Oster 10 - 76010 User Manual
Heavy-Duty Detachable
Blade Clipper
Instruction Manual
• For Commercial Use Only •
Model 10 - 76010
IMPORTANT SAFEGUARDS
Commercial Clipper • When using an electrical appliance, basic precautions
should always be followed, including the following:
Read all instructions before using this appliance.
4. Never operate this appliance if it has
DANGER
To reduce the risk of electric shock:
1. Do not reach for an appliance that has
fallen into water. Unplug immediately.
2. Do not use while bathing or in a
shower.
3. Do not place or store appliance where
it can fall or be pulled into a tub or
sink.
4. Do not place in or drop into water
or other liquid.
5. Always unplug this appliance from
the electrical outlet immediately after
using.
6. Unplug this appliance before cleaning,
putting on or taking off parts.
WARNING
To reduce the risk of burns, fire,
electric shock, or injury to persons:
1. An appliance should never be left
unattended when it is plugged in.
2. Close supervision is necessary when
this appliance is used by, on, or near
children or invalids.
3. Use this appliance only for its intended
use as described in this manual. Do not
use attachments not recommended by
the manufacturer.
a damaged cord or plug, if it is not
working properly, if it has been dropped
or damaged, or dropped into water.
Return the appliance to a service center
for examination and repair.
5. Keep cord away from heated surfaces.
6. Never operate the appliance when air
openings are blocked or while on a soft
surface (such as a bed or couch).
7. Never drop or insert any object into
opening.
8. Do not use outdoors or operate where
aerosol spray products are being used
or where oxygen is being administered.
9. Do not use this appliance with a
damaged or broken comb or blade,
as cut or scratched skin may occur.
10. To disconnect, move all controls to
“OFF”, then remove plug from outlet.
11. Do not wrap cord around unit when
storing. Continuous stress on the
cord can damage cord insulation and
result in a shock hazard.
12. Avoid contact with moving blades.
13. Avoid tangling or kinking the cord
while clipping. Should the cord become
tangled or kinked, stop clipping and
straighten the cord.
SAVE THESE INSTRUCTIONS
THE FOLLOWING PARAGRAPH IS FOR 120-VOLT MARKETS ONLY
To reduce the risk of electrical shock, this appliance has a polarized plug
(one blade is wider than the other). This plug fits a polarized outlet only one
way. This is a safety feature intended to help reduce the risk of electrical
shock. If the plug does not fit fully into the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not attempt to defeat this
safety feature.
ABOUT YOUR CLIPPER
Although your clipper has been thoroughly tested and inspected at every
stage of its manufacturing and assembly, it is recommended that you lubricate it, as instructed in this manual, after 4-6 weeks of extensive use. This
will ensure you obtain optimum performance and prolong the life of your
clipper.
GETTING FAMILIAR WITH
YOUR CLIPPER
Due to continuous product improvement, product may vary slightly from
what is illustrated.
1. Blade guard
2. Blade
3. Blade bracket
4. Blade hinge
5. Name plate/gear drive assembly access
6. Carbon brush cap/carbon brush
7. Oiler
8. Power cord
9. On/Off switch
10. Hanging ring
11. Cleaning Brush
12. Oster® Clipper & Blade Lube™ oil
13. Oster Gear Lube® grease
1
2
3/4
5
4
7
6
6
6
8910
11
12
13
AVAILABLE OSTER® LUBRICANTS & CLEANERS,
& REPLACEMENT PARTS
Regular use of the following products will help you enjoy optimum performance from your
clipper and prolong its functionality.
Oster 5-in-1®
(076300-107)
All-purpose clipper
& blade lubricant
and disinfectant.
Blade Lube™
Oil 76300-104
Lubricates between
upper and lower
blades to keep
them sharper longer and produce a
smoother clipping
action
To order any of these products, please call 1-800-830-3678 or visit www.osterstyle.com
Kool Lube® 3
76300-101
Lubricates and
cools down blade.
Gear Lube®
(076300-105)
Specially designed
to prolong the life of
gears, bearings and
the motor.
Spray
Disinfectant
76300-102
Minimizes bacteria
buildup between
upper and lower
blades.
