OSEE MVM-170, MVM-200 User Manual

MVM-170 MVM-200 Series

Quad Split LCD Monitor

User Manual

Product Information

Model:

MVM-170 MVM-200 Series Quad Split LCD Monitor

Version:

V010100

Release Date:

September 27th, 2016

Company

OSEE TECHNOLOGY CO., LTD.

Contact Information

Address:

No.22 Building, No.68 zone, Beiqing Road, Haidian District,
Beijing, China

Post Code:

100094

Tel:

([phone]

Fax:

([phone]

Web:

http://www.osee-dig.com/

E-mail:

[email protected]

About this manual

Important

The following symbols are used in this manual:



The further information or know-how for described subjects above which

helps user to understand them better.



The safety matters or operations that user must pay attention to when

using this product.

Contents

The user manual applies to the following device types:

 MVM-170-3HSV
 MVM-170-HSV
 MVM-170-SV
 MVM-200-3HSV
 MVM-200-HSV
 MVM-200-SV

The above listed devices have most similarities on appearance and
characteristics. The images of MVM-200-3HSV are adopted in the following
descriptions.
Any of the different specifications between the device types are elaborated.
Before reading the manual, please confirm the device type.

I

Contents

Contents .......................................................................................................... I



Chapter 1 Overview ....................................................................................... 1



Chapter 2 Safety ............................................................................................. 3



Chapter 3 Unpack and Installati on ............................................................... 7



Chapter 4 MVM-200 Features ...................................................................... 13



4.1

Front Panel Features ........................................................................ 16



4.1.1 Arrangement of Front Panel ........................................................... 16



4.1.2 Operation of Front Panel ................................................................ 17



4.1.3 Display Mode .................................................................................. 20



4.2

Rear Panel Features .......................................................................... 23



4.2.1 Arrangement of Rear Panel ............................................................ 23



4.2.2 Operations of Rear Panel ............................................................... 24



4.3

Supported Signal Format ................................................................. 26



Chapter 5 Functionality of the Main Menu ................................................. 29



5.1

Main Menu ......................................................................................... 30



5.1.1 STATUS Menu ............................................................................... 31



5.1.2 COLOR TEMP Menu ...................................................................... 32



5.1.3 MARKER Menu .............................................................................. 33



5.1.4 ALARM CONFIG Menu .................................................................. 36



5.1.5 AUDIO CONFIG Menu ................................................................... 37



5.1.6 USER CONFIG Menu ..................................................................... 39



5.1.7 OSD CONFIG Menu ....................................................................... 42



5.2

Menu Settings .................................................................................... 46



Chapter 6 Specifications ............................................................................. 49



Overview

1

Chapter 1 Overview

The MVM-170/MVM-200 series Quad Split LCD Monitor are high-performance
professional LCD monitor featuring quad split display. It supports high quality
quad split displays and is designed to tailor the extensive needs for
programming, concentrated on download and upload, broadcast master
control, studio, centralized monitoring and so on.
The MVM-170/MVM-200 series Quad Split LCD Monitor supports the
advanced 10- bit digital processing technology and also supports 3D comb
filter and de-interlace, accurate scaling engine, GAMMA and color temperature
adjustment function, in order to achieve the best possible image display. Each
display screen of the monitor is an independent professional monitor. So it can
achieve the various professional parameters and can be adjusted
independently, including GAMMA, color temperature, brightness, and so on.
The MVM-170/MVM-200 series Quad Split LCD Monitor supports 4ch
3G/HD/SD-SDI/CVBS signal and 1-way HDMI / DIV-D signal input. It can
simultaneously display four signal inputs, with three typical display modes
(including one full screen display, one - big with three - small screen display
and four uniform size screen display). Each display screen can achieve
professional monitor display functions, including embedded audio solution,
audio monitoring, audio meter display, TC code display, IMD, various Markers
and so on.

Figure 1 A Diagram of MVM-200 Monitor

Features

Overview

2



178-degree viewing angle



Multi-format analog and digital audio signals



Support select 4 from 5 input signals to display



Support a single screen display as a professional monitor



Support the independent adjustment of the parameters for single

screen



With all the important functions of multi-view processor



Support high-quality waveform, vector monitoring



Support HDMI output or HD-SD display, can achieve the cascade and

copy output of devices

Functionality



Supports MARKER, Time Code, MET display



Supports presetting the color temperature using customized values

Safety

3

Chapter 2 Safety

FCC Caution:

Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Safety

4

Warnings:

Read, keep and follow all of these instructions for your safety. Heed all
warnings.

