OT Systems FT110DB-SSRLSA, FT110DB-SSTSA, FT110DB-SMTSA, FT110DB-SMRSA, FT110DB-SST Installation And Operation Manual

All Digital Fiber Optic Manufacturing Specialists

Installation and Operation Manual

FT110DB Series

10-bit Digital Series

1-ch Video with 1 Bi-directional Data
Fiber Optic Converter

OT Systems Ltd., 2009

Rev 1.1

FT110DB Series Installation & Operation Manual

www.ot-systems.com 1

Models covered in this manual

Standalone Units

Single-Mode Transmitters

FT110DB-SSTSA

FT110DB-SSTLSA

Single-Mode Receivers

FT110DB-SSRSA

FT110DB-SSRLSA

Multi-Mode Transmitter

FT110DB-SMTSA

Multi-Mode Receiver

FT110DB-SMRSA

Card Modules

Single-Mode Transmitters

FT110DB-SST

FT110DB-SSTL

Single-Mode Receivers

FT110DB-SSR

FT110DB-SSRL

Multi-Mode Transmitter

FT110DB-SMT

Multi-Mode Receiver

FT110DB-SMR

Remark:

If the optical connector is FC type, the suffix in the model number will be “-FXX”. Eg.

FT110DB-FST

FT110DB Series Installation & Operation Manual

www.ot-systems.com 2

Table of Contents

(1) SAFETY INSTRUCTIONS....................................................................................... 3

(2) PRODUCT OVERVIEW .......................................................................................... 4

2.1 Introduction ....................................................................................................... 4

2.2 Models selection table ...................................................................................... 5

(3) INSTALLATION ....................................................................................................... 6

3.1 General ............................................................................................................. 6

3.2 Standalone unit installation ............................................................................... 6

3.3 Card module installation ................................................................................... 7

(4) CABLE CONNECTIONS & SETUP PROCEDURES ............................................... 7

4.1 System cable connections ................................................................................ 7

4.2 Data port assignment and pin connections ....................................................... 9

4.3 Dip switch setting procedures ......................................................................... 10

4.4 Ground connection ......................................................................................... 12

(5) OPERATIONAL GUIDES ...................................................................................... 13

5.1 FT110DB Series Transmitter .......................................................................... 13

5.2 FT110DB Series Receiver .............................................................................. 13

(6) SPECIFICATIONS ................................................................................................. 14

(7) DRAWINGS ........................................................................................................... 15

(8) WARRANTY INFORMATION ................................................................................ 15

(9) CONTACT INFORMATION ................................................................................... 15

FT110DB Series Installation & Operation Manual

www.ot-systems.com 3

(1) Safety Instructions

Please be familiar with all information in this manual prior to installation and

operation.

Note 1: The products described each contains a Class 1 laser or LED fiber optic emitter. The

following safety precautions apply.

Warning: Do not disconnect the fiber optic connector while the unit is powered up.

Exposure to Class I invisible optical radiation is possible when the internal fiber optic

connector is disconnected while the unit is powered up.

Caution: Any access to the controls, adjustments, or performing operations, which are

other than those facilitated and/or specified may result in hazardous radiation exposure.

Permanent eye damage or other bodily injuries may be resulted from such exposure even

for only seconds.

Note 2: This assembly contains parts sensitive to damage by electrostatic discharge (ESD). ESD

precautionary procedures should be applied in the course of touching, removing or inserting parts

or assemblies.

FT110DB Series Installation & Operation Manual

www.ot-systems.com 4

(2) Product Overview

2.1 Introduction

The FT110DB Series products comprise of either single-mode or multi-mode fiber optic

transmitters and receivers catering for optical transmission of ONE forward (Tx → Rx) video and

ONE bi-directional (Tx ↔ Rx) data signal in one fiber. The products work at wavelengths 1310nm

and 1550nm with either a 9/125um or 62.5/125um fiber for single-mode or multi-mode

transmission respectively.

A non-compressed 10-bit digital video transmission scheme is implemented which supports

multi-systems video in NTSC, PAL and SECAM formats. Transparent data transmission is also

accomplished in RS232, RS422 and RS485 formats regardless of the types of communication

protocol implemented within the system. Time Division Multiplex (TDM) technique is employed for

digital transmission of forward video and data; whereas optical Wavelength Division Multiplex

(WDM) technique is employed for simultaneous reverse data transmission so as bi-directional

data transmission is accomplished.

For the single-mode transmission, we also offer specifically designed products for long-haul

transmissions up to 60km. Their model names include a letter “L” in the suffix, e.g.

FT110DB-SSTL for Tx, FT110DB-SSRL for Rx, etc.

The FT110DB Series units are available as standalone units, which can be mounted

horizontally or vertically wall-mounted on any fixtures. The standalone unit comes with an

external power adaptor FT-PA/12V, which can be powered by a local residential power supply

outlet.

The FT110DB Series units are also available as plug-in cards installed in 19” rack-mount

chassis deployed in small, medium to large systems. Each plug-in card occupies one slot space

inside the rack-mount chassis. The rack mount chassis has to be ordered separately which is

integrated with a power supply unit for powering the installed card modules.