Blade Wash®
Cleaning
Solution 76300103
Flushes away
accumulated hair
and removes dirt
buildup trapped
between upper
and lower cutting
blades.
Replacement carbon brushes
(076917-710)
Set of replacement carbon brushes and
springs
USING YOUR CLIPPER
Important:
• Before using your clipper, apply 1 or 2 drops of Oster® Clipper & Blade
Lube™ Oil to the blade (refer to Taking Care of Your Clipper section).
• For best results, hair should be clean and free from styling agents.
• During use, apply Kool Lube® coolant occasionally to the blades to keep
them cool.
1. Plug unit into an AC electrical outlet.
2. Move On/Off switch to turn clipper on.
3. Remove blade guard.
4. Insert blade. Holding blade sides, slide blade bracket into hinge.
5. Push blade toward the clipper until it snaps into place
STEP 4
STEP 5
6. When finished clipping, turn clipper off and unplug cord from electrical outlet.
7. Cover blade with blade guard to keep it protected.
TAKING CARE OF YOUR CLIPPER
Note: Any other maintenance not explained in this manual must be performed by an Oster-Direct® Authorized Service Center.
Important: Make sure clipper is turned off and unplugged from electrical
outlet before removing, replacing or cleaning any parts.
Lubricating Motor
If you hear a “squeal” or a dry bearing noise
from the motor, it is a signal that the motor
needs lubricating.
Remove cap from Oster® Clipper and Blade
Lube™ tube and insert tip into oiler to apply 1
drop of oil. Be careful not to over lubricate.
Greasing Gear Drive Assembly
We recommend checking the gear drive
assembly every six months for greasing.
Caution: Grease only when necessary as over-greasing may cause
leakage and reduce clipper’s efficiency.
APPLY 1
DROP
10-76010_12EM1.indd 1 8/7/12 11:03 AM
1 YEAR LIMITED WARRANTY
Sunbeam Products, Inc, or if in Canada, Sunbeam Corporation (Canada) Limited
(collectively “Sunbeam”) warrants that for a period of one year from the date of
purchase, this Oster® Professional Product will be free from defects in material
and workmanship. Sunbeam, at its option, will repair or replace this product or
any component of the product found to be defective during the warranty period.
Replacement will be made with a new or remanufactured product or component.
If the product is no longer available, replacement may be made with a similar
product of equal or greater value. This is your exclusive warranty. This warranty is
valid for the original retail purchaser from the date of initial retail purchase and is
not transferable. Keep the original sales receipt. Proof of purchase is required to
obtain warranty performance. Sunbeam dealers, service centers, or retail stores
selling Sunbeam products do not have the right to alter, modify or any way
change the terms and conditions of this warranty. This warranty does not cover
normal wear of parts or damage resulting from any of the following: negligent use
or misuse of the product, use on improper voltage or current, use contrary to the
operating instructions, disassembly, repair or alteration by anyone other than
Sunbeam or an authorized Sunbeam service center. Further, the warranty does
not
cover: Acts of God, such as fire, flood, hurricanes and tornadoes.
What are the limits on Sunbeam's Liability?
Sunbeam shall not be liable for any incidental or consequential damages caused
by the breach of any express, implied or statutory warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or
condition of merchantability or fitness for a particular purpose is limited in
duration to the duration of the above warranty. Sunbeam disclaims all other
warranties, conditions or representations, express, implied, statutory or
otherwise. Sunbeam shall not be liable for any damages of any kind resulting
from the purchase, use or misuse of, or inability to use the product including
incidental, special, consequential or similar damages or loss of profits, or for any
breach of contract, fundamental or otherwise, or for any claim brought against
purchaser by any other party. Some provinces, states or jurisdictions do not allow
the exclusion or limitation of incidental or consequential damages or limitations
on how long an implied warranty lasts, so the above limitations or exclusion may
not apply to you.
This warranty gives you specific legal rights, and you may also have other rights
that vary from province to province,state to state or jurisdiction to jurisdiction.
In the U.S.A., this warranty is offered by Sunbeam Products, Inc located in Boca
Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation
(Canada) Limited, located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1.
