OT Systems ET1111-B-MT, ET1111-E-MT, ET1111-C-MT, ET1111-D-MT, ET1111-F-MT Installation And Operation Manual

ET1111 Series Installation & Operation Manual

All Digital Fiber Optic Manufacturing Specialists

Installation and Operation Manual

ET1111 Series

Media Converter Series

Industrial 10/100BASE-TX to 100BASE-FX Ethernet Media
Converter

OT Systems Ltd., 2011

Rev 1.0

www.ot-systems.com

Models covered in this manual

Micro Type Wall-Mount

Fiber connector in SC

Multi-Mode (2-Fiber)

ET1111-A-MT

ET1111 Series Installation & Operation Manual

Fiber connector in ST

Multi-Mode (2-Fiber)

ET1111-G-MT

Single-Mode (2-Fiber)

ET1111-B-MT

Multi-Mode (1-Fiber)

ET1111-C-MT

ET1111-D-MT

Single-Mode (1-Fiber)

ET1111-E-MT

ET1111-F-MT

Single-Mode (2-Fiber)

ET1111-H-MT

Multi-Mode (1-Fiber)

ET1111-I-MT

ET1111-J-MT

Single-Mode (1-Fiber)

ET1111-K-MT

ET1111-L-MT

www.ot-systems.com

Table of Contents

ET1111 Series Installation & Operation Manual

TABLE OF CONTENTS ................................................................................................... 1

(1) SAFETY INSTRUCTIONS...................................................................................... 2

(2) PRODUCT OVERVIEW ......................................................................................... 3

2.1 Introduction ...................................................................................................... 3

2.2 Products Highlights .......................................................................................... 3

2.3 Models selection table ..................................................................................... 4

(3) INSTALLATION ...................................................................................................... 5

3.1 General ............................................................................................................ 5

3.2 Package Contents ........................................................................................... 5

3.3 Selecting a site for the Media Converter .......................................................... 6

3.4 Installation ........................................................................................................ 6

3.5 Installation- Wall Mount .................................................................................... 7

3.6 Connecting to Power ....................................................................................... 7

(4) CABLE CONNECTIONS & SETUP PROCEDURES .............................................. 8

4.1 System cable connections ............................................................................... 8

4.2 Connecting to Your Network ............................................................................ 9

(5) OPERATIONAL GUIDES ..................................................................................... 11

5.1 LEDs Status ................................................................................................... 11

5.2 Signal and Power Ports ................................................................................. 11

(6) SPECIFICATIONS ................................................................................................ 12

(7) DRAWINGS .......................................................................................................... 14

(8) WARRANTY INFORMATION ............................................................................... 14

(9) CONTACT INFORMATION .................................................................................. 15

APPENDIX A ..................................................................................................................... I

www.ot-systems.com 1

ET1111 Series Installation & Operation Manual

(1) Safety Instructions

Please be familiar with all information in this manual prior to installation and

operation.

Note 1: The products described contain a Class 1 laser or LED fiber optic emitter. The following

safety precautions apply.

Warning: Do not disconnect the fiber optic connector while the unit is powered up.

Exposure to Class I invisible optical radiation is possible when the internal fiber optic

connector is disconnected while the unit is powered up.

Caution: Any access to the controls, adjustments, or performing operations, which are

other than those specified, may result in hazardous radiation exposure. Permanent eye

damage or other bodily injuries may be resulted from such exposure even for only

seconds.

Note 2: This assembly contains parts sensitive to damage by electrostatic discharge (ESD). ESD

precautionary procedures should be applied in the course of touching, removing or inserting parts

or assemblies.

www.ot-systems.com 2

ET1111 Series Installation & Operation Manual

(2) Product Overview

2.1 Introduction

OT Systems' ET1111 media converter offers an easy and affordable solution for network

managers to connect 10/100 Fast Ethernet from UTP to fiber optic cabling. The media converter

series uses a high performance auto-sensing exchange chip for full functionality of transfer and

exchange, guaranteeing the safety and stability of data transfer. The media converter is available

in both single-mode and multi-mode fiber.

This Sleek Microtype design media converter occupies limited space and it's ideal solution for

easy installation within most camera housings.

