OSRAM PL T4 NSB Technical data

Blaue Laser Diode in TO38 ICut Bauform Blue Laser Diode in TO38 ICut Package
PL T4 NSB
Besondere Merkmale
Typ. Emissionswellenlänge 450nm
Effiziente Strahlungsquelle für Dauerstrich- und gepulsten Betriebsmodus
Hohe Modulationsbandbreite
Miniaturisiertes TO38 ICut Gehäuse
Laserdiode isoliert gegen Gehäuse
Anwendungen
Laserprojektion
Instrumentierung
Bio- und Medizintechnik
Holographie
Messtechnik
Sicherheitshinweise
Je nach Betriebsart emittieren diese Bauteile hochkonzentrierte, sichtbare Strahlung, die gefährlich für das menschliche Auge sein kann. Produkte, die diese Bauteile enthalten, müssen gemäß den Sicherheitsrichtlinien der IEC-Norm 60825-1 behandelt werden.
Features
Typ. emission wavelength 450nm
Efficient radiation source for cw and pulsed operation
Single transverse mode semiconductor laser
High modulation bandwidth
Miniaturized TO38 ICut package
Laser diode isolated against package
Applications
Laser projection
Instrumentation
Biomedical Applications
Holography
•Metrology
Safety Advice
Depending on the mode of operation, these devices emit highly concentrated visible light which can be hazardous to the human eye. Products which incorporate these devices have to follow the safety precautions found in IEC 60825-1 “Safety of laser products”.
2009-08-04 1
PL T4 NSB
Typ Type
Opt. Ausgangsleistung Optical Output Power
1)
1)
Bestellnummer Ordering Code
Pop (mW)
PL T4 NSB 50 Q65110A8642
Grenzwerte
Betrieb ausserhalb dieser Bedingungen kann das Bauteil schädigen
Maximum Ratings
Operation outside these conditions may damage the device
Bezeichnung Parameter
Symbol Symbol
min. max.
Max. Opt. Ausgangsleistung Max. Optical Output Power
Betriebsstrom
1)2
1)2)
)
P
I
F
opmax
–80mW
120 mA
Operating Current Betriebstemperatur
T
Case
+ 10 + 70 °C
Operating Temperature
Wert
Values
Einheit Unit
Lagertemperatur
T
stg
Storage Temperature Sperrspannung
V
R
Reverse Voltage Löttemperatur max. 10 sec.
T
solder
Soldering Temperature max. 10 sec.
1)
Optische Leistungsmessungen beziehen sich auf eine Messung mittels Ulbrichtkugel Optical power measurements refer to an integrating sphere
2)
Maximal erlaubte optische Ausgangsleistung bei allen Betriebsbedingungen. Maximum allowed optical output power at all allowed operating condition s.
- 40 + 85 °C
–2V
260 °C
2009-08-04 2
PL T4 NSB
Laserkennwerte (T
= 25 °C)
case
Laser Characteristics Bezeichnung
Parameter
Zentrale Emissionswellenlänge Emission Wavelength
3)
3)
Spektrale Breite (Halbwertsbreite) Spectral Width (FWHM)
3)
Schwellstrom Threshold Current
Betriebsstrom Operating Current
Betriebsspannung Operating Voltage
Strahldivergenz (FWHM) Beam Divergence (FWHM)
Polarisation Polarization
3)
3)
3)
3)
3)
3)
3)
3)
Symbol Symbol
Wert
Values
Einheit Unit
min. typ. max.