PLEASE DO NOT RETURN THIS PRODUCT TO EITHER OF THESE ADDRESSES.
1. Using a small Phillips-head screwdriver,
unscrew name plate mounting screws.
2. Remove name plate to expose gear drive
assembly.
3. Remove cap from Oster® Gear Grease tube
and apply a generous amount of grease to
eccentric, gears and bearing, as illustrated.
4. Once finished greasing, replace name plate
and tighten screws.
Removing and Replacing Worn Out Carbon Brushes
Your clipper contains a carbon brush that will wear out with normal use.
When this begins to occur, the clipper will operate intermittently. If the clipper
does not turn on, this is a sign that the carbon brush is worn out and needs
to be replaced.
Important:
• Youwillneedtoreplaceboth carbonbrushesatthesametime,
even if only one brush is worn out.
• Useonly Oster® carbon brushes. Carbon brushes used in electric
motors are carefully selected for size and grain to ensure optimum
performance. Using other brushes will compromise your clipper’s
performance.
1. Nylon cap
2. Brass cap
3. Spring
4. Brush tube
5. Carbon brush
5
To remove and replace carbon brush, follow below instructions:
1. Unscrew and remove brush cap.
Tip: A dime is an ideal tool for loosening the cap.
2. Pull out nylon cap and brass cap with your fingers by using a “picking”
action.
3. Remove spring and carbon brush.
4. Inspect length of carbon brush. Replace
if length is reduced to 5 mm or less.
5. To insert new carbon brush, hold the
brush and turn it until it falls into place.
6. If spring became loose, insert it into
brush tube.
7. Place brass cap over the spring, pressing down to seat brass cap into the
brush tube.
8. Insert nylon cap over brass cap.
9. Replace brush cap and turn clockwise to screw securely into place.
ECCENTRIC, GEAR
AND BEARING
KEEP
REPLACE
1234
Blade Care and Cleaning
Lubricating
Blades should be oiled regularly to reduce heat and maintain sharpness.
Before removing the blade, be sure it has cooled down.
1. With clipper in off position, push blade
away from clipper with your thumb.
2. Place 1 or 2 drops of Oster® Clipper and
Blade Lube™ oil on the blade. Wipe
excess oil with a dry, soft cloth.
3. Turn on clipper and push blade toward
clipper until it snaps securely into place.
OIL
Cleaning
1. Clean the excess hair from your blades
by using the cleaning brush.
2. To clean the blades, plug clipper into electrical outlet and turn on.
3. In a shallow pan, immerse blade teeth into Oster® Blade Wash®
cleaning solution.
CAUTION: DO NOT IMMERSE THE CLIPPER.
4. Remove blade from cleaning solution and while holding clipper blade
end down, wipe the blades with a dry, clean cloth.
5. If after cleaning, you find that the blades still do not cut properly, it is
possible that a few fine pieces of hair are still trapped between the
blades.
6. If this occurs, remove the blade. Without loosening the tension springs
screws, slide the upper blade to one side but not completely out from
under the tension spring.
7. Wipe the surface between the blades clean with a dry cloth. Place a
drop of oil where the upper and lower blades meet and in the guide slot
of the tension spring.
8. Slide upper blade to the other side and repeat process.
Sharpening
Oster® cutting blades are of individual hollow-ground design, hardened to
extend cutting life. As with any cutting tool, the cutting edges will become
dull after extensive use. If sharpening is necessary, send blades to an Oster
Authorized Service Center.
Storing Your Clipper
Store your clipper in a clean, dry space. Be careful not to tangle the cord
while storing the clipper. Do not wrap cord around the clipper when storing.
This can damage the cord insulation.
OIL
Servicing of a Double Insulated Appliance
In a double insulated appliance, two systems of insulation are provided instead of
grounding. No grounding means is provided on a double-insulated appliance, nor
should a means for grounding be added. Servicing a double-insulated appliance
requires extreme care and knowledge of the system and should be done only by
qualified service personnel.
Replacement parts must be identical to those parts being replaced.
A double-insulated appliance is marked with the words “DOUBLE INSULATION” or
“DOUBLE INSULATED”
The symbol may also be marked on the appliance.
