OSRAM SYLVANIA ENCELIUM User Manual

76-017-DB

11/13

OSRAM and Logo are registered trademarks of OSRAM

GmbH.

© 2013 O SRA M SYL VAN IA 0 1

-13

Important Safeguards

Overview

www.sylvania.com/encelium

Installation Notes

The Phase Cut Dimming Modules are to be installed in

dry,

indoor locations ONLY.

Troubleshooting

There are no user-serviceable parts inside of the Ph

ase Cut
Dimming Module. Please return the device to OSRAM
Sylvania Inc if service is required.

Regulatory Approvals

ote: This equipment has been tested and found to comply

N
with the limits for part 18 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct
the interference at his own expense.

Modifications not expressly approved by the manufacturer could
void the user's authority to operate the equipment under FCC
rules.

The contents of this Wiring and Installation Manual

are subject

to change without notice.

United States
OSRAM SYLVANIA

100 Endicott Street
Danvers, MA 01923
1-800-LIGHTBULB

Trade
Phone: [phone]
Fax: [phone]

National Accounts
Phone: [phone]
Fax: [phone]

OEM/Special Markets
Phone: [phone]
Fax: [phone]

Retail
Phone: [phone]
Fax: [phone]

SYLVANIA Lighting Services
Phone: [phone]
Fax: [phone]

Display/Optic
Phone: [phone]
Fax: [phone]

Canada
OSRAM SYLVANIA LTD.

2001 Drew Road
Mississauga, ON L5S 1S4
1-800-LIGHTBULB

Trade
Phone: [phone]
Fax: [phone]

OEM/Special Markets/Display/Optic
Phone: [phone]
Fax: [phone]

Retail
Phone: [phone]
Fax: [phone]

SYLVANIA Lighting Services
Phone: [phone]
Fax: [phone]

Mexico
OSRAM MEXICO

Tultitlan/Edo de Mexico
Phone: [phone]

ENCELIUM® Products
United States

Phone: [phone]
Fax: [phone]

Canada
Phone: [phone]
Fax: [phone]

www.sylvania.com

/Sylvania

/sylvania

™

ENCELIUM

Energy Management System

Phase Cut Dimming Module

Wiring and Installation Manual

The Phase Cut Dimming Module (PCDM) provides an
i

nterface between the Phase Cut dimmable (forward
and reverse phase) ballasts/LED drivers and the
ENCELIUM GreenBus II™ communication network.
The PCDM is automatically addressed as soon as it is
connected to an Energy Control Unit (ECU).
Individually addressable, the PCDM enables each
group or zone of fixtures to be independently
controlled and configured to best meet the needs of
the facility.

The PCDM is designed to control popular load types
such as Incandescent/Halogen lamps, Fluorescent
ballasts, LED fixtures, and LED/CF lamps. The phase
cut dimmable fixtures connected to a PCDM can then be controlled by any of the Encelium low voltage
wall station controllers, the Touch Screen panel or from Polaris 3D™ software through the GreenBus
II™ communication network. PCDM has a built-in relay which provides ON/OFF switching control in
addition to smoothly dimming the fixtures.

The following model is available:

ndoor Locations:

I

EN-PCDM-GB2

When using electrical equipment, basic safety precau

tions should always be followed

including the following:

• READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

• Do not let power supply cords touch hot surfaces.

• Do not mount near gas or electric heaters.

• Equipment should be mounted in locations and at heights where it will not readily be subjected to

tampering by unauthorized personnel.

• The use of accessory equipment is not recommended by OSRAM Sylvania as it may cause an

unsafe condition.

• Do not use this equipment for other than the intended use.

SAVE THESE INSTRUCTIONS

ENCELIUM and Polaris 3D are registered trademarks of OSRAM SYLVANIA, Inc
GreenBus II are trademarks of OSRAM SYLVANIA, Inc.
SEE THE WORLD IN A NEW LIGHT is a registered trademark of OSRAM SYLVANIA, Inc.

76-017-DB

11/13

OSRAM and Logo are registered trademarks of OSRAM

GmbH.

Phase Cut Dimm

ing Module

Installation

GreenBus II™ Wiring

Communication Circuit (24VDC, Class 2)

reenBus IITM is a low-cost, high reliability communication means to report sensor information back to

G
the ENCELIUM Energy Management System and to obtain optimum brightness settings for each
individual light fixture from the system – optimized to result in minimum energy costs for any given
building.

The GreenBus II

TM

wiring originates at an Energy Control Unit (ECU) and propagates in a daisy-chain or

“T” fashion from module to module (or other compatible equipment).

GreenBus II
GreenBus II

TM

uses proprietary connectors and jacks for ease of installation only.

TM

is a proprietary standard. Connect to ENCELIUM Energy Management System

only. Do not connect to other circuits.

Black – Line in
W

Earth Ground

hite – Neutral

Red – Relay output & Dim Control (connect to load)

Relay Contact; recommended relay
switching capacity 120VAC, 450W or
277VAC, 900W maximum

GreenBus II TM Communication
(Communication Circuit, Low Voltage)

Connect to ENCELIUM Energy Management System only. Do not connect to other circuits.

Maximum 100 total devices

GreenBus II

TM

must be laid out as per ENCELIUM EMS supplied drawing. If changes are required,
determine an optimum wiring path utilizing the supplied prefabricated cables, based on the position of
light fixtures and sensors. As the modules obtain power via the GreenBus IITM, the number of modules
on each chain is limited. It is suggested to leave room for future system upgrades and to limit the
number of modules per chain to 100 units during initial installation.

In a typical installation, Phase Cut Dimming Modules connect to Incandescent/Halogen lamps,
Fluorescent ballasts, LED fixtures, and LED/CF lamps that are capable of being dimmed via phase cut
method (forward and reverse phase).

The Phase Cut Dimming Module is typically connected to an individual or group of fixtures/lamps.

The mechanical construction allows for simple installation of the Phase Cut Dimming Module on top of a
standard square 4 11/16” junction box. Only a 4 11/16” junction box can be used, as the mounting
holes on the Phase Cut Dimming Module properly align with the holes on the junction box. ENCELIUM
GreenBus II™ communication wiring is still accessible from the outside of the junction box, while all
necessary wiring to the load (single or multiple ballasts/ LED fixtures) is done on the inside.

Wire as shown. Refer to local code, etc.

Refer to local code, etc.

Refer to local code, etc.Refer to local code, etc.

Absolute maximum load ratings

120VAC: 450W, 3.8A max
277VAC: 900W, 3.3A max

Due to the internal relay, power feed to module may be live even if lights are off. Turn off
power at circuit breaker or fuse before installing or servicing module. Observe lockout
procedures.

ENCELIUM and Polaris 3D are registered trademarks of OSRAM SYLVANIA, Inc
GreenBus II are trademarks of OSRAM SYLVANIA, Inc.
SEE THE WORLD IN A NEW LIGHT is a registered trademark of OSRAM SYLVANIA, Inc.