Blinking On continuously
The controller is The valve is competely open.
increasing the heat. Not enough heat in the boiler.
(Valve is opening)
The controller is The valve is closed. In the
decreasing the heat summer when no heat is
(Valve is closing) needed this lamp may always
be on.
The unit is operating.
For example, read control curve C as follows:
CONTROL CURVES
* If the room temperature is always too cool, turn knob
B in the + direction.
* If the room temperature is always too warm, turn
knob B in the - direction.
One step of the scale of knob B changes the outgoing
water temperature by 4°C, corresponding to about 1°C
in the room temperature.
Select a house-specific control curve
with knob A.
Set the basic setting according to the
table below.
BOILER OR
ACCUMULATOR
HEATING
NETWORK
BOILER OR
ACCUMULATOR
HEATING
NETWORK
Heating characteristics of the building Position of knob A
Well-insulated house (radiator heating) C...D
House with poor heating characteristics E... F
House with a floor heating system A... B
C
B
D
E
A
F
Curve C is selected in this example. If the room
temperature goes down when the weather gets cold,
select a steeper curve. If the room temperature goes up,
select a lower curve. A suitable curve for your house may
be between the plotted curves.
If the room temperature is even, but
it is too cool or warm, make a fine
adjustment with knob B.
+
NOTE ! Changes in the settings are felt quite slowly.
Wait a few hours before making additional adjustments.
–
Knob B raises and
lowers the selected
curve.
Select the steepness of
the curve with knob A
CBD
E
AF
The OUMAN controller contains a wide range of
control curves that are designed to respond to very
different kinds of heating conditions. It also has low
curves suitable for houses with floor heating.
C
80
100
60
40
20
Outgoing water temperature
Outdoor temperature
20100-10-20-30
°C
When it is -20°C, the outgoing water is 50°C
When it is 10°C, the outgoing water is 44°C
When it is 0°C, the outgoing water is 37°C
INDICATOR LAMPS
MANUAL OPERATION
+–
A
+
–
ON
LED
If the green ON indicator lamp is not on, check that
the transformer is plugged in and the transformer lead
is connected. Check the line voltage.
B
MIN - MAX - LIMITS
The settings located behind the
instruction booklet under the clear
cover are usually set only when the
controller is taken into use the first time.
The minimum limit knob sets the lowest
allowable outgoing water temperature
(if sufficient heat is available).
The maximum limit knob sets the
highest allowable outgoing water
temperature. This is especially beneficial
in floor heating systems, where overly
hot water may cause damages.
OUMAN
OUMAN
OUMAN
OUMAN
OUMAN OUMAN
OUMAN OUMAN
OUMAN automatically adjusts the
temperature of the water entering the
network. The heat requirement varies
according to the outdoor
When the weather gets cooler, OUMAN
releases just enough heat into the network
to maintain an even room
temperature.
OPERATING PRINCIPLE
The OUMAN 80 can also be used manually. Unplug the
transformer to disconnect the operating voltage. Press
the button on the bottom right all the way down while
turning the valve to the desired position with the manual
control lever.
NOTE ! If you wish to disconnect the controller for a
longer period (e.g., in summer), disconnect the operating
voltage (13 VAC) connector from the controller. The
clock battery will also be disconnected to avoid unnecessary
battery drainage (battery life = about 180 days). The
battery is a backup power supply for the clock and
programming during power shortages.
FINE ADJUSTMENT
BASIC SETTING
EH-80
BASIC SETTING, KNOB A
If the room temperature goes down when the
weather gets colder, select a steeper curve
and vice versa.
C
B
D
E
A
F
80
100
60
40
20
Outdoor temperature
20
10
0-10
-20
-30
°C
OPERATING INSTRUCTIONS
EH-80
EH-80
FINE ADJUSTMENT, KNOB B
If the room temperature is always too cool or
warm, turn knob B in the desired direction;
+ raises, - lowers the temperature.
Outgoing water temperature
EH-80
EH-80 EH-80
EH-80 EH-80
OUMAN
OUMAN
The degree of room compensation, the
compensation ratio, can be adjusted with
the COMP knob.
If the room temperature deviates from
the TMR/P set value, the TMR/P adjusts
the outgoing water temperature by a
ratio of the deviation set with the Comp
knob. These examples assume the
outdoor sensor is connected.
You can temporarily by-pass the timer program as follows:
Press and hold until the desired state is displayed.
