Ositech 614006-001 User Manual

Trumpcard Ethernet LAN

User’s Guide and Reference

Cop y right

Information in this document is subject to change without notice.

Copyright 1995-1997 by Ositech Communications Inc., Guelph,
Ontario, Canada.

Ositech Communications Inc. shall not be liable for technical or editorial
errors or omissions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of this
material.

Trumpcard is a trademark of Ositech Communications Inc.
P/N: 614006-001 Revision 3.0

How To Contact Us

At Ositech Communications, we make every effort to provide our
customers with products that fit their needs and work well. If you wish to
communicate with technical support, sales, or any other department at
Ositech, please contact us in one or more of the following ways:

Ositech Communications Inc.
679 Southgate Drive
Guelph, Ontario, Canada
N1G 4S2

Toll Free Telephone: 1-888-OSITECH (1-888-674-8324)
Local Telephone: [phone]
Facsimile: [phone]

24 HR Bulletin Board Service
[phone]
[8-N-1, up to 33.6 KBPS]

Internet: World Wide Web http://www.ositech.com

FTP ftp.ositech.com
E-Mail [e-mail]

[e-mail]

ii

Preface

This guide provides Network software installation instructions for the
Ositech Trumpcard

The Trumpcard Ethernet LAN PC Card is a PCMCIA Type II PC Card that
can connect to 10BaseT (unshielded twisted pair) or 10Base2 (thin coax)
Ethernet Networks. The Ethernet LAN is available separately or combined
with other functions. This guide only describes the Ethernet LAN function
of a single or multi-function Trumpcard; if your Trumpcard is multi-function,
refer to the

‘Trumpcard’, ‘Trumpcard LAN’, ‘Trumpcard Ethernet LAN’ and ‘Trumpcard
Ethernet LAN PC Card’ will be used interchangeably throughout this
manual. All refer to the Ositech Trumpcard Ethernet LAN PC Card.

‘PCMCIA Card’ and ‘PC Card’ will be used interchangeably throughout
this manual. As above, both terms refer to the Ositech Trumpcard
Ethernet LAN PC Card.

Ethernet LAN PC Card.

Installation Guide

accompanying the PC Card for more details.

iii

FCC Notice

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception (which can be determined by
turning the equipment off and on), the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.

• Consult the dealer or an experienced radio or television technician
for help.

Modifications

The FCC requires the user to be notified that any changes or
modifications made to this device, that are not expressly approved by
Ositech Communications Inc., may void the user’s authority to operate this
equipment.

Operating Conditions

This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including
interference that may cause undesired operation.

Canadian Electromagnetic Compatibility Advisory

This Class B digital apparatus meets all requirements of the Canadian
Interference Causing Equipment Regulations.

Conseil sur la compatibilité des Electromagnétiques,
pour le Canada

Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.

iv

Contents

Section One

Introduction 1-1

Section Two

Hardware Installation 2-1

Preparing for Installation ...................................................................................... 2-1

Installing the Trumpcard LAN .......................................................................... 2-2

Connecting to 10BaseT Twisted Pair Networks ................................................ 2-3

Interface Cabling and Pinout ........................................................................... 2 -5

Concentrators ...................................................................................................2-6

Twisted Pair Ethernet Network Characteristics .............................................. 2-6

Connecting to 10Base2 Thin Ethernet Networks ............................................... 2 -7

Thin Coax Ethernet Segment...........................................................................2-8

Thin Ethernet Network Characteristics ......................................................... 2-10

Media Access Module LED Indicators ..............................................................2-11

Section Three

Operation 3-1

Socket Services and Card Services .................................................................... 3-2

Multi-Function Configuration ............................................................................... 3-2

Network Software Installation .............................................................................. 3- 3

Banyan VINES .................................................................................................. 3-3

DEC PATHWORKS .......................................................................................... 3-4

FTP Software LanWatch................................................................................... 3- 5

IBM LAN Server ................................................................................................ 3-6

IBM LAN Support Program...............................................................................3-8

Microsoft LAN Manager ..................................................................................3-10

v

Microsoft Windows for Workgroups ............................................................... 3-11

Microsoft Windows NT 3.5 .............................................................................3-13

Microsoft Workgroup Connection for DOS .................................................... 3-13

NDIS (Generic) ...............................................................................................3-15

Novell Netware for DOS .................................................................................3-16

Novell Netware for OS/2 ................................................................................. 3-17

Novell Unixware DLPI Driver ......................................................................... 3-19

SCO UNIX LLI Driver......................................................................................3-20

Section Four

Appendices 4-1

APPENDIX A – ODI Keywords ............................................................................. 4-2

NET.CFG Example ........................................................................................... 4-5

APPENDIX B – NDIS Keywords .......................................................................... 4-6

PROTOCOL.INI Example ................................................................................. 4 -8

APPENDIX C – MESSAGES.................................................................................4-9

WARNING MESSAGES.....................................................................................4-9

ERROR MESSAGES......................................................................................... 4-9

ODI Specific Error Messages ........................................................................ 4-12

NDIS Specific Error Messages ...................................................................... 4-12

vi

Introduction

Section One

Introduction

Congratulations on your choice of an Ositech Trumpcard Ethernet LAN
PC Card! We believe you will find it a superior quality product that will
meet or exceed your Networking needs.

