Otto Bock TaiLor Made 1T01 Quick Manual

Download

Page 1

TaiLor Made

Foot Quick Guide

for

Ottobock

The 1T01 TaiLor Made foot has now HealthCare Products GmBH for following knees:

Ottobock

Ottobock 3C88/98-3

Ottobock 3C88/98-2

Ottobock 3C60 Kenevo®

Use the following steps for properly configuring the Ottobock microprocessorcontrolled knee with the 1T101 foot.

Genium and Genium X3

Special Considerations

- Follow the

X-Soft

Software Set-up

- In the Job

Bench

Static Alignment: F in the

C-Leg

Special Considerations:

C-Soft Plus

Bench Alignment: F (see

Static Alignment: F (see

Alignment: Follow the

software.

- In the Job Note: When using the Tube Adapter

Note: There is no selection of the foot type in C-Soft.

below).

Microprocessor Knees

been approved

possible combination

3B5 Genium® X3 3B1

Genium

software

Specification Note: When using the Tube Adapter foot selected, into

the configuration tool.

Note: Do not follow the bench alignment

will be

Software Set-up

selected, configuration tool.

incorrect

ollow the standard procedure for using the CAA

Specification

ollow the

ollow the C-Leg

® C-Leg® 4 C-Leg® 3

prompts for a fitting with a standard

the system height for that

Ottobock

Follow the

the system height for that

Ottobock

(restricted

tab,

choose

C-Leg

for the T

tab,

aiL

software prompts

choose

C-Leg

Static Alignment

the “Standard” option under Foot Type.

Bench

or Made

the “Standard” option under Foot Type

Bench Alignment

by Otto Bock

to sizes 22 cm – 27

Configuration

particular

Alignment

foot.

for a fitting with a

Configuration particular

recommendation in

with the

cm)

Ottobock

foot must be manually

recommendations

recommendation in

Tool in X Soft with

foot must be manually

recommendation in

foot.

Tool in X Soft with

(Computer Assisted

standard Ottobock foot.

the

‘Standard’

(see

below)

X-Soft since this

‘Standard’ foot

entered

the

instructions

entered

Alignment)

into

the

for use

Page 2

HealthCare

LP · 14255

6/17

Kenevo

Although this knee K2 knee with a c

Please contact

C-Leg

• Position the middle of the foot (MF)

• Noting the

•

and set the

• Mark the lateral

• Now position the

• The

•

C-Leg

• To

• Optimize the

Ottobock Ottobock Canada

US · P 800 328 4058 · F 800 655 4963 ·

allowed for use with the T

arbon

foot except under

special circumstances.

Ottobock Professional

Bench Alignment Recommendation

reference line (A). This the

product, regardless

of those

feet.

applies

of the

to all foot previous alignment specifications

alignment recommendation heel height rotation of the

Place

the

alignment reference outward rotation of the knee The recommended mm/0.79

Connect the foot and knee joint using a tube adapter. To do

dot. Mark a line 4H105

proximal centre (e.g.

adjustment software

Connect

(shoe

the

alignment reference

heel height – sole

foot.

line. Take into

sagittal

inch above the medial tibial

knee

required

extender

tube

center

through

(see IFU p

socket

of the

both dots from the

such that the

dot. Adjust the

hip joint contractures)

helps to

the

socket

and modular knee joint using an

point (=knee axis)

(the

adapter

positioning

length.

socket

age 22).

socket

and the ischial

determine

Static Alignment Recommendation

determine

plate

with the

the load line, have the patient (with

prosthesis

side and on the height prosthesis side must be sufficiently the

L.A.S.A.R. Posture.

alignment the distal and proximal set load

line (laser line) runs

(= knee

axis) of the knee

· P 800 665 3327 · F 800 463 3659 ·

solely by

screws

approx.

joint.

www

changing

.professionals.ottobockus.com

www.professionals.ottobock.ca

aiL

Clinical

from

approx.

components

of the foot

thickness

or Made

Service

foot,

clinician if wanting to use this

Instructions F

mm/1.18

inch anterior to the

that are

component,

in the forefoot area), and set the

approx.

account

the

knee-ground distance

insert provides

of the

alignment reference

plateau.

with a

centered,

socket

brim to the end of the

proximal dot and a

alignment reference

flexion to 3° – 5°, but take the individual situation

tuberosity-to ground distance

the

socket

flexion

adapter.

from the

Instructions

shoes) stand

compensation

loaded

35%

body weight). Note the weight display on

the plantar flexion. Only make

of the

socket adapter

mm/1.18

inch in front of the

Ottobock

would not typically suggest

or Use

alignment

recommended

in the

for use with

Instructions

add 5 mm to the effective

outward

0-5

mm/0-0.19

inch anterior to

and

for a rotation of

approx. 5°).

point is 20

so, tilt the joint in the correct

centered,

line

passes through

socket.

into

Use the

the

account.

precisely.

For

Use

on the force

measurement

plate with the other leg. The

adjustments

on the

prosthetic

foot, so that the

alignment reference

combination.

for Use

position

distal

point

this