Osram EN-WS-2B-GB2-WH, EN-WS-SC5-GB2-WH, EN-WS-ZC3-GB2-WH, EN-WS-SC3-GB2-WH, EN-WS-ZC6-GB2-WH Wiring And Installation Manual

Low-Voltage Wallstations

Wiring and installation manual

www.osram.us

Light is OSRAM

Overview

The Low-voltage Wallstations with integrated LED indicators are available in a
range of configurations for customized light level control. This low-voltage Wall­station obtains its operating power via GreenBus II® cable and features several
options for functionality depending on the model installed.

The low-voltage wallstation obtains its address during the commissioning
process and no actions are required during installation.

Important Safeguards

Note

Tip

!

STOP

When using electrical equipment, basic safety precautions should always
be followed including the following:

— READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

— Do not mount near gas or electric heaters.

— Equipment should be mounted in locations and at heights where it will not

readily be subjected to tampering by unauthorized personnel.

— The use of accessory equipment is not recommended by OSRAM as it may

cause an unsafe condition.

— Do not use this equipment for other than the intended use.

Note

Tip

!

STOP

SAVE THESE INSTRUCTIONS

Low-voltage Works with ENCELIUM® Works with ENCELIUM EDGE™
Wallstation Ordering Code EXTEND Networked LMS Standalone LMS

2-But ton EN-W S-2B-GB2-WH X X
3-Scene EN-W S-SC3-GB2-W H X X
5-Scene EN-WS-SC5-GB2-WH X X
3-Zone EN-W S-ZC3-GB2-WH X
6-Zone EN-W S-ZC6 -GB2-WH X

2

GreenBus II® Wiring

Communication Circuit: 24Vdc, Class 2

GreenBus II is a low-cost, high reliability communication standard used to report
occupancy status signals, daylight readings and user inputs received via Wallstations
to the ENCELIUM® EXTEND Networked Light Management System or the
ENCELIUM EDGE™ Standalone Wireless Light Management System for
the purpose of obtaining optimum brightness settings for an individual light
fixture or a group of light fixtures.

When used in the ENCELIUM EXTEND Networked Light Management System, the
GreenBus II wiring originates at an ENCELIUM EXTEND Manager and propagates in
a daisy-chain or “T” fashion from device to device (or other compatible equipment).

When used in the ENCELIUM EDGE Standalone Wireless Light Management
System, the GreenBus II wiring is used to connect a low-voltage wallstation directly
to a Wireless Area Light Control Module (WALC).

Note

Tip

!

STOP

GreenBus II is an proprietary standard and proprietary connectors and jacks
are used for ease of installation only.

Connect to the ENCELIUM EXTEND Networked Light Management System
or the ENCELIUM EDGE Standalone Wireless Light Management System
only. DO NOT CONNECT TO OTHER CIRCUITS.

GreenBus II must be laid out as per
supplied system layout drawing. If changes
are required, determine an optimum wiring
path utilizing the supplied prefabricated
cables, based on the position of light
fixtures, sensors and Wallstations. The
number of modules on each chain is
limited since the modules obtain power
via the GreenBus II cable.

Notes

— When used in the ENCELIUM EXTEND

Networked Light Management System,
it is suggested to leave room for future
system upgrades and to limit the
number of modules per GreenBus II
channel to 80 during initial installation.

GreenBus II wires can be inserted
into either of the 2 ports. Press the
corresponding button to insert the wires.

— Both ports may be used when connecting in a daisy-chain fashion

(e.g. ENCELIUM EXTEND Networked Light Management System device).
To remove the wires, press the corresponding button and pull the wires out
while rotating them in a circular motion.

3

Push Button
Terminal Block

*Pair 2

*Pair 1

Faceplate

GreenBus II wires (Pairs 1 & 2) should not be crossed.

GreenBus II wires are polarity independent.

A shor t GreenBus II jumper can be used to interconnect
ganged wallstations.

Mounting bracket Old Work Low Voltage
Mounting Bracket

Low Voltage Device Box:

4

Mounting bracket J-Box

Wallstation Installation

Electrical Metal Device Box:

Install the mounting bracket using the supplied screws. Ensure that the OSRAM
logo and SINGLE GANG labels are facing up.

Decorator Plate Installation

The low-voltage wallstation can also be installed with an off-the-shelf
decorator-style wall plate. Multi-gang wallstation installations require
multi-gang decorator wall plates.

Remove the button assembly from the OSRAM wall plate. This can be achieved
by pressing the wall plate with your thumbs near the button assembly while
grasping the OSRAM Wall Plate.

5

Wallstation Installation (continued)

Place the wallstation assembly into the mounting plate and push gently until
‘clicks’ are heard. This confirms that the pieces are secured.

Orient the mounting bracket such that the DECORATOR and MULTI GANG
labels are facing up. Insert the wallstation button assembly into the mounting
plate until ‘clicks’ are heard. Clicks confirm that the pieces are secured.

Install the mounting bracket using the supplied screws. Install the decorator
plate using screws supplied with the decorator plate.

6

Decorator Plate Installation (continued)

Install the supplied wall strips to the button assembly until they snap in.

Installation Notes

Consult the OSRAM website for the most up-to-date version of the GreenBus II®
system design guide and install this product according to the guidelines.

The Wallstation is to be installed in dry, indoor locations ONLY. Do not install
the Wallstation in damp locations. Damp locations are defined as: interior
locations subject to moderate degrees of moisture, such as basements,
barns, cold-storage warehouses, as well as partially protected locations
under canopies, marquees and open roofed porches.

Troubleshooting

There are no user-serviceable parts inside the Wallstation. Please return the
device to OSRAM if service is required.

Regulatory Approvals

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

Modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment under FCC rules.

This equipment has been tested and found to comply with Industry Canada
ICES-003 Issue 5 (CAN ICES-3 (A)/NMB-3(A)).

Contains FCC ID: H79DFZM-E7220
Contains IC ID: 4259B-DFZM7220

7

© 2018 OSRAM SYLVANIA Inc.

LM S135R 2 4-18

OSRAM SYLVANIA Inc.

200 Ballardvale Street

Wilmington, MA 01887 USA

888-531-7573

www.osram.us/ds

OSRAM is a registered tradema rk of OSR AM GmbH.
ENCELIUM EXTEND and GreenBus II are registe red trademar ks of OSRAM SYLVANIA Inc.
ENCELIUM EDGE is a tradem ark of OSRAM SYLVANIA Inc.
Specifications subject to change without notice.