Outline TFive, TSeven, TNine, TEleven User Manual

2 CHANNEL POWER AMPLIFIER

The Sound of Big Ideas

This page left intentionally blank

Outline s.r.l. - Via Leonardo da Vinci, 56 - 25020 Flero (Brescia) - Italy

Tel. [phone] Fax [phone] — Web Site: www.outline.it E-Mail: [e-mail]

The Sound of Big Ideas

Table of contents

Important safety instructions

ntroduction

Chapter 1: Installation and operation

Chapter 2: Setup and settings

Chapter 3: Protection

Chapter 4: User maintenance

Chapter 5: Warranty
Chapter 6: Assistance
Chapter 7: Technical notes

................................................................................................................................2

................................................................................................................................................................2

Safety rules.......................................................................................................................................................................3

Speaker damage..............................................................................................................................................................3

Speaker output shock hazard...........................................................................................................................................3

I ......................................................................................................................................................................4

More sound and less weight.............................................................................................................................................4

Superior Sound-Sonic Accuracy.......................................................................................................................................4

Totally Digital with High Reliability........................................................................................................................................................4

The Best amplifier for Your Mains........................................................................................................................................................4

The T Series........................................................................................................................................................................................4

The Show Always Goes On..............................................................................................................................................4

...........................................................................................................................................................5

1.1 Unpacking...................................................................................................................................................................5

1.2 Mounting.....................................................................................................................................................................6

1.3 Operating precautions................................................................................................................................................6

1.4 AC Mains connection..................................................................................................................................................6

1.5 Connecting Inputs........................................................................................................................................................7

1.6 Connecting Outputs.......................................................................................................................................................................8

1.7 Connecting Remote Control..........................................................................................................................................................9

1.8 AUX Input CH1/CH2.............................................................................................................................................................................................10

1.9 Alarm CH1/CH2....................................................................................................................................................................................................10

1.10 AES/EBU Input.....................................................................................................................................................................................................10

.....................................................................................................................................................................11

2.1 Introduction....................................................................................................................................................................................11

2.2 The Main screen............................................................................................................................................................................11

2.3 The main menu............................................................................................................................................................................12

2.3.1 Output attenuation......................................................................................................................................................................13

2.3.2 Gain/Sensitivity.............................................................................................................................................................................13

2.3.3 Input select........................................................................................................................................................................14

2.3.4 Max output voltage............................................................................................................................................................14

2.3.5 Max mains current............................................................................................................................................................14

2.3.6 Clip limiter CH1-CH2........................................................................................................................................................14

2.3.7 Gate CH1-CH2.................................................................................................................................................................15

2.3.8 Mute at power on..............................................................................................................................................................15

2.3.9 Idle Mode..........................................................................................................................................................................15

2.3.12 Bar meters......................................................................................................................................................................15

2.3.13 Output meters.................................................................................................................................................................15

2.3.14 Temperature....................................................................................................................................................................16

2.3.15 Mains meters..................................................................................................................................................................16

2.3.18 Hardware info.................................................................................................................................................................17

2.3.19 Hardware monitor...........................................................................................................................................................17

2.3.20 LCD contrast....................................................................................................................................................................18

2.3.21 Set Keylock code.............................................................................................................................................................18

2.3.23 Service............................................................................................................................................................................18

2.3.24 The Smartcard function..................................................................................................................................................19

...............................................................................................................................