Device

 Install in accordance with the manufacturer's instructions.

 Do not beat with a hard object or scratch the LCD display.

 Do not make the freeze picture displaying on the screen time too long,

otherwise, it will leave the afterimage on the screen.

 If the brightness is adjusted to the minimum, then it might be hard to

see the display screen.

 Refer all servicing to qualified service personnel. Servicing will be

required under all of the following conditions:



The unit has been exposed to rain or moisture.



Liquid had been spilled or objects have fallen onto the unit.



The unit has been damaged in any way, such as when the

power-supply cord or plug is damaged.



The unit does not operate normally.

 Clean only with dry cloth.

 Specifications are subject to change without notice.

Position

 Do not block any ventilation openings.

 Do not use this unit near water.

 Do not expose the unit to rain or moisture.

 Do not use this unit near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that product

Safety

5

heat.

 Do not place objects filled with liquids, such as vases, cups, etc. on or

over the device.

 A nameplate indicating operating voltage, etc., is located on the rear

panel.

 The socket-outlet shall be installed near the equipment and shall be

easily accessible.

Power Supply Cord

 Do not defeat the safety purpose of the polarized or grounding-type

plug.

 Do not damage the power cord, place the heavy objects on the power

cord, stretch the power cord, or bend the power cord.

 Protect the power cord from being walked on or pinched, particularly at

plugs, convenience receptacles, and the point where they exit from the
unit.

 If the power cord is damaged, turn off the power immediately. It is

dangerous to use the unit with a damaged power cord. It may cause
fire or electric shock.

 Unplug this unit during lighting storms or when unused for long periods

of time.

 Disconnect the power cord from the AC outlet by grasping the plug, not

by pulling the cord.

 Should any solid object or liquid fall into the cabinet, unplug the unit

and have it checked by qualified personnel before operating it any
further.

6

Unpack and Installation

7

Chapter 3 Unpack and Installation

Unpack:

When unpacking the components of MVM-200 monitor, please verify that none
of the components listed in Table 3.1 are damaged or lack. If there is any
missing, contact your distributors or OSEE for it.

Table 3-1 Packing List

NO. Detail list Quantity

1 Monitor 1

2 Optional Accessory

Monitor Stand 1

Rackmount Bracket 1

Wallmount Bracket 1

Extra control buttons bar 1

3 Accessory

Warranty card 1

Certificate card 1

User manual 1

4 The electric accessory

19V adapter 1

Power cord 1

Installation:

1.

Prepare for installation

Please follow the procedures below before installing MVM-200:

 Check the equipment for any invisible damage that may have occurred

during transit.

 Confirm all the items listed on the packing list have been received.

 Remove all the packing material including electrostatic-resistant

packing.

 Retain these packing materials for future use.

2.

Mount a MVM-200 in your desired location of a standard rack.
Adequate ventilation is required when installed to prevent possible
damage to the MVM-200.

3.

Connect required cables for signal input and output. For BNC
connections use 75Ω rated connectors.

Unpack and Installation

8

4.

Connect DC18~20V power source using the included power cord.

5. Connect the power cord to the power interface.

6. Fasten the power protect accessory.

7. As a final step, turn on the device by pressing the corresponding

power switch located on the front panel.



The pedestal and the monitor are packaged separately.



Connect a standard signal line to the corresponding input port. All BNC

connector impedance must be 75Ω.



Please use the power cord supplied to avoid unnecessary trouble, and

make sure be well grounded.



The factory default value for IP address is 192.168.1.86.

Installation Methods:

The MVM-200 monitor could be mounted to a monitor stand or mounted to a
cabinet or onto a wall. The MVM-170 monitor could be mounted to a monitor
stand or mounted to a cabinet.



Monitor Stand Installation

Unpack and Installation

9

Figure 3-1 Monitor Stand Installation



Cabinet Installation

The MVM-200 series monitors support cabinet installation. Firstly,
mount the rackmount brackets to the rear panel of the monitor, fasten
them, then mount the monitor onto the cabinet steadily and firmly.
Buckle the monitor with the hanger at the right top of the monitor on the
rear panel to lock the monitor in case of unexpected rollover.

Figure 3-2 Rackmount Installation



Hanger usage

Rotate the hanger to hook with the locating guide post to lock the
monitor, in case of unexpected rollover.

