MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Kensington - 3 Door Mirror Robe
Assembly Instructions - Please keep for future reference
411/7542
413/6949
Width - 125.6cm
Depth - 49.5cm
Height - 198.8cm
Issue 1 - 16/06/15
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 93kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Top (DF3757)
(125.6 x 49.5cm)
Base (DF3765)
(119.4 x 47.4cm)
Inner Top (DF3766)
(119.4 x 47.4cm)
Wide Shelf (DF3761)
(79.7 x 45cm)
1 2
3 4
Narrow Shelf (DF3764)
(38.2 x 45cm) x 4
5
Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
2
Front Plinth (DF3762)
(125.6 x 9.2cm)
Rail (DF3760)
(119.4 x 9.2cm) x 2
Side Plinth (DF2431)
(47.5 x 9.1cm) x 2
Plain Door (DF3767)
(184.5 x 39.4cm) x 2
Mirror Door (DF5210)
(184.5 x 39.4cm)
(Mirror - SG29
177.6 x 30cm
Safety Back SAR)
Small Back (X1892-401)
(189.2 x 40.1cm)
Large Back (X1892-816)
(189.2 x 81.6cm)
Left Side (DF3758)
(197.3 x 47.5cm)
6
Right Side (DF3759)
(197.3 x 47.5cm)
Divider (DF3763)
(185.1 x 45.1cm)
7 8
10
9
11
13 14 15 16
Hanging Rail (FHR791)
(79.1cm long)
12
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
3
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Tools required
Scissors / Rule / Hammer / Cross-head screwdriver / Square / Spirit level / Step ladder
Eye protection (when using a hammer or drill)
Electric drill (only use when drilling into walls)
A B
D E
G H
C
F
P Q
Large locking
nut (F900) x 24
Metal dowel (F901) x 24 Wooden dowel (F22) x 26
Hinge plate
(F523) x 12
Hinge (F522) x 12
I
40mm Screw (F910) x 2
19mm Screw (F461) x 2
Back holder (F276) x 6
* These can also be round
Nail screw (F277) x 6
L
Shelf stud (F110) x 16
N
Handle (F220) x 2
J K
Nail (F51) x 42
Plastic Nail (F91) x 6
13mm Screw (F63) x 28
25mm Screw (F50) x 4
M
Rail Holder
(F891) x 2
O
Strap
Screw Washer x 2
Overbalance protector kit (F269) x 1
Assembly Instructions
4
Step 1
C
C
Prepare the divider
a: Screw 2 metal
dowels into the
divider .
Note: Tighten the metal
dowels up fully against
the panels.
Insert 2 large locking
nuts into the
divider .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 4 wooden dowels
into the divider .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
b: To fit the rail holder
screw through the top
hole with screw and
into the mark hole drilled
in the divider . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
Fit 4 hinge plates onto
the divider , making
sure that the slot is
facing towards the
finished front edge.
A
8
8
C
8
A
G
M
G
M
10mm
C
B
B
M
G
8
G
P
8
b:
a:
B
B
A
A
C
C
Finished
front edge
8
1
G
G
M
Finished
front edge
P
P
P
P
P
8
Finished
front edge
Finished
front edge
C
C
C
C
Assembly Instructions
5
Step 2
Step 3
Prepare the inner top
Screw 2 metal dowels
into the inner top .
Insert 4 large locking
nuts into the inner top
. .
Tap 4 wooden dowels
into the inner top .
3
C
3
B
B
B
B
B
C
C
A
A
Finished
front edge
Important: The inner top is
very similar to the base but,
the inner top will only have
holes on one surface.
3
A
B
Fit the inner top to
the divider
Push the inner top
onto the divider .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the divider .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 4
3
8
B
B
8
3
8
B
B
B
B
C
C
Prepare the wide shelf
Insert 4 large locking
nuts into the wide
shelf .
Tap 4 wooden dowels
into the wide shelf .
4
C
4
B
Finished
front edge
A
3
4
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 5
8
4
Fit the wide shelf
Push the wide shelf
onto the divider .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the wide shelf .