..................................................20

3.1 Turn-On/Turn-Off muting..............................................................................................................................................................20

3.2 Short circuit protection.................................................................................................................................................................20

3.3 Thermal protection.......................................................................................................................................................................20

3.4 DC fault protection.......................................................................................................................................................................20

3.5 Input/Output protection................................................................................................................................................................20

....................................................................................................................................................................21

4.1 Cleaning.......................................................................................................................................................................................21

........................................................................................................................................................................................21

4.3 Error codes................................................................................................................................................................................21

...................................................................................................................................................................................22

................................................................................................................................................................................22

........................................................................................................................................................................22

7.1 General Dimension..............................................................................................................................................................................22

7.2 Block diagram...............................................................................................................................................................23

Approvals

Warning Notice................................................................................................................................................................2

2.3.10 DSP Settings...................................................................................................................................................................15

2.3.11 Ethhernet Settings...........................................................................................................................................................15

2.3.16 Amplifier Name................................................................................................................................................................16

2.3.17 Local preset.....................................................................................................................................................................16

2.3.22 Menu locking...................................................................................................................................................................18

4.2 Dust removal

4.4 Service................................................................................................................................................................................21

7.3 Technical specifications...............................................................................................................................................................24

Professional amplifiers

T Series

Outline s.r.l. - Via Leonardo da Vinci, 56 - 25020 Flero (Brescia) - Italy

Tel. [phone] Fax [phone] — Web Site: www.outline.it E-Mail: [e-mail]

1

E

Important safety instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO N OT OPEN

!

CAUTION:

SAFEGUARDS: Electrical energy can perform many useful functions. This unit has been engineered and
manufactured to assure your personal safety. Improper use can result in potential electrical shock or fire
hazards. In order not to defeat the safeguards, observe the following instructions for its installation, use and
servicing.

To reduce the risk of electric shock, do not remove the cover. No user-serviceable parts inside. Refer

servicing to qualified service personnel.

KEEP THIS INSTRUCTIONS

The Outline T Series is installed according to the Canadian Electrical Code or National Electrical Code, as applicable.

T Eleven - T Nine - T Seven
This equipment has been tested and found to compliant by Competent Body (Directive 89/336/EEC-EMC) pursuant to
the product family standard for audio professional use:
EN 55103-1 and EN 55103-2 standard ); EN61000-3-2,EN61000-3-3.
Conducted Emissions : Electromagnetic Ambient E1, E2, E3 / Class B
Radiated Emissions : Electromagnetic Ambient E1, E2, E3 / Class B
In a domestic environment this product may cause radio interferences in which case the user may be required to take
adequate measures.
This equipment has been tested and found to comply by Notified Body (Directive 2006/95/EEC L.V) pursuant to the
audio apparatus safety requirements: Standard EN 60065.

(*) T Five pending

T Five(*)
This equipment has been tested and found to compliant by Competent Body (Directive 89/336/EEC-EMC) pursuant to
the product family standard for audio professional use:
EN 55103-1 and EN 55103-2 standard ); EN61000-3-2,EN61000-3-3.
Conducted Emissions : Electromagnetic Ambient E1, E2, E3 / Class B
Radiated Emissions : Electromagnetic Ambient E4, E5 / Class A
Radiated Emissions : Electromagnetic Ambient E1, E2, E3 / Class B (**)
In a domestic environment this product may cause radio interferences in which case the user may be required to take
adequate measures.
(**) Additional round snap ferrite (of at least 145 Ohm @ 25 Mhz and 265 Ohm @ 100MHz) on Output cables and
Mains Cord allows to fulfill Electromagnetic Ambient E1, E2, E3 / Class B on radiate Emissions.
This equipment has been tested and found to comply by Notified Body (Directive 2006/95/EEC L.V) pursuant to the
audio apparatus safety requirements: Standard EN 60065.

Approvals

Warning notices

LOCATION: Install the amplifier in a well-ventilated location where it will not be exposed to high temperature or

humidity.
Do not install the amplifier in a location that is exposed to direct rays of the sun, or near to hot appliances or radiators.
Excessive heat can adversely affect the cabinet and internal components. Installation of the amplifier in a damp or
dusty environment may result in malfunction or accident.