Unpack and Installation

10

Figure 3-3 Hanger Usage



Videowall Installation

The MVM-200 series monitors support compact installation for videowall.
Firstly, mount the wallmount brackets to the rear panel of the monitor,
fasten them, then, mount the monitor onto the videowall frame steadily
and firmly. Buckle the monitor with the hanger at the right top of the
monitor on the rear panel to lock the monitor in case of unexpected
rollover.

Figure 3-4 Wallmount Installation

Installation for the extra control buttons bar:

You can use the control buttons on the top of the monitor, or you can
amount an extra control buttons bar at the bottom of the monitor. The

Unpack and Installation

11

installation steps of the extra control buttons bar are as follows:

Step 1

: first, insert the FPC line of the monitor to the corresponding slot of

the extra control buttons bar, as shown in the following illustration:

Figure 3-5 FPC Connection

Step 2

: second, mount the extra control buttons bar with the kits at both

sides, fasten them firmly, as shown in the following illustration:

Unpack and Installation

12

Figure 3-6 Mount the Kit of the Extra Control Buttons Bar

Step 3

: at last, connect the extra control buttons bar to the monitor with
the pan head screws, fasten them firmly, as shown in the following
illustration:

Figure 3-7 Mount the Extra Control Buttons Bar

MVM Monitor Features

13

Chapter 4 MVM Monitor Features

This chapter describes the features of MVM-200 monitor. The features of
MVM-200 monitor are as shown in Figure 4-1 after installed and powered on:

Figure 4-1 Features of MVM-200 Monitor

1. Status Information

It is displayed in the top left corner of each display window on the
screen, and includes the input channel and signal format.

2. Audio Meter

It is displayed for audio monitoring. You can set its parameters in

AUDIO CONFIG menu. It could be semi-transparent displayed which

will reduce the impact for the image.

3. Waveform and Vector

This is effective only for SDI signal. The waveform and vector of the
input signal are configurable in the OSD CONFIG Menu.

4. Area Marker/Safe Marker/Center Marker

It is used to mark different area or position of the image, and there are
various marker, including Area Marker, Safe Marker, Center Marker.
You can set whether to display it or not and their displaying mode in

MARKER menu.

MVM Monitor Features

14

5.

Timecode

It is displayed at the bottom of the image, the format is HH:MM:SS:FF,

if there is no timecode available, the monitor will display --:--:--:--. You

can set its parameters in OSD CONFIG menu.

6. OSD TALLY

It is displayed OSD TALLY rectangle at the both sides of IMD bar, in

the bottom of each display window, and the color could be changed
according to the designated color (red, green, yellow, white). You can

set its parameters in OSD CONFIG menu.

7. IMD

The IMD text displays at the bottom of the screen, the length can’t
exceed 16 characters, and you can choose letter, number or other

character for it. You can set its parameters in OSD CONFIG menu.

There are several display modes for MVM-200 display: Single-screen,
Four equal screens, and One-big and with Three-small Screen.

Figure 4-2 Single-screen, full 16-channel audio meter

MVM Monitor Features

15

Figure 4-3 Four-screen, full 16-channel audio meter

Figure 4-4 One-big and With Three-small Screen, Full 16-channel

Audio Meter

Waveform and vector display: It displays only for CH1 and CH3 in the screen.
Each channel is corresponding to a display window. You can see the
Waveform and vector of CH1 is displayed in No.2 Window, and the Waveform
and vector of CH3 is displayed in No.4 Window.

Figure 4-5 Waveform and Vector Display



The

Status Information

displays at the top left corner of the each window,

it usually displays as the following situations:

MVM Monitor Features

16



"UNKNOW” appears if an unsupported signal is input.



“NO SIGNAL” appears if no signal is input.



The signal is normal, for example: 1080i59.94, NTSC, 1280X1024,

etc.

4.1 Front Panel Features

It will introduce the arrangement and the operations of the buttons in front of
the panel in the following.

4.1.1 Arrangement of Front Panel

There are a series of buttons at the bottom of the screen, and these
buttons are used to control the screen menu items.

123456 78910 11

12

Figure 4.1-1 the Buttons in Front Panel

As shown in Figure 4.1-1, these buttons are as follows:

1. CH1

2. CH2

3. CH3

4. CH4

MVM Monitor Features

17

5.

QUAD

6. DVI

7. MENU

8. F1/DOWN

9. F2/UP

10. ENTER

11. POWER

12. POWER indicator



The functionality of the control buttons on the top of the monitor is as the

same as the extra control buttons.

