technology uses a low-power RF radio embedded or retrofitted into home electronics

technology.

devices and systems, such as lighting, home access control, entertainment systems and household appliances.

This product can be included and operated in any Z-WaveTM network with other Z-WaveTM certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. The device adopts the Z-WaveTM 500 series chip, when your Z-Wave

network system is all made by

Z-WaveTM 500 series devices. The network system will have the advantages as below.

 Concurrent multi-channel support reduces external interference.  Better RF range, improve about 10 meters in indoor.  Support 100 Kbps transmit speed, speed up communication.

Adding to Remove from Z-Wave

Network

There are two keys in the device, one is tamper key, another is a button. Button can add, remove, reset or association from Z-WaveTM network. In the first time, add the device into the Z-WaveTM network. First, make sure the primary controller is in the add mode. And then power on the device, just take out the insulation Mylar in the back side of the device. The device will auto start the NWI (Network Wide Inclusion) mode. And it should be included in 5 seconds. You will see the LED light ON one second.

Notice: Including a node ID allocated by Z-WaveTM Controller means “Add” or “Inclusion”. Excluding a node ID allocated by Z-Wave

Controller means “Remove” or “Exclusion”.

Functi

on Description

Note: The device supports 2 groups.

Add

Remove

Reset

Association

1. Have Z-WaveTM Controller entered inclusion mode.

2. Pressing button once to enter the inclusion mode.

3. After add successful, the device will wake to receive the setting command from Z-Wave controller about 20 seconds.

1. Have Z-WaveTM Controller entered exclusion mode.

2. Pressing button once to enter the exclusion mode. Node ID has been excluded.

Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.

1. Pressing button for about 5 seconds.

2. IDs are excluded and all settings will reset to factory default.

1. Have Z-WaveTM Controller entered association mode.

2. Pressing button one time to enter the association mode.

The group 1 is for receiving the report message, like triggered event, temperature, illumination etc. The group 2 is for light control, the device will send the “Basic Set” command to this group. And each group support 8 nodes maximum.



Failed or success in add/remove the node ID can be viewed from Z-WaveTM Controller.

Notice 1: Always RESET a Z-WaveTM device before trying to add it to a Z-WaveTM network

Notice 2: When the device into NWI mode, the sensor functionality will useless. The NWI mode will timeout

after 30 seconds. You can press the button one time to abort the NWI mode.

Z- WaveTM Notification

After the device adding to the network, it will wake-up once per day in default. When it wake-up it will broadcast the “Wake Up Notification” message to the network, and wake-up 10 seconds for receive the setting commands. The wake-up interval minimum setting is 30 minutes, and maximum setting is 120 hours. And the interval step is 30 minutes. If the user wants to wake-up the device immediately, please remove the front cover, and press the button once. The device will wake-up 10 seconds.

Z-WaveTM Message Report

When the PIR motion triggered, the device will report the trigger event and also report the battery status. In default the device will using Notification Report to represent the trigger event, it can be changed to Sensor Binary Report by setting the configuration NO. 7 Bit4 to 1.

+ 7 hidden pages