Outline s.r.l. - Via Leonardo da Vinci, 56 - 25020 Flero (Brescia) - Italy

Tel. [phone] Fax [phone] — Web Site: www.outline.it E-Mail: [e-mail]

2

The Sound of Big Ideas

This device must be powered exclusively by earth connected mains sockets in electrical networks compliant to the IEC 364
or similar rules.
Is absolutely necessary to verify this fundamental requirement of safety and, in case of doubt, require an accurate check by
a qualified personnel.
The constructor cannot be considered responsible for eventual damages caused to persons, things or data for the missing
of accurate earth link.

Before powering this device verify that the amplifier is supplied with the correct voltage rating.
Verify that your mains connection is capable to satisfy the power ratings of the device.
Do not spill water or other liquids into or on the unit.
Do not use this unit if the electrical power cord is frayed or broken.
Do not remove the cover. Removing the cover will expose you to potentially dangerous voltage.
No naked flame sources such like lighted candles should be placed on the amplifier.
Provide sectioning breaker between mains connections and apparatus. Suggested device is 32A/250Vac, C or D
curve, 10KA
The inlet power supply cord plug is useful as disconnection device
The power cord type is LAPP CABLE OLFLEX191 3G6 / SJT 3XAWG10 SALCAVI (Bahoing SJT 3x16AWG or I­sheng SGIS 3G1,5mmq for T Five)

Contact the authorized center for ordinary and extraordinary maintenance

·

·

·

·

·

·

·

·

·

.

The Outline T Series amplifiers are among the most powerful professional amplifiers available and are capable of producing
much more power than many loudspeakers can handle. It is the user's responsibility to use suitable speakers with the
amplifier and to use them in a sensible way that will not cause damage. Outline will not be responsible for damaged
speakers. Consult the speaker manufacturer for power-handling recommendations. Even if you reduce the gain using the
amplifier's front panel attenuation controls, it is still possible to reach full output power if the input signal level is high
enough.
A single high-power crescendo can damage high-frequency drivers almost instantaneously, while low-frequency drivers can
usually withstand very high, continuous power levels for a few seconds before they fail. Reduce power immediately if you
hear any speaker "bottoming out" - harsh pops or cracking distortion that indicate that the speaker voice coil or diaphragm
is striking the magnet assembly. Outline recommends that you use amplifiers of this power range for more headroom
(cleaner sound) rather than for increased volume.

A Outline T Series amplifier is capable of producing hazardous output voltages. To avoid electrical shock, do not touch any
exposed speaker wiring while the amplifier is operating.

This manual contains important information on operating your T Series amplifier correctly
and safely. Please read it carefully before operating your amplifier. If you have any questions,
contact your Outline dealer.

Safety Rules

Speaker output shock hazard

Speaker damage

Precautions regarding installation

WARNING:

Placing and using the amplifier for long periods on heat-generation sources will affect performances. Avoid placing the
amplifier on heat-generating sources. Install this amplifier as far as possible from tuners and TV sets. An amplifier installed
in close proximity to such equipment may cause noise or degradation of the picture.

To prevent fire or electric shock:

The ventilation should not be impeded by covering the ventilation openings with items such newspapers, table­clothes, curtains etc.
Do not expose this equipment to rain or moisture.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be
placed on the apparatus”.

·

·

·

Professional amplifiers

T Series

Outline s.r.l. - Via Leonardo da Vinci, 56 - 25020 Flero (Brescia) - Italy

Tel. [phone] Fax [phone] — Web Site: www.outline.it E-Mail: [e-mail]

3

E

Introduction

Outline is a leading company in the field of high efficiency audio power management. The totally new DIGAM (DIGital
AMplifier) technology has changed the way the world looks at professional audio amplification. No other amplifiers
come close for applications demanding high power and long term reliability. Thanks to amazing reductions in heat
output along with reductions in weight and the specific high output power, T Series amplifiers can be used in an
unlimited range of applications such as concert touring, opera houses, theatres, churches, cinema, theme parks,
television sound stages and industrial applications.