4
8
B
4
C
C
B
B
B
B
C
C
Finished
front edge
2
Step 6
Prepare the base
Insert 4 large locking
nuts into the base .
Tap 4 wooden dowels
into the base .
Step 7
Fit the base
Push the base onto
the divider and
secure it using 2 screws
. .
2
C
2
B
D
D
2
8
D
2
8
C
C
Assembly Instructions
7
Step 8
Prepare the right side
a: Screw 6 metal
dowels into the right
side .
Insert 2 large locking
nuts into the right
side .
b: Tap 2 wooden
dowels into the right
side .
Fit 4 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
A
7
7
C
7
B
b:
a:
B
B
A
A
A
A
A
A
P
P
P
P
Finished
front edge
Finished
front edge
P
7
7
7
Fit the right side
Push the right side
onto the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the base and inner
top .
7
B
2
3
Step 9
7
2
3
Finished
front edge
Finished
front edge
C
Assembly Instructions
8
Step 10
C
C
B
B
P
P
P
P
A
A
A
A
A
A
A
G
G
M
A
Prepare the left side
a: Insert 2 large locking
nuts into the
left side .
Tap 2 wooden dowels
into the left side .
Fit 4 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
b: Screw 8 metal
dowels into the left
side .
To fit the rail holder
screw through the top
hole with screw and
into the mark hole drilled
in the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
A
6
6
C
6
B
M
G
6
G
P
6
b:
a:
6
6
P
B
B
C
Prepare the 2 rails
Insert 2 large locking
nuts into each of the 2
rails .
Tap 2 wooden dowels
into each of the 2 rails .
9
C
9
B
Step 11
9
x 2
Assembly Instructions
9
Step 12
Fit the right side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 8 large
locking nuts fitted to
the base , inner top ,
wide shelf and 2 rails
. .
Step 13
9
9
Fit the 2 rails
Push the 2 rails onto
the assembly.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the 2 rails .
9
B
9
Note: Support this rail
until the left side has been
fitted in the next step.
9
9
6
B
2 3
4
9
6
2
3
4
Polystyrene
block
Polystyrene
block
Assembly Instructions
10
Step 14
Prepare the top
Screw 4 metal dowels
into the top .
A
1
A
A
A
A
1
1
Step 15
Fit the top
Note: To make it easier
to fit the top and plinths,
place polystyrene blocks
from the packaging
underneath the side
panels to raise the
assembly.
Push the top onto
the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the sides and .
B
6 7
1
6
7
Polystyrene
block
Polystyrene
block
Warning: The
unit is heavy.
Lift with care.
yy
yy
xx
xx
Assembly Instructions
11
Step 16
Fit the 2 back panels
a: Square up the unit by
making sure that
measurement x:x equals
y:y.
Place the small back
and large back ,
coloured surface facing
down, onto the unit as
shown.
Make sure that the 2
backs are pushed up
tight against each other
and that they meet in the
centre of the divider’s
back edge.
b: Nail around the
outside edges of the 2
backs.
Note: Do not nail where
the 2 backs meet.
c: Push the nail screws
. through the back
holders and tap them
down between the small
back and large back
. and into the back
edge of the divider .
Keep tapping the nail
screws in until the
back holders dig into
the small and large back.
15
16
J
H
I
15
16
8
H
I
Note: If ever you need to take
the backs off to dismantle the
unit, the nail screws can be
taken out using a screwdriver.
H
I
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
Note: These can
also be round
IH
+
c:
H
I
15
16
I
b:
J
15
16
C
Assembly Instructions
12
Step 17
Fit the 6 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
Tap 2 plastic nails
into the bottom edge of
the front rail . .
K
6
7
K
K
K
K
7
6
K
K
K
9
9
Step 18
Prepare a side plinth
Insert a large locking
nut into 1 of the side
plinths .
Tap a wooden dowel
into the side plinth .
11
B
11
C
Step 19
Prepare the other side
plinth
Insert a large locking
nut into the side plinth
. .
Tap a wooden dowel
into the side plinth .
