OT Systems FTD110DB-SSR3SA, FTD110DB-SSR3LSA, FTD110DB-SSR3, FTD110DB-SMR3SA, FTD110DB-SSR3L Installation And Operation Manual

FTD110DB-XXR3 Series Installation & Operation Manual

Installation and Operation Manual

FTD110DB-XXR3 Series

8-bit Digital Series

Triple Independent Video with Triple Bi-directional Data
Fiber Optic Receiver

www.ot-systems.com 1

OT Systems Ltd., 2014

Rev 1.2

FTD110DB-XXR3 Series Installation & Operation Manual

Standalone Units

Single-Mode Receivers
FTD110DB-SSR3SA
FTD110DB-SSR3LSA

Multi-Mode Receiver
FTD110DB –SMR3SA

Card Modules

Single-Mode Receivers
FTD110DB-SSR3
FTD110DB-SSR3L

Multi-Mode Receiver
FTD110DB-SMR3

FTD110DBMicro Series

FTD110DBM Series

FTD110DB Series

Single-Mode

FTD110DBMicro-SST
FTD110DBMicro-SSTL

Multi-Mode

FTD110DBMicro-SMT

Single-Mode

FTD110DBM-SST
FTD110DBM-SSTL

Multi-Mode

FTD110DBM-SMT

Single-Mode

FTD110DB-SST(SA)
FTD110DB-SSTL(SA)

Multi-Mode

FTD110DB-SMT(SA)

Models covered in this manual

Compatible with the following TRANSMITTERS:

Remark:

If the optical connector is FC type, the suffix in the model number will be “-FXX”. Eg.
FTD110DB-FSR3

www.ot-systems.com 2

FTD110DB-XXR3 Series Installation & Operation Manual

Table of Contents

(1) SAFETY INSTRUCTIONS .................................................................................................................................. 4

(2) PRODUCT OVERVIEW .................................................................................................................................... 5

2.1 INTRODUCTION ..................................................................................................................................................... 5

2.2 MODELS SELECTION TABLE ...................................................................................................................................... 6

(3) INSTALLATION................................................................................................................................................ 7

3.1 GENERAL ............................................................................................................................................................. 7

3.2 STANDALONE UNIT INSTALLATION .............................................................................................................................. 7

3.3 CARD MODULE INSTALLATION................................................................................................................................... 8

(4) CABLE CONNECTIONS & SETUP PROCEDURES ................................................................................................ 8

4.1 SYSTEM CABLE CONNECTIONS .................................................................................................................................. 8

4.2 DATA PORT ASSIGNMENT AND PIN CONNECTIONS ....................................................................................................... 10

4.3 DIP SWITCH SETTING PROCEDURES .......................................................................................................................... 11

4.4 GROUND CONNECTION ......................................................................................................................................... 13

(5) OPERATIONAL GUIDES ................................................................................................................................. 13

(6) SPECIFICATIONS ........................................................................................................................................... 14

(7) DRAWINGS .................................................................................................................................................. 15

(8) WARRANTY INFORMATION ......................................................................................................................... 15

(9) CONTACT INFORMATION ............................................................................................................................. 16

www.ot-systems.com 3

FTD110DB-XXR3 Series Installation & Operation Manual

(1) Safety Instructions

Please be familiar with all information in this manual prior to installation and
operation.

Note 1: The products described contain a Class 1 laser or LED fiber optic emitter. The following

safety precautions apply.

Warning: Do not disconnect the fiber optic connector while the unit is powered up.
Exposure to Class I invisible optical radiation is possible when the internal fiber optic
connector is disconnected while the unit is powered up.

Caution: Any access to the controls, adjustments, or performing operations, which are
other than those specified may result in hazardous radiation exposure. Permanent eye
damage or other bodily injuries may be resulted from such exposure even for only
seconds.

Note 2: This assembly contains parts sensitive to damage by electrostatic discharge (ESD). ESD
precautionary procedures should be applied in the course of touching, removing or inserting parts
or assemblies.

www.ot-systems.com 4

FTD110DB-XXR3 Series Installation & Operation Manual

(2) Product Overview

2.1 Introduction

The FTD110DB-XXR3 Series products comprise of either single-mode or multi-mode fiber
optic receivers catering for multi-channel optical transmissions of ONE forward (Tx → Rx) video
and ONE bi-directional (Tx ↔ Rx) data signal on THREE individual fiber links. The products work
at wavelengths of 1310nm and 1550nm with either a 9/125um or 62.5/125um fiber for
single-mode or multi-mode transmission respectively.

The FTD110DB-XXR3 Series products are compatible with the transmitters of the
FTD110DBMicro Series, FTD110DBM Series and FTD110DB Series.

A non-compressed 8-bit digital video transmission scheme is implemented which supports
video in NTSC, PAL and SECAM formats. Transparent data transmission is also accomplished in
RS232, RS422 and RS485 formats regardless of the type of communication protocol
implemented within the system. Time Division Multiplex (TDM) technology is employed for digital
transmission of forward video and data; whereas optical Wavelength Division Multiplex (WDM)
technology is employed for simultaneous reverse data transmission as well as bi-directional data
transmission.

For single-mode transmission, we also offer specifically designed products for long-haul
transmissions up to 60km. These models include the letter “L” in the suffix, e.g.
FTD110DB-SSR3L, etc.

The FTD110DB-XXR3 Series are available as standalone units, which can be mounted
horizontally or vertically wall-mounted on any fixture. The standalone unit comes with an external
power supply FT-PA/12V, which can be powered by local 110/220V power.

The FTD110DB-XXR3 Series are also available as plug-in card modules installed in a 19”
rack-mount chassis. Each plug-in card occupies two slot in the rack-mount chassis. The rack
mount chassis has to be ordered separately, and comes with its own power supply for powering
the installed card modules.

www.ot-systems.com 5