Outback Saracen, Sapphire, RC4341P, Magnum 3 Assembly Manual

Photogr aphs are not to scale.
Specif ic ati ons su bj ect to chang e
without prior notice.

Assembly and Operating Instructions for Outback®

Saracen 2 Burner Gas BBQ

WARNING

• For outdoor use only. Not for commercial use.

• Read in structions before using the appliance. Failure to follow instructions could

result in death, serious bodily injury, and/or property loss.

• Warning: accessible parts may be very hot. Keep young children and pets away.

• Do not move the appliance during use.

• Turn off the gas supply at the gas bottle after use .

• Any modification of the appliance, misuse, or failure to follow the instruct ions may be

dangerous and will invalidate your warranty. This does not affect your statutory rights.

• Retain these instructions for future reference.

• Leak test annually, and whenever the gas bottle is removed or replaced. Check that the

hose connections are tight and leak test each time you reconnect the gas bottle.

• For Flare-up control please refer to the ‘OPERATION’ section of this manual.

FOR YOUR SAFETY

If you sm ell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open barbecue lid or hood.

4. If odour continues, discontinue use and
contact your local dealer.

FOR YOUR SAFETY

1. Do not store or use petrol or other flammable
vapours or liquids in the vicinity of this or any
other appliance.

2. A gas bottle not connected for use shall not be
stored in the vicinity of this or any other
appliance.

0359

THG2216

2

Parts List

Quantities vary according to model purchased. Specifications subject to change without prior notice. For
more details on hardware, please see ‘Hardware Reference Diagram’.

CODE PART QTY

Outback®

Saracen 2 Burner Gas BBQ

HOOD

A1

Hood (Pre-Assembled to B ody)

1



A2 Hood Handle 1



A3 Hood Handle Spacers 2



A4 Heat Indicator 1



A5 Warming Rack 1



BODY

B1 Barbecue Body 1



B2 Burner 2



B3 Cross Channel 1



B4 Control Panel 1



B5 Knob 2



B6 Ignition Pushbutton 1



B7 Flame Tamer 2



B8 Cooking Grill 2



B9 Hose and Regulator Ass embly 1



B10 Drip Tray 1



B11 Drip Tray Left Bracket 1



B12 Drip Tray Right Bracket 1



TROLLEY

C1 Left Side Shelf 1



C2 Right Side Shelf 1



C3 Tool Hook 1



C4 Left Front Leg 1



C5 Left Rear L eg 1



C6 Right Front Leg 1



C7 Right Rear Leg 1



C8 Beer Bottle Opener 1



C9 Front Screen 1



C10 Trolley Base 1



C11 Leg Endcap 2



C12 Axle 1



C13 Wheel 2



C14 Hubcap 2



HARDWARE

D1 M5x15 Bolt 4



D2 Washer 4



D3 M5 Nut 4



D4 M6x15 Bolt 11



D5 M6 Nut 10



D6 ST4.0x10 Screw 6



D7 M6x40 Bolt 8



D8 M6x75 Bolt 8



D9 Locknut 2



 Pre-Assembled Component

3

Parts Diagrams

Quantities vary according to model purchased. Specifications subject to change without prior notice. For
more details on hardware, please see hardware pack page.

A1

A2

A3

A4

B2

B4

B5 B6

A5

B7

B8

B3

B1

C11

B12 B10

C1 C2

C3

C8

C7 C6

C9

C13

C10

C4 C5

C14

C12

D9

B11

B9

4

Hardware Reference Diagram

Specifications subject to change without prior notice.

D1,D2,D3

D4 D4,D5

D6

D8

D5,D7

5

Attach the Legs (C4,C5,C6,C7) to the Trolley Base (C10) using the M6x40 Bolts (D7x8pcs) and
M6 Nuts (D5x8pcs), as shown.

Note: The left legs are shorter than right legs.

2

Assembly

IMPORTANT!

• TOOLS NEEDED FOR ASSEMBLY: Medium size flat blade or Phillips/Crosspoint screwdriver,

adjustable spanner or metric spanner set.

• Remove any internal components or packaging from the barbecue body.

• Whilst every care is taken in the manufacture of this product, care must be taken during assembly in

case sharp edges are present.

• Please read the Important Information section carefully before assembly and use of your

barbecue.

Unscrew the Locknuts (D9) from both ends of the Axle (C12). Slide the axle through the
corresponding holes in the left legs. Slide the Wheels (C13) over each end of the axle. Secure the
wheels into place with the locknuts. Place the wheel Hubcaps (C14) onto the outsides of the
wheels.

C14

D9

C12

C13

C7

C6

C4

C5 D7 D5

C10

1

A

B

A

B

6

4

3

Insert M6x75 Bolts (D8x8pcs) through the trolley legs, While holding the barbecue body into
position (2 people required), screw the bolts into the barbecue body as shown.

CAUTION! Care must be taken to ensure the hood or lid does not fall open unexpectedly or
becomes damaged when it is set on the ground.

Attach the Tool Hook (C3) to the Right Side Shelf (C2) using M6x15 Bolts (D4x2pcs) and M6 Nut
(D5x2pcs), as shown.

LEFT

RIGHT

D8

C3 D4

C2

D5