Page 1
English Recharge LED Desk Lamp
CONGRATUL ATI ONS !
You’ve purchased the finest in natural lighting technology with your new OttLite
WARNING: To prevent electric shock, make sure the lamp is not plugged in until all
steps are complete.
NOTE: THIS UNIT IS FULLY ASSEMBLED
1.
Remove lamp from packing, placing lamp body base (A) flat on a steady surface.
2.
D
E
C
J
Connect power adapter input (F) into connector ( G) in the rear-bottom of the lamp.
3. Plug the power adapter (H ) into a standard household 120V AC outlet. Note: Only
use with the supplied power adapter to avoid damage or fire.
4. Power switch ( B) is a “touch” switch that controls ON/OFF power and the LED
brightness settings of the lamp.
5.
To power LED settings, slightly touch the switch to achieve the following:
• Turn lamp “ON” to 1st brightness setting; touch the switch “once”;
• for 2nd brightness setting; touch the switch “two-times”;
• for 3rd brightness setting; touch the switch “three-times”;
• to turn lamp “OFF”; touch the switch “four-times”.
6. Charge product using included USB cable (K) or AC adaptor (H). It will take
approximately 3.5 to 4 hours to charge lamp. LED indicator (J) will change from
RED to GREEN when lamp is fully charged. NOTE: Lamp battery charge will last
approximately two hours.
7. To reposition the light, hold the lamp base (A) steady and grasp either flex-neck (C )
or shade (D) depending on needed adjustment.
8. Refer to diagram 1 and 2 for lamp maximum adjustment range. NO TE: DO NOT
FORCE the shade outside allowable adjustable range as excessive adjustment may
cause damage.
®
product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any inter ference received, including interference that may
cause undesired operation.
CAUTION: Any change or modification to product not expressly recognized by OttLite
Technologies voids OttLite’s responsibility for proper function of product.
CAN ICES-005 (B)/NMB-005 (B)
CAUTION!
THIS PRODUCT CONTaINS a bUILT-IN LITHIUm-ION (LI-ION) baTTERY.
THIS IS a NON-REPLaCEabLE baTTERY. IN THE EvENT OF FaULTY baTTERY, ENTIRE PRODUCT
SHaLL bE PROPERLY DISPOSED OF IN aCCORDaNCE WITH LOCaL REgULaTIONS FOR
DISPOSaL OF HazaRDOUS maTERIaLS.
Li-ion Battery
Model: TY-18650-2000mAh
Capacity: 2000mAh (3.7Wh) Output Voltage: 3.7V
NOTICE:
Never disassemble by yourself.
Use the authorized charger only.
Exposure of battery to open flames could cause explosion.
Do not expose the battery pack out of the temperature range 32°F to 113°F
(0°C~45°C)
MADE IN CHINA
SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
H
G
F
K
OR INJURY TO PERSONS
1. Turn lamp off and WAIT UNTIL LAMP HEAD (D) IS COOL before handling.
2. The LED panel (E ) might get hot after several hours of continuous use DO NOT place
your hands directly on LED light panel.
3. Never use with an extension cord unless the plug can be fully inserted into the
receptacles in the extension cord.
4. Do not alter the plug.
5. The lamp head included with this unit cannot be replaced by the consumer.
6. INDOOR USE ONLY.
NOTE: The impor tant safety instructions appearing in this instruction sheet are not meant
to cover all possible conditions and situations that may occur. It must be understood that
common sense, caution, and care must be used with any electrical product.
SPECIFICATIONS:
USB: 5V, 500mA / Input power: 5V/500mA
Battery: Lithium, 3.7V / 2000mAh (power for LED Lights )
AC Adapter: Input: 100-240V, 50/60 Hz, 0.6A / Output: 5.0V DC, 1A
ACCESSORIES:
• USB Cord
• A/ C Adaptor
CAUTION!
IF THE ExTERNaL FLExIbLE CabLE OR CORD OF THIS LUmINaIRE IS
DamagED, IT SHaLL bE ExCLUSIvELY REPLaCED bY THE maNUFaCTURER OR ITS SERvICE
B
agENT OR a SImILaR qUaLIFIED PERSON IN ORDER TO avOID a HazaRD. INDOOR USE ONLY.
CAUTION!
THE LIgHT SOURCE OF THIS LUmINaIRE IS NOT REPLaCEabLE; WHEN
THE LIgHT SOURCE REaCHES ITS END OF LIFE THE WHOLE LUmINaIRE SHaLL bE REPLaCED.
FCC PART 15
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
A
Diagram 1
Diagram 2
Recharge LED Desk Lamp
CS59G59 CS59G59-SHPR CS59089-SHPR U2CFS
INS180456 REV021819
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dif ferent from that of the receiver.
• Consult the dealer or an experienced radio/T V technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Loading...