2.2 Products Highlights

Basic Features

• Microtype design - fits within most camera housings

• Converts 10/100Base-TX to 100Base-FX

• Full/Half duplex, Auto-Negotiation

• Singlemode or Multimode fiber operation

• Single or Dual-core fiber with SC or ST connectors

• Store and forward switching mechanism

• MDI/MDI-X Auto-Crossover supported

• Plug-and-Play

• 12VDC or 24VAC Terminal Block Power inputs

• -10 °C to 60 °C (14 °F to 140 °F) operating temperature

• Supports Wall Mounting installation.

www.ot-systems.com 3

2.3 Models selection table

ET1111 Series Installation & Operation Manual

Descriptions

Models

Fiber Options Wavelengths

ET1111-A-MT Multimode/2-fiber/SC 1310nm 14dB 2Km

ET1111-B-MT Singlemode/2-fiber/SC 1310nm 21dB 20Km

ET1111-C-MT Multimode/WDM 1-fiber/SC TX:1310nm/RX1550nm 21dB 2Km

ET1111-D-MT Multimode/WDM 1-fiber/SC TX:1550nm/RX1310nm 21dB 2Km

ET1111-E-MT Singlemode/WDM 1-fiber/SC TX:1310nm/RX1550nm 19dB 20Km

ET1111-F-MT Singlemode/WDM 1-fiber/SC TX:1550nm/RX1310nm 19dB 20Km

ET1111-G-MT Multimode/2-fiber/ST 1310nm 14dB 2Km

ET1111-H-MT Singlemode/2-fiber/ST 1310nm 21dB 20Km

ET1111-I-MT Multimode/WDM 1-fiber/ST TX:1310nm/RX1550nm 21dB 2Km

ET1111-J-MT Multimode/WDM 1-fiber/ST TX:1550nm/RX1310nm 21dB 2Km

ET1111-K-MT Singlemode/WDM 1-fiber/ST TX:1310nm/RX1550nm 19dB 20Km

ET1111-L-MT Singlemode/WDM 1-fiber/ST TX:1550nm/RX1310nm 19dB 20Km

Links

Budget

Max.

Distance

Mounting

Micro Type

Wall-mount

www.ot-systems.com 4

ET1111 Series Installation & Operation Manual

(3) Installation

3.1 General

All OT Systems products are thoroughly inspected, tested and securely packaged before

delivery to ensure a stable, intact and trouble-free service. Please check the equipment upon

receipt for any visible damage which may have been caused during shipping.

3.2 Package Contents

When you unpack the product package, you shall find the items listed below. Please inspect

the contents, and report any apparent damage or missing items immediately to your authorized

reseller.

 Media Converter
 Quick Installation Guide
 External 12VDC power adapter & Power Cord

The ET1111 Series (Fig. 3.1) can be either horizontally or vertically wall-mounted, or fits

within the most camera housings, etc. It works with an external 12VDC or 24VAC power supply.

Fig. 3.1 ET1111

www.ot-systems.com 5

ET1111 Series Installation & Operation Manual

3.3 Selecting a site for the Media Converter

As with any electric device, you should place the Media Converter where it will not be
subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically,
the site you select should meet the following requirements:

- The ambient temperature should be between -10 to +60 degrees Celsius.

- The relative humidity should be less than 95 percent, non-condensing.

- Surrounding electrical devices should not exceed the electromagnetic field (RFC)
standards.

- Make sure that the Media Converter receives adequate ventilation.

- The power outlet should be within 1.8 meters of the Media Converter.

3.4 Installation

This chapter gives step-by-step instructions about how to install the Media Converter:

a) Mount the ET1111 onto a fixture or camera housings, e.g. a plank, (either on the

wall or on a flat surface) with two screws through the holes on the mounting

frame to secure it in position.

b) The power supply should also be mounted on the same fixture or in the proximity

for connection of the supply cables to the unit, provided that an AC power supply

socket is nearby for powering the adaptor.

c) Connect all the signal inputs and outputs at the unit with appropriate cables: fiber

optic cable for optical link and UTP/STP Cat 5 cable for Ethernet. Please refer to

Section 4.1 for the details.

d) Once the unit is powered up, check that the POWER LED on the unit is lit. If not,

check the power supply cable connections between the unit and the power

supply socket.

e) With all the signals available at the physical ports, check the status of LEDs

located on the unit. With correct status of each LED, installation is now completed

[for LEDs status, see Operational Guides on this manual’s Section (5)].

www.ot-systems.com 6

ET1111 Series Installation & Operation Manual

Ethernet Port

NETWORK

-

RJ45

connector

1 GND

Terminal

2 12V

3.5 Installation- Wall Mount

(a) Top view (b) Side view

Fig. 3.2 Dimension of Micro type units

• Installation: Mount the Micro type unit onto a fixture, or camera housings, e.g. a

plank, (either on the wall or on a flat surface) with at least 2 screws piercing through
the holes on the mounting frame to secure it in position.