More sound and less weight

Totally Digital with High Reliability

Compared to a conventional amplifier, Outline T Series technology offers very high efficiency and delivers more power
to the loudspeakers with much reduced heat dissipation. This greater efficiency enables dimensions, weight and power
consumption to be reduced. The output stages of the amplifiers typically run at 95% efficiency, dissipating only 5% of
the input energy as heat.

One of the most interesting characteristics is that efficiency is almost independent of output level. Conventional
amplifiers achieve their best efficiency only at full rated power output. Since standard music has an average power
density of 40% of the maximum level, conventional amplifiers can easily generate 10 times more heat than T Series
for the same volume of sound.

Crystal-clear highs, and a tight, well-defined low end: the most accurate reproduction of an audio signal. Patented
design features ensure very high performance in parameters such as distortion, frequency response, slew rate, power
bandwidth and dumping factor.

The T Series is based on PWM technology that has been used for 30 years or more in power supplies and inverters.
PWM provides high reliability, small size, low weight and high efficiency. A PWM converter works as a high frequency
sampler, converting the variable amplitude (audio) signal into an impulse sequence with average value equal to the
audio input.
T Series amplifiers use very high sampling frequencies to obtain high performances across the audio band.

Outline adopt Power Factor Correction. This feature ensures that a predominantly resistive load is presented to mains,
minimizing current distortion and voltage/current displacement This leads to much improved performance of the
amplifier at high levels of output and avoids mains-voltage collapses, typical of standard and switching power
supplies. Another great advantage of this technology is that its performance is, to a large extent, independent of mains
voltage. The rated output power does not vary with load/line conditions.

T Series has many advanced features, Digital control of many parameters, adjustable maximum mains consuption,
selectable digital presets and a graphic display that shows detailed information of the status of the amplifier. You can
appreciate the functionality of these and a lot of other features by reading this manual

T Series is completely protected against every possible error in operation and is designed to work under every
condition. It gives you maximum power with maximum safety and increases long-term reliability. Anticipating potential
problems at the design stage means your show always goes on!

Superior Sound-Sonic Accuracy

The Best Amplifier for Your Mains

The T Series

The Show Always Goes On

carefully.

Outline s.r.l. - Via Leonardo da Vinci, 56 - 25020 Flero (Brescia) - Italy

Tel. [phone] Fax [phone] — Web Site: www.outline.it E-Mail: [e-mail]

4

The Sound of Big Ideas

1 Installation and operation

1.1 Unpacking

Carefully open the shipping carton and check for any noticeable damage; t

Every Outline amplifier is completely tested and inspected before leaving the factory and should arrive in perfect
condition. If you find any damage, notify the shipping company immediately. Be sure to save the carton and all packing
materials for the carrier's inspection.

he figure below shows the exploded view of the

packing.

figure 1.1

Manual

Amplifier

Mains cable

Professional amplifiers

T Series

Outline s.r.l. - Via Leonardo da Vinci, 56 - 25020 Flero (Brescia) - Italy

Tel. [phone] Fax [phone] — Web Site: www.outline.it E-Mail: [e-mail]

5

E

1.3 Operating Precautions

Make sure the AC mains voltage is correct and is the same as that printed on the rear of the amplifier. Damage caused
by connecting the amplifier to improper AC voltage is not covered by the warranty. Make sure the power switch is off
before making any input or output connections.
It is always a good idea to have the gain controls muted during power-up to prevent speaker damage if there is a high
signal level at the inputs.
Whether you buy them or make them, use good-quality input and speaker cables. Most intermittent problems are
caused by faulty cables. Use good-quality connectors and wire, along with good soldering technique, to ensure
troublefree reliability.

1.4 AC Mains connection

The AC Main connection is made via the CPC type connector (IEC20Afor T Five) on the rear side of the panel. The
figure below shows the connection to the amplifier. Be sure that your AC mains power source has the requirements
indicated in this manual.

