Page 1
ET4222H-S-DR
Hardened IP CCTV Self-Configured 4-port 10/100/1000Base-T + 2-port 1000Base-X SFP Ethernet Switch
1 V1.0
This quick start guide describes how to install and use the Self-Configured Hardened Ethernet Switch. This is the
Switch of choice for harsh environments.
Overview
The ET4222H-S-DR product is a Self-Configured Hardened Ethernet switch which provides 4 port
10/100/1000Base-T + 2 port 1000Base-X SFP. SFP ports to support the use of SFP (Small Form-factor
Pluggable) transceiver module. User can chose different types of SFPs (1000M only). The Switch
supports 1 or 2 core Single-mode or Multi-mode fiber.
General
To ensure trouble free transportation and storage, all OT Systems products must be thoroughly inspected,
tested and well packed before delivery. Check the product upon receipt for any visible damage which may
have been caused during shipping.
Package Content
Hardened Self-Configured 4-port 10/100/1000Base-T + 2-port 1000Base-X SFP Ethernet Switch x 1
Quick Start Guide x 1
Physical Description
Front Panel
Rear Panel (Din-Rail)
Rear Panel (Wall mount)
Mounting holes
Page 2
ET4222H-S-DR
Hardened IP CCTV Self-Configured 4-port 10/100/1000Base-T + 2-port 1000Base-X SFP Ethernet Switch
2 V1.0
Left Side view
Installation
SFP Optical Module
You can select different SFP modules as required (Please refer to our SFP Ordering Options for the
appropriate module).
To insert/remove the SFP, the procedures are as follows:
1. On the front panel, insert the SFP module into the SFP port until it is securely locked.
2. Connect the optical fiber (1/2 core) to the LC connector(s) of the SFP.
3. To remove the SFP module, press down the lock of the LC connector of the optical fiber to pull out the
fiber cable.
4. Pull down the SFP lever and hold its position. Pull out the SFP module from the SFP port.
Page 3
ET4222H-S-DR
Hardened IP CCTV Self-Configured 4-port 10/100/1000Base-T + 2-port 1000Base-X SFP Ethernet Switch
3 V1.0
DIN Rail Installation
ET4222H-S-DR can be installed on a DIN rail. Installation steps are as follows:
Removal:
1. Pull down the metal part, pull out the lower part of the DIN rail clip until it leaves the track.
2. Lift up the upper part of the clip until the switch separate from the track.
Wall-Mount Installation
1. Put the switch close to the
DIN rail track. Lock the upper
part of the DIN rail clip on the
upper side of the track.
2. Press the switch until
the metal part move
downward and a “click”
sound is heard.
3. The metal part is then moved back
to its original position. The switch is
securely locked on the track. The
installation is completed.
Top
Hook
Locking
Slide
1. Remove the screws to
take out the DIN rail clip
from the switch.
2. Tighten the screws to fix the
wall mount plate and the switch
together.
3. Mount the switch on the wall
or on a flat surface with 2 screws
piercing through the mounting
holes to secure it in position.
Mounting
Holes
Page 4
ET4222H-S-DR
Hardened IP CCTV Self-Configured 4-port 10/100/1000Base-T + 2-port 1000Base-X SFP Ethernet Switch
4 V1.0
Setup
1. Connect one end of each Ethernet cables to its corresponding port on the ET4222H-S-DR. Connect
the other end to the network equipment (IP camera, Switch or PC). Insert the SFP and connect the
optical fiber cable to its corresponding connector.
2. Connect the ET4222H-S-DR to the power supply. Ensure the power supply in connected to a power
source and the PWR indicator is ON. If not, please ensure that the power cable is connected
properly and the power supply is functioning normally.
3. After all cables are connected, the indicators will be lit as per port status LEDs (page 5).
Interface
RJ-45 Pin Assignment
Pin
Signal Name
1
TP0+
2
TP0-
3
TP1+
4
TP2+
5
TP2-
6
TP1-
7
TP3+
8
TP3-
Power Connection：
Pin
Description
V1 - V1 + V2 - V2 +
Power Input
GND
+12~48V
(DC)
GND
+12~48V
(DC)
Add ALM with normal close/open?
Cable Connections
Signal Type Cable Type Connector
Ethernet
Cat. 5 or above RJ45
Optical
SM/MM Optical fiber cable (depends on SFP) LC
Power supply 1
Power cable
6-pin Terminal Block（Pin 1/2）
Power supply 2
Power cable
6-pin Terminal Block（Pin 5/6）
ALM
2 wire
6-pin Terminal Block（Pin 3/4）
Page 5
ET4222H-S-DR
Hardened IP CCTV Self-Configured 4-port 10/100/1000Base-T + 2-port 1000Base-X SFP Ethernet Switch
5 V1.0
LED Indicators
Indicator Color Status Description
PW1
Green
ON Powered on
PW2
Green
ON Powered on
ALM
Green ON Alarm contact close when either of the power supplies is off
SFP1,2
Green
ON Fiber link up
OFF Fiber is not connected or fiber link down
IGMP
Green
ON Enable IGMP Snooping
OFF Disable IGMP Snooping
RJ45 Port
(P1-P4)
LINK/ACT
Green
ON A network device is connected
Blinking The connected device is transmitting or receiving data.
OFF No network device is connected
Dip Switch
Ports
ALM
ON Enable Power Failure Alarm (Default setting)
OFF Disable Power Failure Alarm
IGMP
ON Enable IGMP Snooping (Default setting)
OFF Disable IGMP Snooping
P1-P4
Ethernet ports
SFP1, SFP2
Fiber port
Power Input
12~48VDC input (Double power input)
Page 6
ET4222H-S-DR
Hardened IP CCTV Self-Configured 4-port 10/100/1000Base-T + 2-port 1000Base-X SFP Ethernet Switch
6 V1.0
Dimensions Drawing of the Product (Unit: mm)
Functional Description
2048 MAC address
1M bits buffer memory
Supports 9K Bytes Jumbo Frame
Supports Energy Efficient Ethernet IEEE802.3az
Support 10/100/1000Mbps-Full/Half-duplex, Auto-negotiation, Auto-MDI/MDIX
Supports Light Hardware IGMP V1, V2, V3; DIP switch selectable
Support Relay output (Dry Contact, 1A@DC 24V) for power fail alarm; DIP switch selectable.
-40°C to 75°C ( -40°F to 167°F) operating temperature range
Supports Wall-mount and DIN-Rail installation
Manual Earth Green manual is available in our website. www.ot-systems.com
Loading...