• Startup: Connect the supply voltage to start up the Media Converter via the terminal

block.

• Removal: Locate and remove the securing screws. Usually, but not limited to, at

least 2 screws.

3.6 Connecting to Power

Bottom panel – Ethernet Port and Power Input

Power Input Assignment

Top Panel Bottom Panel

12VDC

Block

DC Terminal Block Power Input

Step 1: Connect the DC power cord to the pluggable terminal block on the bottom of

Media Converter and then plug it into a standard DC outlet.

Step 2: Disconnect the power cord if you want to shut down the Media Converter.

www.ot-systems.com 7

ET1111 Series Installation & Operation Manual

(4) Cable Connections & Setup Procedures

4.1 System cable connections

Signal

Type

Optical Single-mode or Multi-mode fiber SC or ST Connector Section 4.2.2

Ethernet Twisted-pair Cable

10BASE-T: UTP/STP Cat3, 4, 5

100BASE-TX: UTP/STP Cat 5

12VDC

Or

24VAC

Power cord

Cable Type Connector For details,

please refer to

RJ45 Connector Section 4.2.1

Terminal Block

Section 3.6

Wiring Diagram

12VDC

24VAC

12VDC
24VAC

Fig 4.1 Media converter connection diagram

www.ot-systems.com 8

ET1111 Series Installation & Operation Manual

4.2 Connecting to Your Network

4.2.1 Cable Type & Length

It is necessary to follow the cable specifications below when connecting the Media
Converter to your network. Use appropriate cables that meet your speed and cabling
requirements.

Cable Specifications

Speed Connector Port Speed

Half/Full Duplex

10Base-T RJ-45 10/20 Mbps 2-pair UTP/STP Cat. 3, 4, 5 100 m

100Base-TX RJ-45 100/200 Mbps 2-pair UTP/STP Cat. 5 100 m

100Base-FX SC, ST 100/200 Mbps MMF (62.5µm) 2 km

100Base-FX SC, ST 100/200 Mbps SMF (9 or 10µm) 20km

Cable

Max.

Distance

4.2.2 Cabling

Step 1: First, ensure the power of the Media Converter and end devices are turned off.

<Note> Always ensure that the power is off before any installation.

Step 2: Prepare cable with corresponding connectors for each type of port in use.

Step 3: Consult the cabling requirements based on connectors and speed.

Step 4: Connect one end of the cable to the Media Converter and the other end to a desired device.

Step 5: Once the connections between two end devices are made successfully, turn on the power and the

Media Converter is operational.

4.2.3 The 10/100Base-TX Connector/Cabling

A standard straight through cable is used for the connection between the Ethernet switch and

device. The products feature an auto-MDIX capability. For the details, Please see Appendix A for

your reference.

www.ot-systems.com 9

ET1111 Series Installation & Operation Manual

The 100Base

-

FX Connections

the RX

(receive) port of device I to the

TX (transmit) port of device II.

FIBER

ptical Connector

FIBER

ST Optical Connector

X

value:

FIBER

SC Optical Connector

X

value:

FIBER

ST Optical Connector

4.2.4 The 100Base-FX Connectors

The fiber port pinouts
The TX (transmit) port of device I is connected to the RX (receive) port of device II, and

X value:

A for Multimode fiber

B for Singlemode fiber

Connector

TX

SC O

RX

SC Optical Connector

X value:

G for Multimode fiber

H for Singlemode fiber

Connector

TX

RX

ST Optical Connector

The WDM 100Base-FX Connections

The fiber port pinouts

Only ONE optical fiber core is required to transmit and receive data.

* Special note for choosing WDM products:

Pair of products should be used for the optical transmission by different wavelengths (1310nm, 1550nm).

i.e. ET1111-C-MT should be match with ET1111-D-MT;
ET1111-E-MT should be match with ET1111-F-MT;
ET1111-I-MT should be match with ET1111-J-MT;
ET1111-K-MT should be match with ET1111-L-MT.

www.ot-systems.com 10

C and D for Multimode fiber
H and F for Singlemode fiber

Connector

I and J for Multimode fiber
K and L for Singlemode fiber

Connector

(5) Operational Guides

5.1 LEDs Status

LED State Indication

ET1111 Series Installation & Operation Manual

PWR

FX LINK

SPD

LINK/

ACT

Green Power on.

Off Power off.

Green 100Base-FX

Green 100Base-TX

Off 10Base-TX

Steady A valid network connection established

Flashing Transmitting or receiving data.