When using or cleaning this clipper, do not use any non Oster approved
aerosol sprays or blade washes, especially those containing methylene
chloride, dimethyl benzyl ammonium chloride, or 1-1-1 trichloroethylene.
Damage caused by these chemicals will void your warranty. You may use
®
Oster
Blade Wash® cleaner and Oster® Blade Lube™ oil, which do not
harm the product.
How To Obtain Warranty Service
™
Or an Authorized Service Center
Send this product to our Oster Direct® service center located at 904 Red Road,
McMinnville, TN 37110-8653 U.S.A. or to an authorized service center for Oster
®
Professional Products as indicated below:
In the U.S.A.
If you have any question regarding this warranty or would like to obtain warranty
service, please call 1 800 830-3678 and a convenient service center address will
be provided to you.
In Canada
If you have any question regarding this warranty or would like to obtain warranty
service, please call 1 800 830-3678 and a convenient service center address will
be provided to you. When sending the product to the service center:
• Fill out and attach the Service Information Form (found at the end of this
manual) to the Product.
• If returning a clipper, include blades.
• When ordering parts, please specify the model number and series letter
indicated on your product.
• Include a copy of the original sales receipt.
• Carefully package the product and send either mail or courier with shipping
and insurance prepaid to the service center.
WARRANTY: U.S. and CANADA: 1 Year Limited Warranty
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada,
Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions
(collectively “JCS”) warrants that for a period of one year from the date of purchase, this
product will be free from defects in material and workmanship. JCS, at its option, will
repair or replace this product or any component of the product found to be defective
during the warranty period. Replacement will be made with a new or remanufactured
product or component. If the product is no longer available, replacement may be made
with a similar product of equal or greater value. This is your exclusive warranty. Do NOT
attempt to repair or adjust any electrical or mechanical functions on this product. Doing
so will void this warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase
and is not transferable. Keep the original sales receipt. Proof of purchase is required to
obtain warranty performance. JCS dealers, service centers, or retail stores selling JCS
products do not have the right to alter, modify or any way change the terms and
conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the
following: negligent use or misuse of the product, use on improper voltage or current, use
contrary to the operating instructions, disassembly, repair or alteration by anyone other
than JCS or an authorized JCS service center. Further, the warranty does not cover: Acts
of God, such as fire, flood, hurricanes and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by the breach
of any express, implied or statutory warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or condition of
merchantability or fitness for a particular purpose is limited in duration to the duration of
the above warranty.
JCS disclaims all other warranties, conditions or representations, express, implied,
statutory or otherwise.
JCS shall not be liable for any damages of any kind Resulting from the purchase, use or
misuse of, or inability to use the product including incidental, special, consequential or
similar damages or loss of profits, or for any breach of contract, fundamental or
otherwise, or for any claim brought against purchaser by any other party.
Some provinces, states or jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages or limitations on how long an implied warranty lasts,
so the above limitations or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary
from province to province, state to state or jurisdiction to jurisdiction.
How to Obtain Warranty Service
In the U.S.A.
If you have any question regarding this warranty or would like to obtain warranty service,
please call 1 800 830-3678 and a convenient service center address will be provided to
you.
In Canada
If you have any question regarding this warranty or would like to obtain warranty service,
please call 1 800 830-3678 and a convenient service center address will be provided to
you.
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business as
Jarden Consumer Solutions located in Boca Raton, Florida 33431. In Canada, this
warranty is offered by Sunbeam Corporation (Canada) Limited doing business as Jarden
Consumer Solutions, located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. If
you have any other problem or claim in connection with this product, please write our
Consumer Service Department. PLEASE DO NOT RETURN THIS PRODUCT TO ANY
OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE.
For service, please contact:
North America:
Oster Direct® Services
904 Red Road, McMinnville, TN 37110
(800) 830-3678
or an Authorized Service Center
© 2012 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions.
All rights reserved. Distributed by Sunbeam Products, Inc. doing business as Jarden
Consumer Solutions, Boca Raton, Florida 33431. Printed in USA
GCDS-OST26509-AB PN 155512
10-76010_12EM1.indd 2 8/7/12 11:03 AM
Loading...