Data Sheet
COINlight®
CM01E
Picture for
Datasheet
Benefits
¾
Low profile
¾
Wide viewing angle
¾
Easy installation
¾
Available in various colors
is missing
!!!
Applications
¾
Border marker
¾
In-ground mounted luminaires
¾
Small signals
Technical Operating Data
Product
All Data are related to the entire module
*)
Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily
correspond to the actual parameters of each single product which could differ from the typical data.
Color Voltage
white 24 1,2 120 5400 K 160,05CM01E-W2-854 9
red 24 1,0 120 617 nm 110,04CM01E-A1 9
yellow 24 1,0 120 587 nm 70,04CM01E-Y1 9
green 24 1,2 120 525 nm 160,05CM01E-T2 9
blue 24 1,2 120 470 nm 10,05CM01E-B1 9
Number of
LEDs
[V DC]*
Power
[W]*
Current
[A]*
Radiance
Angle [°]*
Wavelength [nm]
Color Temp [K]*
Technical Features
Circular LED spot with 9 LED
¾
Diameter of the module: Ø 33 mm
¾
Very low profile (< 7mm)
¾
Light emission vertical to the mounting surface
¾
Viewing angle 120° per LED
¾
Connection with screw terminals
¾
Only parallel connection allowed
¾
Dimmable by pulse width modulation (PWM)
¾
with the electronic controller OT DIM
Diverse OPTOTRONIC® controllgear with
¾
1..10V, DALI, DMX or EASY protocoll available
Modules optimized for use with OSRAM
¾
OPTOTRONIC® power supplies.
Lum. Flux
[lm]*
CM01E - 01.06.2007
Page 1 of 4
Minimum and Maximum Ratings
Product Voltage Range
CM01E-W2-854 23 25 25...-30 75 -40 85... ...
CM01E-A1 23 25 25...-30 85 -40 85... ...
CM01E-Y1 23 25 25...-30 85 -40 85... ...
CM01E-T2 23 25 25...-30 75 -40 85... ...
CM01E-B1 23 25 25...-30 75 -40 85... ...
Exceeding maximum ratings for operation and storage temperature will reduce expected life time or destroy the LED Module.
*)
Exceeding maximum ratings for operation voltage will cause hazardous overload and will likely destroy the LED Module.
The temperature of the LED module needs to measured at the Tc-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature
sensitive label. For exact location of the Tc-point see drawing below.
Operating Temperature
at Tc-Point [ °C ] *
Storage Temperature
[ °C ] *
[ V dc ] *
Reverse Voltage
[ V dc ] *
Drawing
Drawing is missing !!!
CM01E - 01.06.2007
Page 2 of 4
Safety Information
¾
The LED module itself and all its components may not be mechanically stressed.
¾
Assembly must not damage or destroy conducting paths on the circuit board.
The LED Module incorporates no protection against short circuits, overload or overheating. Therefore it is absolutely necessary to
operate the modules with a electronically stabilised power supply offering protection against the above mentioned safety risks.
For dimming applications attention should be paid to specific references in "OPTOTRONIC ® Technical Guide".
OSRAM OPTOTRONIC ® power supplies are specifically designed with protection features for safe operation.
When using power supplies other than OPTOTRONIC ® the following basic safety features are required, in addition to any other
application specific concerns and local safety codes:
¾
Short circuit protection
¾
Overload protection
¾
Overheat protection
¾
Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards.
Only qualified personnel should be allowed to perform installations.
¾
Correct electrical polarity needs to be observed. Wrong polarity will result in no light emission.
¾
Parallel connection is highly recommended as safe electrical operation mode.
Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and damage the LED module.
¾
Pay attention to ESD steps when mounting the module
¾
The module, as manufactured, has no conformal coating and therefore offers no inherent protection against corrosion.
¾
Damage by corrosion will not be honored as a materials defect claim. It is the user's responsibility to provide suitable protection
against corrosive agents such as moisture and condensation and other harmful elements.
¾
For applications involving exposure to humidity and dust the module must be protected by a fixture or housing with a suitable
protection class. The module can be protected against condensation water by treatment with an appropriate circuit board grade
conformal coating. The conformal coating should have the following features:
- Optical transparency
- UV-resistance
- thermal expansion matching the thermal expansion of the module 15-30*10^-6 cm/cm/K
- low permeability of steam for all climatic conditions
- resistance against corrosive environment
The lacquer APL of the company Electro lube http://www.electrolube.com met the conditions for the COINlight® in our tests.
CM01E - 01.06.2007
Page 3 of 4
Assembly Information
Rotation fixing by milled groove.
¾
Between bottom side and fixture housing should be an effective thermal contact.
¾
Ordering Guide
Productgroup Productname EAN *
COINlight® CM01E-W2-854 4008321040107 25
COINlight® C M01E-A1 4050300857534 25
COINlight® C M01E-Y1 4050300947938 25
COINlight® C M01E-T2 4008321132642 25
COINlight® C M01E-B1 4050300947891 25
EAN: Ordering number per single module
*)
S-Unit: Modules per shipping unit
Note: Typical performance data are subject to change without any further notice, particularly as LED technology evolves.
S-Unit *
Sales and Technical Support
OSRAM GmbH
Hellabrunner Strasse 1
D - 81536 München
Germany
www.osram.com
+49 (0)89 6213-0
Sales and technical support is given by the
local OSRAM subsidiaries.
On our world wide homepage all OSRAM
subsidiaries are listed with complete
address and phone numbers.
Related and Further Information
¾
The new dimension of light
¾
OPTOTRONIC® Technical Guide
¾
OPTOTRONIC® Data Sheets
¾
OSRAM LED systems
153 S006 GB
130 T008 GB
http://catalog.myosram.com
www.osram.com/led-systems
CM01E - 01.06.2007
Page 4 of 4
Loading...