OT Systems ET2212-A-SA, ET2212-B-SA, ET2212-G-SA, ET2212-H-SA, ET2212-A-CM Installation And Operation Manual

ET2212 Series Installation & Operation Manual

All Digital Fiber Optic Manufacturing Specialists

Installation and Operation Manual

ET2212 Series

Network Switches Series

Industrial 2-port 10/100/1000BASE-TX to 1000BASE-LX Ethernet
Switch

OT Systems Ltd., 2011

Rev 1.0

Models covered in this manual

Standalone units

Fiber connector in SC

Multi-Mode (2-Fiber)

ET2212-A-SA

Single-Mode (2-Fiber)

ET2212-B-SA

Card Modules

Fiber connector in SC

Multi-Mode (2-Fiber)

ET2212-A-CM

Single-Mode (2-Fiber)

ET2212-B-CM

ET2212 Series Installation & Operation Manual

Fiber connector in ST

Multi-Mode (2-Fiber)

ET2212-G-SA

Single-Mode (2-Fiber)

ET2212-H-SA

Fiber connector in ST

Multi-Mode (2-Fiber)

ET2212-G-CM

Single-Mode (2-Fiber)

ET2212-H-CM

Table of Contents

ET2212 Series Installation & Operation Manual

TABLE OF CONTENTS ................................................................................................... 1

(1) SAFETY INSTRUCTIONS...................................................................................... 2

(2) PRODUCT OVERVIEW ......................................................................................... 3

2.1 Introduction ...................................................................................................... 3

2.2 Products Highlights .......................................................................................... 3

2.3 Models selection table ..................................................................................... 4

(3) INSTALLATION ...................................................................................................... 5

3.1 General ............................................................................................................ 5

3.2 Package Contents ........................................................................................... 5

3.3 Selecting a site for the Media Converter .......................................................... 5

3.4 Connecting to Power ....................................................................................... 6

3.5 Installation ........................................................................................................ 7

(4)

Cable Connections & Setup Procedures ................................................................. 9

4.1 System cable connections ............................................................................... 9

4.2 Connecting to Your Network .......................................................................... 10

(5) OPERATIONAL GUIDES ..................................................................................... 12

5.1 LEDs Status ................................................................................................... 12

5.2 Signal and Power Ports ................................................................................. 12

(6) SPECIFICATIONS ................................................................................................ 13

(7) DRAWINGS .......................................................................................................... 15

(8) WARRANTY INFORMATION ............................................................................... 15

(9) CONTACT INFORMATION .................................................................................. 16

APPENDIX A ..................................................................................................................... I

www.ot-systems.com 1

ET2212 Series Installation & Operation Manual

(1) Safety Instructions

Please be familiar with all information in this manual prior to installation and

operation.

Note 1: The products described contain a Class 1 laser or LED fiber optic emitter. The following

safety precautions apply.

Warning: Do not disconnect the fiber optic connector while the unit is powered up.

Exposure to Class I invisible optical radiation is possible when the internal fiber optic

connector is disconnected while the unit is powered up.

Caution: Any access to the controls, adjustments, or performing operations, which are

other than those specified, may result in hazardous radiation exposure. Permanent eye

damage or other bodily injuries may be resulted from such exposure even for only

seconds.

Note 2: This assembly contains parts sensitive to damage by electrostatic discharge (ESD). ESD

precautionary procedures should be applied in the course of touching, removing or inserting parts

or assemblies.

www.ot-systems.com 2

ET2212 Series Installation & Operation Manual

(2) Product Overview

2.1 Introduction

OT Systems' ET2212 media converter offers an easy and affordable solution for network

managers to connect 10/100/1000 Fast Ethernet from UTP to fiber optic cabling. The switch uses

a high performance auto-sensing exchange chip for full functionality of transfer and exchange,

guaranteeing the safety and stability of data transfer. The switches are Standalone Wall-mount

and can also operate in ET-C12 rack mount chassis, taking care of different installations. The

switches are available in both single-mode and multi-mode fiber.

2.2 Products Highlights

Basic Features

• Converts 10/100/1000Base-TX to 1000Base-LX

• 10/100/1000Mbps-Full/Half duplex, Auto-Negotiation

• Singlemode or Multimode fiber operation

• Dual-core fiber with SC or ST connectors

• Store and forward switching mechanism

• MDI/MDI-X Auto-Crossover supported

• Plug-and-Play/ Hot-swappable

• -20 °C to 60 °C (-4 °F to 140 °F) operating temperature

• Wall-mount or operate in ET-C12 rack mount chassis.

www.ot-systems.com 3

2.3 Models selection table

ET2212 Series Installation & Operation Manual

Descriptions

Models

Links

Max.

Installation

Fiber Options Wavelengths

Budget

ET2212-A-SA Multimode/2-fiber/SC 1310nm 19dB 500m

ET2212-B-SA Singlemode/2-fiber/SC 1310nm 19dB 20Km

ET2212-G-SA Multimode/2-fiber/ST 1310nm 19dB 500m

ET2212-H-SA Singlemode/2-fiber/ST 1310nm 19dB 20Km

Distance

requirements

Horizontally or

vertically

wall-mounted

Standalone unit

ET2212-A-CM Multimode/2-fiber/SC 1310nm 19dB 500m

ET2212-B-CM Singlemode/2-fiber/SC 1310nm 19dB 20Km

ET2212-G-CM Multimode/2-fiber/ST 1310nm 19dB 500m

Housed in ET-C12

chassis

2

ET2212-H-CM Singlemode/2-fiber/ST 1310nm 19dB 20Km

1

ET-PA/12V 1.25A 12VDC power adapter works under 100 -240VAC, 50/60Hz power supply; DC Jack(US, European, UK or

Australian power plug available)

2

Refer to ET-C12 for specifications.

1

www.ot-systems.com 4