OSRAM EASY RC User Manual

EASY RC

Radio receiver
Operating instructions

Description

Purpose and application

The EASY RC radio receiver is used to receive wireless radio
signals from EASY hybrid remote hand-held transmitters or
EASY Color Drive wall operating units and transmit these to

EASY control units.

The radio receiver can be installed in luminaires or, with the
optional ECO CI KIT, in suspended ceilings.

Function

The radio receiver converts the radio signals of the hand-held
transmitters and wall operating units into the corresponding
telegrams and transmits them through wires to the connected

EASY control units.

The radio receiver is supplied directly from the EASY signal line
and can be connected anywhere in the EASY signal line.

Construction

A

The radio receiver is made up of the following components:

• LED (A)

• Connections for EASY signal:

– Modular 4p4c socket (B)

– 4-pin plug-in terminal (C)

• „Connect“ button for training and untraining hand-held trans­mitters/wall operating units (D)

Operation

DBC

Training hand-held transmitters/wall
operating units

E

F

Up to 8 EASY hybrid remote hand-held transmitters or EASY
Color Drive wall operating units can be trained into the radio
receiver. If this number is exceeded, the oldest connection is

automatically deleted.

Note: To operate the hand-held transmitters and wall operating
units, see the separate instructions.

Activate the radio transmission of the hand-held transmitter



or wall operating unit.

Press the „Connect“ button of the desired hand-held trans-



mitter or wall operating unit.

• Wall transmitter (E): lower part of housing

• Hand-held transmitter (F): battery compartment

The display of hand-held transmitter/wall operating unit

shows „Connecting“.

Press the „Connect“ button (D) of the radio receiver within



the next 30 seconds.

The LED (A) of the radio receiver ashes orange.

Training was successful:

• The display of the hand-held transmitter/wall operating

unit shows „Success“.

• The LED of the radio receiver lights up green.

Training failed:

• The display of the hand-held transmitter/wall operating

unit shows „Not linked“ or „No RF link“.

• The LED of the radio receiver lights up red.

Press the „Connect“ button on the radio receiver and hand-



held transmitter/wall operating unit to end the training mode.
The training mode is ended automatically after 30 seconds.

VIII 2009

EASY-RC_ba0908en_we1.01.indd

OSRAM GmbH
Kunden Service Center
Customer-Service-Center (CSC)

Steinerne Furt 62
86167 Augsburg
Germany

Tel : [phone] - 200
(kostenpichtig / charges apply)
Fax.: [phone] - 202

www.osram.com

www.osram.de

40083214217776

4008321421777

Untraining the hand-held transmitter/
wall operating unit

Press the „Connect“ button (D) of the radio receiver for 10

seconds.

Activation: The LED (A) of the radio receiver lights up red.

Page 1 of 2

Appendix

Technical data

Operating temperature 0 °C ... +50 °C

Transmission power 10 mW

Radio signal Frequency band 868.3 MHz

FSK digital signal (OSRAM-

specic coding)

Functional range In the open air: approx. 100 m

In buildings: approx. 30 m

Permissible conductor
cross-section when connec­ted via terminals

Max. number of

wall/hand-held transmitters

Protection class III

Protection type IP 20

Dimensions

(L x W x H)

Single-wire conductor
(AWG 26 – AWG 20):

0.13 - 0.5 mm²

Fine-wire conductor
(AWG 24 – AWG 20):

0.2 - 0.5 mm²

8

118 x 30 x 21 mm

Disposal

Do not dispose of the device with household waste.

Electronic devices must be disposed of at local
recycling centres for waste electronic equipment in

accordance with EU Directive 2002/96/EC on waste

electrical and electronic equipment.

Conformity with the relevant EU directives is
conrmed by the CE symbol.

Page 2 of 2