Repeating this procedure will change the state. The next
programmed time will switch the forced control state off.
If you wish to permanently use forced control, press
again until the display shows .
TIMER
TO SET THE DROP TIMES
TO SET THE TIME
VACATION FUNCTION
OPTIONAL EQUIPMENT
4
OUMAN can be equipped with a timer
that drops the room temperature for
desired periods (e.g., at night or on
weekends). The timer is easy to install
later.
Set the drop in the
temperature of the outgoing
water with this knob. The
numbers indicate the number
of degrees the temperature will be
dropped. General guide: a 4°C drop in the
water temperature corresponds to a 1°C drop in the
room temperature.
NOTE! If the room compensation unit TMR/P is in use,
double the temperature drop setting. This will take into
account the compensation effect of the TMR/P.
Press Display Press Note!
TO CLEAR THE PROGRAMS:
To clear the programs in the timer:
Press and hold and simultaneously.
1234567
PROG
1234567
The number indicates the amount
of free program positions.
Select the desired combination
of days when the temperature
drop should start.
Set the start time for the
temperature drop: hour ...
... and minutes.
Acknowledge .
Set the end time for the
temperature drop: hour ...
... and minutes.
Acknowledge .
Now you can program a new temperature drop period.
Return to the normal state by pressing twice.
Press Display Press Note!
1234567
Set the hour.
Set the minutes.
Acknowledge . Time OK.
SUMMER/WINTER TIME DIFFERENCE:
Press and hold . The clock will automatically
move ahead or back one hour.
Summer time is being displayed
Select a day. 1=Mon,
2=Tue, 3=Wed, etc.
When the timer is switched on, all the symbols in the
display will blink. Follow the procedure shown below.
Meaning of symbols: Press once Press repeatedly until the
desired state is displayed
Press Display Press Note!
Set the length of the vacation
period
(1... 99 days).
Set the temperature state during
the vacation.
1 = temperature drop
0 = normal temperature
Acknowledge .
When the timer arrives at the vacation function time, the
symbol will be displayed.
If you do not press acknowledgement , the timer will
return to the basic state. You can start programming
again.
Set the number of days after
which the vacation function
should start (0... 14 days).
The vacation function lets you program a temperature
drop period that begins immediately or later (0 ...14
days). The temperature drop period can last 1... 99
days.
The display now shows the correct time and the colon
between the numbers is blinking. The programmed
temperature drop period is darkened.
0 = normal
temperature (the
temperature is not
dropped)
24
12
618
21
3
15
9
1 = The temperature is dropped
TO BROWSE A PROGRAM:
When the display shows PROG, you can browse through
a program in the timer by repeatedly pressing .
TO ADD A PROGRAM:
The timer must be in the PROG state. Press
until is displayed, then begin
programming a new temperature drop period.
1234567
1 4
Manufacturer:
OUMAN OY
KEMPELE, FINLAND
Select the desired room temperature with the TMR/P
knob. 21°C is in the middle. Each step of the scale equals
1°C. If the room temperature deviates from the set
temperature, the TMR/P automatically adjusts the
outgoing water temperature.
Example 1. The COMP knob is in position 4. If the room
temperature drops 1,5°C, the TMR/P will raise the
outgoing water temperature by 4 x 1,5 = 6°C.
Example 2. The COMP knob is in position 2. If the room
temperature rises 4°C, the TMR/P will lower the
outgoing water temperature by 2 x 4 = 8°C.
ONLY ROOM COMPENSATION
OUMAN can be connected as a room-controlled outgoing
water controller. (Disconnect the outdoor sensor.) Set
the room temperature with the TMR/P knob. If the delay
before the radiator temperature reacts to a change in
room temperature is too long, increase the COMP ratio.
1
4
2
1
3
3
3
3
2
2
2
2
4
4
1
2
1
3
3
2
4
2
3
3
2
1
3
4
2
3
3
0
1
4
4
0
2
2
0
p
The OUMAN EH 80 can be equipped with an optional room
compensation unit, TMR/P. It improves temperature control
in special conditions such as:
* windy weather (the house tends to get cooler)
* the house is warmed by
a fireplace, brick oven, etc.
* the house has large
windows on the south side,
and the house gets warm
on sunny spring days
regardless of cold weather.
Install the TMR/P in a
central place in the house.
ROOM COMPENSATION TMR/P
PROG
FORCED CONTROL
KS/80
EH-80
C
Loading...