ACT Stands for Activity.

5.2 Signal and Power Ports

FIBER - SC or ST Optical Connector(s) for 100BASE-FX fiber cable connection.

NETWORK - RJ45 with Cat. 5 for 10/100BASE-TX Ethernet connection.

DC12V-

AC24V -

2-pin Screw Terminal Block for 12VDC or 24VAC power connection.

www.ot-systems.com 11

(6) Specifications

Ethernet

ET1111 Series Installation & Operation Manual

Standards

Address table size

Processing Type

Forward and Filter Rate

10Base-T

100Base-TX/FX

Cabling

10BASE-T

100BASE-TX

Maximum Distance

Cat5 UTP

Connector

10/100BASE-TX

IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX/FX

IEEE 802.3x

2048MAC addresses

Store-and-Forward

Half-duplex and IEEE802.3x Full-duplex flow control

10 / 20Mbps half / full-duplex

100 / 200Mbps half / full-duplex

UTP/STP Cat. 3, 4, 5 or above

UTP/STP Cat. 5 or above

Up to 100m

1X RJ45

Optical

Cabling

Maximum Distance

62.5/125µm (Multi-mode)

9/125µm (Single-mode)

Multi-mode fiber 2Km

Single-mode fiber 20Km

Wavelength(s)

1310nm

1310/1550nm

Connector

SC or ST

Electrical and Mechanical

Input Power

12VDC or 24VAC (Terminal Block)

Power Consumption

Operating Voltage & Max.

2.4W Max.

0.2A @ 12VDC

Current Consumption

www.ot-systems.com 12

LED Indicators

ET1111 Series Installation & Operation Manual

Power

10/100 TX (Per Port)

100FX (Per Port)

Dimensions

Net Weight

Casing

Mounting Options

Environmental

Operating Temperature

Storage Temperature

Humidity

Regulatory Approvals

ISO9001

FCC Part 15, Class A

Power Status

Link/Activity, Speed

Link/Activity

36.2mm (W) × 117mm (D) × 24.5mm (H)

0.12Kg (0.22kg including PA)

Aluminum case

Wall-Mount

-10°C to 60°C (14°F to 140°F)

-24°C to 85°C (-13°F to 185°F)

0% - 95% non-condensing

EN61000-3-2: 2006

EN61000-3-3: 2008

EN55024: 1998 +A1:2001+A2:2003

www.ot-systems.com 13

(7) Drawings

ET1111 Series Installation & Operation Manual

Fig. 7.1 Dimensional drawings of ET1111 (mm)

(8) Warranty Information

All ET-Series products are subject to a three-year warranty offered by the company in

normal circumstances. Please refer to the OT Systems Products Warranty Statement for details.

Access to the statement is available in our company website at www.ot-systems.com.

www.ot-systems.com 14

ET1111 Series Installation & Operation Manual

(9) Contact Information

APAC Operation EMEA Operation AMERICAS Operation

Address

Unit 1023, 10/F,

Landmark North

39 Lung Sum Avenue,

Sheung Shui, N.T.,

Hong Kong

Tel [phone]

Fax [phone]

Sales Inquiries

[e-mail]

Technical Support

[e-mail]

Address

J. Slovackio str. 4,

LT-11107, Vilnius

Lithuania

Tel [phone]

Fax [phone]

Sales Inquiries

[e-mail]

Technical Support

[e-mail]

Address

River Heights Business Park

5375 US Highway 34

Oswego, IL 60543

Tel [phone]

Fax [phone]

Sales Inquiries

[e-mail]

Technical Support

[e-mail]

www.ot-systems.com 15

RJ45

Appendix A

1. Connector Pinouts

2. TIA/EIA-568 Cabling

Pin #

1

2

3

4

5

6

7

8

Wire Diagram Wire Color

White/Green Transmit+

Green Transmit-

White/Orange Receive+

Blue Unused

White/Blue Unused

Orange Receive-

White/Brown Unused

Brown Unused Brown Unused

ET1111 Series Installation & Operation Manual

RJ45 Connector (Male)

T568A T568B

10Base-T Signal

100Base-TX Signal

Wire Diagram Wire Color

White/Orange Transmit+

Orange Transmit-

White/Green Receive+

Blue Unused

White/Blue Unused

Green Receive-

White/Brown Unused

10Base-T Signal

100Base-TX Signal

3. Standard, Straight-Through Wiring Diagram(both ends are the same):

The Straight-Through wiring (or called “regular” Ethernet cable), both ends should be use the

same pin out on of RJ45 port.

www.ot-systems.com I