4.1.2 Operation of Front Panel

The functionality and usage of the buttons are as follows:

1. CH1

It is used to switch to the full screen of CH1, or select the signal from IN1
input interface.



Operation



Full screen of CH1: Press this button to switch from quad split

screen display to

CH1

full screen display.



Select CH1: when in quad split screen display mode, press

MENU

button to display the main menu in the center of the screen, then
press

CH1

button to switch to the

IN1

signal, and it will show the
CH1 information in the menu list. The current selected window will
be highlighted at the outline of the display window.

2. CH2

It is used to switch to the full screen of CH2, or select the signal from IN2
input interface. The operation is as the same as CH1's.

3. CH3

It is used to switch to the full screen of CH3, or select the signal from IN3
input interface. The operation is as the same as CH1's.

4. CH4

MVM Monitor Features

18

It is used to switch to the full screen of CH4, or select the signal from IN4
input interface. The operation is as the same as CH1's.

5. QUAD

This button is used to switch to display quad split windows, including four
uniform size screens display, one big with three small screens display.
Refer to “4.1.3 Display Mode” for details.

6. DVI

This button is used to switch the signal source for CH1 between HDMI
and IN1.

7. MENU

It is used to activate the Main menu. Press this button to do some
operations with the Main menu, it includes the following operations:



Display the Main menu



Back to the higher level menu



Quit the Main menu

Refer to “5.2 Menu Settings” for detail about the main menu operations.



After you have loaded the function menu list, it will be closed automatically

if you do nothing operation with it in 5s.



If the value related to the function button can’t be modified, the value

shows in highlight yellow.

8. F1/DOWN

This button is used to be a function button or an adjustable button. The
function can be set via the USER CONFIG menu.



Function button:

Press F1 to display the function menu list at the left
bottom corner of the screen. Toggle F1 button to change the value
related to this function



Adjustable button

: It is

DOWN(▼)

button when working with

MENU

.

Toggle this button to select the next item or decrease the number.



Use

FUNCTION KEY

menu to assign F1, F2. You can assign the function

from among: H/V DELAY, ASPECT, SCAN, MONO, BLUE ONLY, NATIVE,

MVM Monitor Features

19

WAVEFORM, AUD METER, MARKER, NONE. Refer to "5.1.6 USER

CONFIG Menu" for the details.

9. F2/UP

This button is used to be a function button or an adjustable button. The
function can be set via the USER CONFIG menu.



Function button:

Press F2 to display the function menu list at the left
bottom corner of the screen. Toggle F2 button to change the value
related to this function



Adjustable button

: It is

UP(▲)

button when working with

MENU

.

Toggle this button to select the next item or decrease the number.

10. ENTER

This button can achieve the following two situations:



Work with the Main MENU

: when working with the Main menu,

ENTER button achieve the following functions:



Enter into the next level menu: press

ENTER

button, you will enter
into the menu item as this relationship: the Main menu list
sub-menu list sub-menu value list, the current editable object is
in yellow control icon;



Confirm the value selection: press

ENTER

button to confirm the

value selection.



Adjust Menu:

when not displaying the Main menu, press

ENTER

button to display the adjust menu list, as shown in Figure 4.1-2,
toggle among these menu items: VOLUME, BRIGHTNESS,
CONTRAST, CHROMA.

BRIGHTNESS 50

Figure 4.1-2 Adjust Menu List

After displaying the Adjust menu, press UP or

DOWN

button to adjust

the menu value, and then press

ENTER

button to confirm the value

selection.

The relationship of the menu items and their range is shown in Table

4.1-1:

Table 4.1-1 The Description of Adjust Menu Items

Adjust Menu Description Range Default

MVM Monitor Features

20

Adjust Menu Description Range Default

VOLUME Adjust the volume 0~30dB 15

BRIGHTNESS Adjust the image brightness 0~100 50

CONTRAST Adjust the image contrast 0~100 50

CHROMA Adjust the image monochroma 0~100 50



Set these parameter values in the following position: BRIGHTNESS,

CONTRAST, CHROMA.



In Adjust Menu List on screen when pressing Enter key.



In Adjust menu of network control page.



After you have loaded the adjust menu list, it will be closed automatically if

you do nothing operation with it in 5s.



The main menu, the adjust menu, the function menu and the input signal

selection list of a screen may not be shown all simultaneously.

11. Power

Used to power on or standby, and the light in the button will indicate the
status of the power. If the light is green, the monitor is powered on, if the
light is flashing, the monitor is standby.



