OT Systems FT410DBE-SSTSA, FT410DBE-SSRLSA, FT410DBE-SMTSA, FT410DBE-SMRSA, FT410DBE-SST Installation And Operation Manual

All Digital Fiber Optic Manufacturing Specialists

Installation and Operation Manual

FT410DBE Series

10-bit Digital Series

4-ch Video with 1 Bi-directional Data & Ethernet
Fiber Optic Converter

OT Systems Ltd., 2009

Rev 1.1

Models covered in this manual

Standalone Units

Single-Mode Transmitters

FT410DBE-SSTSA

FT410DBE-SSTLSA

Single-Mode Receivers

FT410DBE-SSRSA

FT410DBE-SSRLSA

Multi-Mode Transmitter

FT410DBE-SMTSA

Multi-Mode Receiver

FT410DBE-SMRSA

FT410DBE Series Installation & Operation Manual

Card Modules

Single-Mode Transmitters

FT410DBE-SST

FT410DBE-SSTL

Single-Mode Receivers

FT410DBE-SSR

FT410DBE-SSRL

Multi-Mode Transmitter

FT410DBE-SMT

Multi-Mode Receiver

FT410DBE-SMR

Remark:

If the optical connector is FC type, the suffix in the model number will be “-FXX”. Eg.

FT410DBE-FST

www.ot-systems.com 1

FT410DBE Series Installation & Operation Manual

Table of Contents

(1) SAFETY INSTRUCTIONS ...................................................................................... 3

(2) PRODUCT OVERVIEW .......................................................................................... 4

2.1 Introduction ....................................................................................................... 4

2.2 Models selection table ...................................................................................... 5

(3) INSTALLATION ....................................................................................................... 6

3.1 General ............................................................................................................. 6

3.2 Standalone unit installation ............................................................................... 6

3.3 Card module installation ................................................................................... 7

(4) CABLE CONNECTIONS & SETUP PROCEDURES .............................................. 7

4.1 System cable connections ................................................................................ 7

4.2 Data port assignment and pin connections ....................................................... 9

4.3 Dip switch setting procedures ......................................................................... 10

4.4 RJ-45 Pin Assignment for Ethernet Port ......................................................... 12

4.5 Ground connection ......................................................................................... 12

(5) OPERATIONAL GUIDES ...................................................................................... 12

5.1 FT410DBE Series Transmitter ....................................................................... 12

5.2 FT410DBE Series Receiver ........................................................................... 13

(6) SPECIFICATIONS ................................................................................................ 13

(7) DRAWINGS .......................................................................................................... 15

(8) WARRANTY INFORMATION ................................................................................ 15

(9) CONTACT INFORMATION ................................................................................... 15

www.ot-systems.com 2

FT410DBE Series Installation & Operation Manual

(1) Safety Instructions

Please be familiar with all information in this manual prior to installation and

operation.

Note 1: The products described contain a Class 1 laser or LED fiber optic emitter. The following

safety precautions apply.

Warning: Do not disconnect the fiber optic connector while the unit is powered up.

Exposure to Class I invisible optical radiation is possible when the internal fiber optic

connector is disconnected while the unit is powered up.

Caution: Any access to the controls, adjustments, or performing operations, which are

other than those specified may result in hazardous radiation exposure. Permanent eye

damage or other bodily injuries may be resulted from such exposure even for only

seconds.

Note 2: This assembly contains parts sensitive to damage by electrostatic discharge (ESD). ESD

precautionary procedures should be applied in the course of touching, removing or inserting parts

or assemblies.

www.ot-systems.com 3

FT410DBE Series Installation & Operation Manual

(2) Product Overview

2.1 Introduction

The FT410DBE Series products comprise of either single-mode or multi-mode fiber optic

transmitters and receivers for the optical transmission of FOUR forward (Tx → Rx) video, ONE

bi-directional (Tx ↔ Rx) data and ONE Ethernet signals on one fiber. The products work at

wavelengths of 1310nm and 1550nm with either a 9/125um or 62.5/125um fiber for single-mode

or multi-mode transmission respectively.

A non-compressed 10-bit digital video transmission scheme is implemented which supports

video in NTSC, PAL and SECAM formats. Transparent data transmission is also accomplished in

RS232, RS422 and RS485 formats regardless of the type of communication protocol

implemented within the system. Time Division Multiplex (TDM) technology is employed for digital

transmission of forward video and data; whereas optical Wavelength Division Multiplex (WDM)

technology is employed for simultaneous reverse data transmission as well as bi-directional data

transmission.

For single-mode transmission, we also offer specifically designed products for long-haul

transmissions up to 60km. These models include the letter “L” in the suffix, e.g. FT410DBE-SSTL

for Tx, FT410DBE-SSRL for Rx, etc.

The FT410DBE Series units are available as standalone units, which can be mounted

horizontally or vertically wall-mounted on any fixture. The standalone unit comes with an external

power supply FT-PA/12V, which can be powered by local 110/220V power.

The FT410DBE Series units are also available as plug-in card modules installed in a 19”

rack-mount chassis. Each plug-in card occupies two slots in the rack-mount chassis. The rack

mount chassis has to be ordered separately, and comes with its own power supply for powering

the installed card modules.

www.ot-systems.com 4