The Trumpcard Ethernet LAN PC Card is a convenient, dual-media,
credit-card sized adapter that provides an interface between a PCMCIA
capable computer and an Ethernet Network.

Direct connection to a 10BaseT Network is possible via a 10BaseT
PCMCIA cable only. For 10Base2 connections, a Media Access Module is
required. Two styles of connectors are provided on the Media Access
Module, enabling connection to the Network using RJ-45 to connect to
10BaseT, or BNC to connect to 10Base2.

Note: This manual is intended as a supplement to the manual(s) supplied

with your Network system software. Use that document as the primary
reference source for information about your Network.

Software installation instructions are given in Section Two for connecting
to:

Banyan VINES
DEC PATHWORKS
FTP Software LanWatch
IBM LAN Server
IBM LAN Support Program
Microsoft LAN Manager
Microsoft Windows for Workgroups
Microsoft Windows NT
Microsoft Workgroup connection for DOS
NDIS (Generic)
Novell Netware for DOS
Novell Netware for OS/2
Novell Unixware
SCO Unix

User’s Guide and Reference 1 - 1

Section One

1 - 2 Trumpcard Ethernet LAN

Section Two

Hardware Installation

Unpack the Trumpcard Ethernet LAN hardware, and follow the steps
listed below to install it on your computer. Instructions are included for
both 10BaseT twisted-pair and 10Base2 thin coax Ethernet Network
operations.

Preparing for Installation

To install the Trumpcard, you require the accompanying diskettes and the
following items:

• A computer equipped with a PCMCIA Release 2.0, Type II PC
Card slot.

• PCMCIA Card and Socket Services Version 2.x or higher,
installed. This is optional since the Trumpcard can be operated
without Card and Socket Services.

Hardware Installation

• A Network operating system that is supported by the Trumpcard
Network drivers.

• For 10Base2 (thin coax) Networks, a coaxial T-connector and a
terminator if at the end of the coaxial segment.

• For 10BaseT (twisted pair) Networks, a twisted pair Network cable
terminated with an RJ-45 connector when using the Media Access

Module for 10BaseT connections.

User’s Guide and Reference 2 - 1

Section Two

Installing the Trumpcard Ethernet LAN

The Trumpcard Ethernet LAN can be inserted into a computer whether the
power is ON or OFF.

Follow these steps:

• Orient the Trumpcard so that the 68-pin connector is next to the

PCMCIA slot of the computer.

• Insert the Trumpcard into the slot until it is firmly seated.

Note: These are general installation instructions that apply to most

computers. Please refer to the manual accompanying your computer
for any additional instructions on installing PC Card adapters.

Note: The Trumpcard is keyed to go in one way only. If you feel resistance

before it is fully inserted, remove it, turn it over, and re-insert it.

Installing the Trumpcard

2 - 2 Trumpcard Ethernet LAN

Hardware Installation

Connecting to 10BaseT Twisted Pair
Networks

The Trumpcard Ethernet LAN can be connected to a 10BaseT Network in
one of two ways: directly connected through a cable attached to the
Trumpcard if you have the 10BaseT version, or via the Media Access
Module if you need to connect with 10Base2 cabling.

Connecting directly to the Trumpcard, the cable supplied has a male RJ-45
connector at one end that can be attached to an input port of a 10BaseT
compatible concentrator; the external Media Access Module is not
required. All the necessary interface is provided within the Trumpcard.

To direct connect the Trumpcard to a 10BaseT Network connection follow
these steps:

• Locate the twisted pair cable that has a male RJ-45 connector at one

end and a PCMCIA Ethernet Adapter connector at the other.

• For a multi-function Trumpcard, the Ethernet connection is identified

on the back of the PC Card. Insert the PCMCIA Ethernet Adapter
connector into the one marked Ethernet.

• Connect the male RJ-45 connector into an input port of a 10BaseT

compatible concentrator.

Direct 10BaseT Ethernet Connection

User’s Guide and Reference 2 - 3

Section Two

The second method of connecting to a 10BaseT Network is via the Media
Access Module. A female RJ-45 connector is provided on the Media
Access Module for 10BaseT Network connections.

To connect the Trumpcard to a 10BaseT Network connection using the
Media Access Module, follow these steps:

• For a multi-function Trumpcard, the Ethernet connection is
identified on the back of the PC Card. Insert the PCMCIA Ethernet
Adapter connector on the Media Access Module into the one
marked Ethernet.