Is important to connect the ground for safety, do not use adapters that disable the ground.

The T Series amplifier has an automatic power factor correction system for a perfect mains
network interface. The amplifier is a resistive load for the mains network, minimizing the reactive power and the
harmonic distortion on the current. The system allows performance to be maintained even in circumstances of varying
the mains voltage.

1.2 Mounting

All T Series amplifiers are previewed for the standard 19" rack mounting; there are four front panels holes and fout rear
lateral holes. The amplifiers must be fixed into rack in both sides, back and frontal, to avoid mechanical damages. Your
amplifier uses a forced-air cooling system to maintain a low, even operating temperature. Drawn by an internal fan, air
enters through the slots in the front panel and courses over and through components. The T Series amplifiers feature
an "intelligent" variable-speed DC fan which is controlled by heat sink temperature sensing circuits: the fan speed will
increase only when the temperature of either heat sink requires it, which keeps fan noise to a minimum and helps cut
dust accumulation inside. Under extreme thermal load, the fan will force a very large volume of air through the heat
sinks. If either heat sink gets too hot, its sensing circuit will reduce the output power. If the amplifier overheats, another
sensing circuit shuts down its circuit to cut off power until it cools to a safe temperature.
The exhaust cooling air is forced out through the rear of the chassis (see figure 1.2.1), so make sure there is enough
space around the sides of the amplifier to allow the air to escape. If it is rack mounted, make sure the exhaust air can
flow without resistance. If you are using a rack with closed backs, there must be at least one standard rack space of
opening in the front of the rack for every four amplifiers. Amplifiers may be stacked directly on top of each other (no
space needed between units), starting from the bottom of the rack.

figure 1.2.1

air flow

figure 1.4.1

T Five only

MAINS

T

U

R

N

T

O

L

O

C

K

CAUTION!RISK OF ELECTRIC SHOCK: DO NOT OPEN

Vac GND

other T models

open the lock
and insert the plug

lock the plug

MAINS

GROUND

Outline s.r.l. - Via Leonardo da Vinci, 56 - 25020 Flero (Brescia) - Italy

Tel. [phone] Fax [phone] — Web Site: www.outline.it E-Mail: [e-mail]

6

The Sound of Big Ideas

1.5 Connecting Inputs. Input connections are made via the 3-pin XLR-female type or 1/4" phone Jack connectors on the

rear side of the amplifier. The polarity is shown in figure 1.5.1.

The figure below shows the connection of analog input for balanced and unbalanced line. You can use both configuration,
but you must consider that unbalanced long line can introduce noise in the audio system. The Link switch located in the
rear panel is for direct paralleling the rear input connectors. You can use the remaining input connector to carry signal to
other amps.

IN(-)
IN(+)

GND

Balanced input

IN(+)

SHIELD

Unbalanced input

/

figure 1.5.2

figure 1.5.1

OUT2

IN2 IN1

OUT1

T

U

R

N

T

O

L

O

C

K

T

U

R

N

T

O

L

O

C

K

“WARNING

Toreduce The Risk of Fire

orElectric Shock, do not

Exposethis Apparatus

toRain or Moisture”

LINK

ON OFF

CLASS2 WIRING

pin2 - IN(+)

pin3 - IN(-)

pin1 - GND

IN(+)

IN(-)

GND

For T Five, the input connections are showed in the figure below; analog input for balanced and unbalanced line is also
available for this models.

pin2 - IN(+)

pin3 - IN(-)

pin1 - GND

pin 2 - IN(+)

pin1 - GND

pin 3 - IN(-)

signal source input
XLR female connector

signal source output
XLR male connector

XLR female

XLR male

T Five model

Professional amplifiers

T Series

Outline s.r.l. - Via Leonardo da Vinci, 56 - 25020 Flero (Brescia) - Italy

Tel. [phone] Fax [phone] — Web Site: www.outline.it E-Mail: [e-mail]

7