OSP XT82L Operating Instructions Manual
XT82L
L-SHAPED DESK
OPERATING INSTRUCTIONS
WarnInG
1. Do not use this product unless all screws and bolts are securely
tightened.
2. Check that all screws and bolts are tight every three months or as
needed.
3. Dispose of packing material properly. Do not use plastic cover as
head covering. It may cause suffocation.
4. Do not use this product as a stepladder.
5. Use this product for its intended purpose only.
LIMITED WarranTy
OSP Designs Warrants, to the original purchaser its products to be free from defects in material and workmanship for a period of 90 days. Defects
and damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other event beyond the control of OSP
Designs is not covered. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or consequential
damages is excluded. The user assumes all risk of injury resulting from use of this product. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
To make a warranty claim, contact Customer Service, provide model number, sales receipt and description of the problem. It is the customer’s
responsibility to prepay freight on any components returned to the factory. OSP Designs will pay return freight on components covered under
terms of warranty.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when hardware is missing.
Our Parts Department will do everything possible to promptly remedy the problem. Contact us via email parts@officestar.net, by Fax
1-909-930-5629, or toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time. OSP Designs P.O. Box
3520 Ontario, California 91761 USA
6. Intended for residential use only.
XT82L
XT82L
IMPORTANT NOTE:
1. Use hand tools only for assembly as power tools may
cause damage
2. Carefully remove any staples used for packaging.
3. Phillips Screwdriver also needed for assembly
(not provided)
STEP 1
18
10R
10L
L-SHAPED DESK
ASSEMBLY INSTRUCTIONS
PART QTY
1. Desk Top (1L & 1R) ............2
2. Corner Top ..................1
3. Keyboard ....................1
4. Back Panel ..................2
5. Back Rail ....................2
6. Wooden Leg (6L & 6R) .........4
7. Metal Leg ....................4
8. Bottom Metal Rail .............2
9. Top Metal Rail ................2
10. Slide (10L & 10R) ............2
11. Metal Plate ..................4
PART QTY
12. Metal L-Bracket ..............4
13. Cam Lock ..................6
14. Cam Lock Stud ..............6
15. Cam Cap ...................6
16. Short Bolt ..................24
17. Long Bolt ..................24
18. Short Screw ................12
19. Medium Screw ...............4
20. Long Screw .................8
21. Wooden Dowel ..............6
22. Sticker ....................12
23. Allen Wrench (not shown) ......1
STEP 3
6R
7
STEP 4
17
L-SHAPED DESK
ASSEMBLY INSTRUCTIONS
6L 6R
8
7
9 9
5
20
22
8
7
5
17
1L
STEP 2
9
1L
14
7
1R
6L
6R 6L
STEP 5
7
17
17
9
6L
5
13
15
5
1R
6R
7
7
17
18
8
5 5
3
20
17
22
7
8
Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.
STEP 1 Insert three Cam Lock Studs (14) into Desk Tops (1L & 1R). Attach Slides (10L 7 10R) using two Short Screws (18) for each Slide (10).
FULLY TIGHTEN ALL CAM LOCK STUDS (14) AND SHORT SCREWS (18) USING PHILLIPS SCREWDRIVER (not provided).
STEP 2 Attach one Back Rail (5) to each Desk Top (1) and secure using three Cam Locks (14) for each Back Rail (5), FULLY TIGHTEN ALL CAM
LOCKS (13) USING PHILLIPS SCREWDRIVER (not provided). Cover Cam Locks (13) using six Cam Caps (15). Attach one Top Metal
Rail (9) to each Desk Top (1) using two Long Bolts (17) for each Top Metal Rail (9). FULLY TIGHTEN ALL LONG BOLTS (17) USING
ALLEN WRENCH (23).
STEP 3 Attach two Metal Legs (7) to both Wooden Legs (6L & 6R) using two Long Bolts (17) for each Metal Leg (7). FULLY TIGHTEN ALL LONG
BOLTS (17) USING ALLEN WRENCH (23).
STEP 4 Secure Wooden Legs (6L & 6R) to Back Rails (5) using two Long Screws (20) for each Wooden Leg (6L & 6R), secure Metal Legs (7) to Top Metal
Rails (9) using one Long Bolt (17) for each Top Metal Rail (9). Attach Bottom Metal Rails (8) to Metal Legs (7) using one Long Bolt (17) for each Metal Leg (7).
FULLY TIGHTEN ALL LONG BOLTS (17) USING ALLEN WRENCH (23), FULLY TIGHTEN ALL LONG SCREWS (20) USING
PHILLIPS SCREWDRIVER (not provided). Cover holes of Long Screws (20) using four Stickers (22).
STEP 5 REPEAT STEP 4 FOR REMAIING WOODEN LEGS (6L & 6R). Attach Keyboard (3) to Slides (10L & 10R) using
four Short Screws (18).
FULLY TIGHTEN ALL SHORT SCREWS (18) USING PHILLIPS SCREWDRIVER (not provided).
Loading...