11
B
11
C
B
C
Finished
top edge
11
Finished
top edge
11
B
Finished
top edge
Profiled
top edge
Finished
top edge
Assembly Instructions
13
Step 20
Profiled
top edge
Prepare the front
plinth
Screw 2 metal dowels
into the front plinth .
Step 21
A
5
Fit the plinths together
Push the 2 side plinths
onto the front plinth .
Use a screwdriver to
tighten the large locking
nuts fitted to the side
plinths .
11
10
B
11
A
A
10
10
11
11
E
E
Step 22
Fit the plinths
Position the 3 plinths
around the outside of the
assembly, ensuring that
the bottom edge of the
plinths are flush with the
bottom edge of the
sides, as shown.
Secure the 2 side plinths
. through the left end
. . and right end
using screws .
11
6 7
E
11
E
E
11
6
7
11
Assembly Instructions
14
Step 23
L
x 4
L
x 4
L
x 4
L
x 4
Fit the narrow shelves
Carefully stand the
unit up.
For each of the 4 narrow
shelves , insert 4 shelf
studs .
Lower the 4 narrow
shelves down onto
the shelf studs .
L
5
5
L
5
5
5
5
Step 24
Warning: The
unit is heavy.
Lift with care.
Fit the hanging rail
Push the hanging rail
into the rail holders
fitted to the panels.
12
M
12
M
12
Assembly Instructions
15
Step 25
Prepare the 2 plain
doors
Push fit 4 hinges into
each of the 2 plain
doors .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
G
Q
13
90
Q
x 2
Q
G
G
Q
G
G
Q
G
G
Q
G
G
Q
G
G
Q
G
G
Q
G
G
Q
G
G
Prepare the mirror
door
Push fit 4 hinges into
the mirror door .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
G
Q
14
Step 26
13
14
Warning:
Glass! Handle
with care
Assembly Instructions
16
Step 27
Fit doors and handles
Note: The easiest way to
attach each door and
. is to fit the top hinge
first, then align and fit the
other hinges.
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
the 2 plain doors
using screws .
Important: DO NOT attempt to
attached a handle to the mirror door.
Q
Q
Q
P
P
P
Q
P
N
F
13
14
13
a: b:
c: d:
P
Q
P
P
B
P
Q
Q
Q
A
Q
P
B
e:
Warning:
Glass! Handle
with care
N
F
N
13
14
13
Assembly Instructions
Step 28
17
b:
c:
d:
a:
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
A
A
B
C
Assembly Instructions
Step 29
18
Fit the overbalance
protector
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by fitting of the
overbalance protector kit
. to the unit, or an
alternative fixing method
of your choice.
Wall fixings are not
supplied as they will
need to suit the wall
type.
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
O
O
WALL
Wall fixing
(not supplied)
Screw
(not supplied)
Washer
Strap
O
Strap
Washer
Screw
TOP OF UNIT
O
Assembly Instructions
19
ALR3174
Step 30
Assembly is complete
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
IMPORTANT INFORMATION ABOUT THIS PRODUCT
This product complies with the requirements of BS 7449:1991 and has been manufactured by
DECORATIVE PANELS FURNITURE LTD, TEESSIDE INDUSTRIAL ESTATE,
THORNABY-ON-TEES, CLEVELAND, TS17 9LT
.
The product code for this unit and the item code(s) for the glass components are listed in the Assembly
Instructions along with a description of the type of glass used. All clear/tinted glass complies with the
requirements of BS 6206 Class A. All mirrors comply with the requirements of BS 6206 Class C. If the
glass component contained in this unit is chipped or broken consult the furniture manufacturer, retailer,
or agent with regard to obtaining a manufacturing specification and shape for replacement glass
quoting the unit description and batch number or date of manufacture.
Do not place very hot or very cold items against or in close proximity to glass surface(s) unless
adequately thick insulating material is used to prevent such items coming in contact with the glass.
Do not strike the glass with hard or pointed items.
Do not sit or stand upon horizontal glass surfaces.
When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if
necessary - do not use washing powders or any other substance containing abrasives since these
substances scratch glass.
If stated in the instruction leaflet, it is essential that this unit is fixed to a wall.
KEEP THESE INSTRUCTIONS FOR FUTURE USE
Loading...