When the device is standby, cut off the power and restart the device, the

status of the device will be normal but not standby.

4.1.3 Display Mode

This device provides several display modes: Single screen, QUAD split
screen.

1. SINGLE: full screen display mode

There is only one picture for one signal source on the whole screen in
SINGLE mode, as shown in Figure 4.1-3:

MVM Monitor Features

21

SINGLEMODE

CH1

Figure 4.1-3 SINGLE Mode



Switch to SINGLE MODE: Press

CH1, CH2, CH3 or CH4

to display

the corresponding input signal on the full screen.



Signal Source Selection: Press

CH2, CH3, CH4

button, it will display

the corresponding signal source to

IN2, IN3, IN4

. If press

CH1

button,

it will display to signal source

IN1

by default, then, press

DVI

button

to switch between

IN1

and

HDMI

(coming from HDMI IN interface).
That is, the HDMI input could only be displayed in CH1 or CH1’s full
screen.

2. QUAD: QUAD split display mode

The whole screen is divided into four windows in QUAD mode, there are
two kinds of layouts: four uniform size screens(LAYOUT1) and one big
with three small screens. The latter including one big left with three right
small(LAYOUT2), one big right with three left small(LAYOUT3), one big
top with three bottom small(LAYOUT4).

Press

QUAD

button to switch among these four modes cyclically in
sequence, and you can see a prompt at the left corner of the screen to
show the layout character.

Figure 4.1-4 LAYOUT1-Four Uniform Size Screens



One big with three small screens display: one big left with three right

small, one big right with three left small, one big top with three bottom
small, as shown in Figure 4.1-5, Figure 4.1-6, Figure 4.1-7:

MVM Monitor Features

22

Figure 4.1-5 LAYOUT2-One Big Left with Three Right Small

Figure 4.1-6 LAYOUT3-One Big Right with Three Left Small

Figure 4.1-7 LAYOUT4-One Big Top with Three Bottom Small

The relationship between the display window and signal source channel is
one to one correspondence, and the position of each split window in the
above display modes is settled.



The signal source of CH1 can only be IN1 or HDMI.

MVM Monitor Features

23

4.2 Rear Panel Features

It will introduce the arrangement and the operations of the interfaces in rear
of the panel in the following.

4.2.1 Arrangement of Rear Panel

Take MVM-200 for example, as shown in Figure 4.2-1, there are various
input and output interfaces at the rear panel of MVM-200 monitor.

Figure 4.2-1 The Rear Panel of MVM-200 Monitor

The interfaces numbered from 1 to 8 in red dotted rectangle are
described as follows:

1. Power Input

2. Power Switch

3. HDMI Input Interface

4. Video Input Interface: IN1, IN2, IN3, IN4

5. Video Output Interface: OUT1, OUT2, OUT3, OUT4

6. HDMI Output Interface

7. Ethernet

8. GPI

MVM Monitor Features

24

9.

RS485

10. Audio Input/Output Interface

11. Top Control Buttons

4.2.2 Operations of Rear Panel

The details of these interfaces at the rear panel are described as follows:

1. Power Input

It provides one power input interface, the specification is DC18~20V. If
the power indicator is in green, the monitor is powered on, and if the
power indicator is off, the monitor is powered off.



Only use the power cord specified by the manufacture for your safety！

2. Power Switch

It provides one power switch to switch on or switch off. As shown in
Figure 4.2-2, push the button to the direction “-” to switch on the power,
or push the button to the direction “” to switch off the power.

Figure 4.2-2 Power Switch

3. HDMI Input Interface

It provides one HDMI input interface, HDMI Type-A connector with a
fastener.

4. Video Input Interface (BNC)

It provides four video input interfaces, labeled as IN1, IN2, IN3, IN4.
These inputs are adaptable for CVBS, SD/HD/3G-SDI(with embedded
audio). The IN1 is multiplexed with HDMI input for CH1.

5. Video Output Interface (BNC)

It provides four video output interfaces, labeled as OUT1, OUT2,
OUT3, OUT4. Loop out, corresponding with IN1, IN2, IN3, IN4.

MVM Monitor Features

25

6.

HDMI Output Interface

It provides one HDMI output interface, HDMI Type-A connector with a
fastener. It outputs the content of the current display on screen, that is,
the screen could be a single image, or a group of four images.

7. Ethernet (RJ-45)

It provides one 10/100M Ethernet connector. It is used to connect with
a computer to modify the network settings.

