Otter Outdoors Wild Ice Lodge User Manual
Otter Wild Ice Lodge
Installation and Set-Up Instructions
Otter Wild Ice Lodge
Fits Magnum Otter Wild Sled Only
Parts Identification and Check List
MODEL NUMBERS:
Complete Pkg Thermal Roof Ice Camo 2046
PARTS LIST
Item # Qty Part # Description
1 1 1040 Sled - Black (Sold Separately)
2 1 90373 Tent-Ice Camo Lodge-Thermal Roof
3 1 80172 Frame Bracket “A”
4 1 80171 Frame Bracket “B”
5 1 80517 Back Wind Support Bar - 49 1/2”
6 1 80518 Center Wind Support Bar - 34 5/8”
7 1 80519 Center Wind Support Bar - 44 3/4”
8 1 80512 Adjustable Front Wind Support Bar
9 2 80470 Main Frame Extension Bar - 31 1/2”
10 2 80471 Main Frame Extension Bar - 32 1/2”
11 4 80472 Main Frame Extension Bar - 30”
12 2 80474 Outer Main Frame Bar - 33”
13 6 80473 Outer Main Frame Bar - 29 9/16”
14 4 80475 Middle Main Frame Bar - 52”
15 8 80489 Sleeve
16 16 40714 Self Tapping Screw & Plastic Protector
12 40714 Self Tapping Screw
17 8 80487 Black Plug
18 8 80488 Black End Cap
19 4 40103 5/16 Washer
20 12 80013 1/4 Nylon Hex Lock Nut
2
1
3
6
7
4
5
8
Back &
Center
11
15
10
9
Front
Bottom
16
12
17
Page 1
Front
13
Back
Center
Bottom
18
19
All
14
20
Instructions - 70775
T ools Required:
7/16” Box End W rench 3/8 Bit
7/16” Socket and Ratchet 5/16 Bit
Drill/Driver
Phillips Bit
3/32 Drill Bit (optional)
Note: Install bench seat before
the fish house framework.
1. Position sled (Item 1) as shown
in Diagram 1, with curved front
to your left. Using front drilling
pattern (on back page) mark
two holes for the front frame
bracket with a sharp object.
Using rear drilling pattern (on
back page), repeat this step for
the rear frame bracket.
2. Drill the 4 marked holes using a
5/16 bit.
3. Drill the 3/8 in. hole in center of
lip approximately 16 inches from
bend in sled. The back wind
support bar (Item 5) is to be
propped here.
Diagram 1
16 in.
3/8 in.
Hole
1
Place front and rear drilling
patterns in these corners.
4. Bolt frame brackets (Item 3 and Item 4) to sled using holes predrilled in Step 2.
Use appropriate fasteners shown in Diagram 2.
Diagram 2
3
19
20
Item 19 - 5/16 Washer
Item 20 - 1/4 Nylon Hex Lock Nut
4
Page 2
5. Assemble Back and Center Main Frame Bars: Insert the outer main frame bar (Item 13) into the middle main
frame bar (Item 14). Fasten with self-tapping screw and plastic protector (Item 16). Slide the sleeve (Item 15)
over the main frame extension bar (Item 11). (Line up holes with button lock, press lock in as you slide
over the bar). Insert the black plug (Item 17) into the main frame extension bar (Item 11). Insert outer main
frame bar (Item 13) into sleeve (Item 15). Cover end of main frame extension bar (Item 11) with black end cap
(Item 18). Ref. Diagram 3.
Diagram 3
11
17
Button
lock
13
13
16
Note: Predrilling a
3/32” hole will make
installation of
1615
screws easier.
14
16
16
Note: Use a light oil
such as WD-40 to
lubricate the poles to help
11
them slide easier. Wipe
off any excess. Silicone
may be substituted but is
18
not as effective.
6. Attach Back and Center main frame assemblies (Assembled in Step 5) onto frame brackets (Item 3 and 4).
Secure with 1/4 nylon hex lock nut (Item 20). Ref. Diagram 4.
Diagram 4
3
Center Main Frame Assembly
Back Main Frame Assembly
20
3
4
Page 3
Loading...