λ
peak
3)
Δλ –2–nm
I
th
I
F
V
F
440 450 460 nm
–3060mA
80 120 mA
–5.56.5V
4x15 7x21 15x25 deg
θ
× θ
||
P
gr
20:1
Modulationsfrequenz
f –>100–MHz
Modulation Frequency
3)
Standardbetriebsbedingungen beziehen sich auf Pop=50mW Ausgangsleistung. Standard operating conditions refer for to an output power of Pop=50mW
2009-08-04 3
PL T4 NSB
Optische Ausgangsleistung Optical Output Power
P
= f (IF)
opt
50
mW
P
40
opt
T
30
T
case
T
case
= 40°C
case
= 60°C
= 20°C
20
10
0
0 20406080100
mA
Betriebsspannung Operating Voltage
V
= f (IF)
F
6,0
V
5,0
V
F
T
4,0
3,0
T
case
T
case
= 60°C
= 20°C
case
= 40°C
2,0
1,0
0,0
0 20406080100
I
F
mA
I
F
Schwellstrom Threshold Current
I
= f (T
th
Case
)
36
mA
34
I
th
32
30
28
26
24
22
20
10 30 50 70
°C
T
Case
Zentrale Emissionswellenlänge Emission Wavelength
λ
= f (T
Case
)
T
= 40°C
case
1,0
Relative
P
opt
0,8
T
case
0,6
T
case
= 20°C
0,4
0,2
0,0
442 444 446 448 450
nm
= 60°C
λ
2009-08-04 4
Strahldivergenz Beam Divergence
P
= f (θ ), T
opt
Case
= 25°
PL T4 NSB
C
Relative
P
opt
1,0
0,8
0,6
θ
0,4
θ
0,2
0,0
-60 -40 -20 0 20 40 60
||
deg
θ
2009-08-04 5
PL T4 NSB
Wichtige Hinweise zum Betrieb der Laserdiode:
a) Lasersicherheit: Die Laserdiode wurde in Klasse 3B gemäß der IEC-Norm 60825-1 eingruppiert. Die von der
Laserdiode tatsächlich emittierte Strahlung hängt in erster Linie von den Betriebsbedingungen ab.
b) Elektrischer Betrieb:
OSRAMs Laserdioden sind mit dem Ziel höchster Leistung und Zuverlässigkeit gefertigt. Der Betrieb der Laserdiode oberhalb der im Datenblatt angegebenen Maximalwerte kann jedoch die Leistung und die Zuverlässigkeit erheblich beeinträchtigen. Daher sollte die Laserdiode auch mit einer möglichst rauscharmen Stromversorgung betrieben werden. Die Laserdiode ist sehr empfindlich gegenüber elektrostatischen Entladungen (ESD). Entsprechende Vorsichtsmaßnahmen sind zu treffen.
Important notes of operation for laser diode:
a) Safety of laser product: The laser diode is classified in class 3B acc. IEC 60825-1. The actual laser light emitted by the laser
diode strongly depends on the mode of operation.
b) Electrical operation:
OSRAMs laser diodes are designed for maximum performance and reliability. Operating the laser diode above the maximum rating even for very short periods of time can damage the laser diode or reduce its lifetime. The laser diode must be operated with a suitable power supply with minimized electrical noise. The laser diode is very sensitive to electrostatic discharge (ESD). Proper precautions must be taken.
c) Verarbeitungshinweise: Ein geeignetes Wärmemanagement ist ausschlaggebend für eine lange Lebensdauer der Laserdiode. Auf Grund des Designs wird die in der Diode erzeugte Wärme haupsächlich über die Grundplatte des Gehäuses abgeführt. Es muss sichergestellt sein, daß eine ausreichend gut wärmeleitende Verbindung zwischen der Diodengrundplatte und dem Kühlkörper besteht.
c) Mounting instructions:
In order to maintain the lifetime of the laser diode proper heat management is essential. Due to the design of the laser diode heat is dissipated only through the base plate of the diode‘s body. A proper heat conducting interconnection between the diodes base plate and the heat sink must be maintained.
2009-08-04 6
Maßzeichnung Package Outlines
PL T4 NSB
Maße in mm / Dimensions in mm
Pinbelegung Pin Connection
Pin 1 LD Anode Pin 2 Case Pin 3 LD Cathode
2009-08-04 7
PL T4 NSB
Published by OSRAM Opto Semiconductors GmbH
Leibnizstrasse 4, D-93055 Regensburg
www.osram-os.com
© All Rights Reserved.
The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization.
Packing
Please use the recycling operators known to you. We can also help you ge t in touch with your neares t sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred.
Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components, may only be used in life-support devices or systems with the express written approval of OSRAM OS.
A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affec t its safety or e ffectiveness of that dev ice or system.
Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health of the user may be endangered.
2009-08-04 8
PL T4 NSB
Revision History:
Previous Version:
Page Subjects (major changes since last revision) Date of change
2009-08-04 9
Loading...