• Plug the male RJ-45 connector from the Network access cable into
the female RJ-45 connector on the Media Access Module.

Note: The Trumpcard is keyed to go in one way only. If you feel resistance

before it is fully inserted, remove it, turn it over, and re-insert it.

Media Access Module 10BaseT Network Connection

2 - 4 Trumpcard Ethernet LAN

Hardware Installation

Interface Cabling and Pinout

The direct connect 10BaseT cable provided with the Trumpcard is wired
for direct connection to an Ethernet 10BaseT Concentrator. If the premises
wiring scheme you are using does not match this wiring scheme, then
contact Ositech for assistance on how to make a 10BaseT Network
connection in your environment.

Lead Signal
1 TX+

2 TX­3 RX+
4nc
5nc
6 RX­7nc
8nc

10BaseT Pinout

User’s Guide and Reference 2 - 5

Section Two

Concentrators

The Trumpcard, when used with 10BaseT Twisted-pair cable, must always
connect to a concentrator. This results in a star-wired Network with the
concentrator at the centre of the star. The Trumpcard is compatible with
10BaseT concentrators from a variety of vendors.

Twisted Pair Network Characteristics

Standard IEEE 802.3 10BaseT
Data Rate 10 Mbits per second
Maximum length of connecting 100m (328')

nodes per network
Maximum number of computer 1024

nodes per network
Twisted-pair cable Category 3 (10 mbps) or

Category 4 (16 mbps) or
Category 5 (100 mbps)
that meet the requirements
of EIA/TIA-568 and EIA/TIA
TSB-36.

2 - 6 Trumpcard Ethernet LAN

Hardware Installation

Connecting to 10Base2 Thin Ethernet
Networks

The Trumpcard can only be connected to a 10Base2 Network by using the
Media Access Module.

The following items are required to interconnect the Trumpcard to a
10Base2 thin coax Ethernet Network:

• A BNC coaxial T-connector.

• Coaxial cable(s) and a 50 ohm cable terminator if required.

To connect the Trumpcard to a 10Base2 Network connection using the
Media Access Module, follow these steps:

• For the multi-function Trumpcard, the Ethernet connection is
identified on the back of the PC Card; insert the PCMCIA Ethernet
Adapter connector on the Media Access Module into the one
marked Ethernet.

• Attach the T-connector to the BNC connector on the Media Access
Module, align the notches in the T-connector with the posts on the
BNC connector, push the connector in, and twist about one-quarter
turn (until it is seated properly).

• Connect the coaxial cable(s) to the open ends of the T-connector to
form a single Network segment. If at the end of the network
segment, attach a 50 ohm cable terminator to the unused
T-connector post.

Note: The Trumpcard is keyed to go in one way only. If you feel resistance

before the it is fully inserted, remove it, turn it over, and re-insert it.

User’s Guide and Reference 2 - 7

Section Two

Media Access Module 10Base2 Network Connection

Thin Coax Ethernet Segment

A thin coax Ethernet cable segment is the length of cable between
terminations. The Trumpcard PC Card functions with 185 meter (607 foot
with IEEE 10Base2) or 300 meter (984 foot, using the extended length
option) cable segments. The two above mentioned types of thin coax
Ethernet cabling (IEEE 10Base2 and extended length option) are
commonly used. Pick one type of cabling and consistently obey the
protocol for that type throughout your network. If you mix the rules (for
example, using two repeater links permitted by 10Base2 with the 100
nodes per segment permitted under the extended length option), your
network may have an excessive number of errors or may not operate at all.

If your network uses standard 185-meter cable segments, all thin Ethernet
cable segments in the network can be up to 185 meters long. Five
standard length cable segments may be connected in line using
commercially available repeaters. The total network span with five
standard length segments is 925 meters (3,035 feet). No more than four
repeaters can be on the signal path from one node to any other node. The
standard 185 meter segment length is recommended because it allows
you to use common thin coax Ethernet components which conform to the
IEEE standard.

If your network is using extended length 300-meter cable segments , all
thin coax Ethernet cable segments in the network can be a maximum of
300 meters long. Three 300-meter cable segments may be connected in
line using repeaters. The total network span with three extended length
segments is 900 meters (2,953 feet). No more than two repeaters can be
in the signal path from one node to any other node.

2 - 8 Trumpcard Ethernet LAN

Hardware Installation

If you are using extended length segments, all repeaters and transceivers
must be designed for 300-meter operation. In addition, all LAN adapters
must be configured to operate with the extended segment length.

Note: You cannot use Ethernet adapters to extend 185-meter segments to

300-meter segments unless all LAN adapters and repeaters in the
network are capable of operation on the extended segment length.

User’s Guide and Reference 2 - 9