8. GPI(DB9)

It is used to control Tally light.
The relationship of the pins of GPI interface and its channel value is
shown in Table 4.2-1.

Table 4.2-1 The Relationship of GPI Pins and Channel Values

Tally Light Color RED GREEN GND

IN1 Pin 1 Pin 6

Pin 5

IN2 Pin 2 Pin 7

IN3 Pin 3 Pin 8

IN 4 Pin 4 Pin 9

9. IN/ OUT RS485 Interface (RJ-45)

Support for dynamic IMD and updating the new firmware.
The Comparison of Pins and Input/output connectors for RS485 is
shown as in Table 4.2-2:

Table 4.2-2 Input/output connectors for RS485

PIN No. RS485 IN Terminal Signal RS485 OUT Terminal Signal

1,2 GND GND

3 Tx- Tx-

4 Rx+ Rx+

5 Rx- Rx-

6 Tx+ Tx+

7,8 NC NC

MVM Monitor Features

26

10.

Audio Input/Output interface

It provides four pairs of audio input interfaces, and one pair of audio
output interfaces, RCA connector.

Figure 4.2-3 Audio Input/Output interface

11. Top Control Buttons

It provides a bar of control buttons at the top of the monitor, the
sequence of these buttons from right to left are CH1, CH2, CH3, CH4,

QUAD, DVI, MENU, DOWN( ), UP( ), ENTER, facing at the rear

panel of the monitor. The functionality of these buttons is the same as
the extra control buttons, no more description here.

Figure 4.2-4 Top Control Buttons

4.3 Supported Signal Format

The supported signal format for this device is as shown in Table 4.3-1:

Table 4.3-1 Supported Signal Format

SDI Video HDMI DVI

NTSC YES

MVM Monitor Features

27

SDI Video HDMI DVI

PAL YES

SECAM YES

NTCS-4.43 YES

PAL-M YES

480I60 YES YES

576I50 YES YES

480P60 YES

576P50 YES

720P24 YES

720P25 YES

720P30 YES

720P50 YES YES

720P60 YES YES

1035I60 YES YES

1080I60 YES YES

1080I50 YES YES

1080P24 YES YES

1080P25 YES YES

1080P30 YES YES

1080P50 YES YES

1080P60 YES YES

1080SF24 YES

VGA YES

SVGA YES

XGA YES

SXGA YES

UXGA YES

WVGA YES

WXGA YES

28

Functionality of the Main Menu

29

Chapter 5 Functionality of the Main Menu

This chapter describes the structure and functionality of the main menu, and
introduces how to modify and customize the menu settings.
The main menu includes the following menu items, as shown in Figure5-1.

Figure 5-1 Main Menu

Icon Menu Item Pages Description

STATUS 1 Status information

COLOR
TEMP

1 Color temperature information

MARKER 1 Marker information

ALRAM
CONFIG

1 Alarm information

AUDIO
CONFIG

1 Audio information

USER
CONFIG

1 User config information

OSD
CONFIG

2 OSD information

Functionality of the Main Menu

30

5.1 Main Menu

Press the MENU button, the main menu is displayed at the center of the

screen, as shown in Figure 5.1-1:

Figure 5.1-1 the Structure of the Main Menu

The menu interface is divided into three parts:

1. Menu Name

It displays the menu name of the current selected menu in menu list.

2. Main Menu List

It contains the menu list. Press UP or DOWN button to select the

corresponding menu item.

3. Sub-menu list

It lists the sub-menus, press MENU, UP, DOWN, Enter button to select

the sub-menu item.

4. Sub-menu value list

It lists the sub-menus value of the current select sub-menu, press UP,
DOWN and Enter button to modify the value of the sub-menu. Refer to

“5.2 Menu Settings” for details.



There is a yellow control icon when you select the menu or its value.



The sub-menu item is selected when the control icon which is in yellow

Functionality of the Main Menu

31

highlight is at the back of the item name.



The sub-menu item value is editable when the control icon which is in

yellow highlight is at the back of the item value.

The following will introduce the contents and functionality of these sub-menu
items in sorts.

5.1.1 STATUS Menu

The STATUS menu items are used to describe the current status
information of the monitor, the menu items are as shown in Figure 5.1-2:

Figure 5.1-2 STATUS Menu

The relationship of Items, Default Value, Domain Range and Description
of the sub-item is shown in Table 5.1-1:

Table 5.1-1 The Description of STATUS Menu Items

Items Default Value Domain Range Description

CH 3

--

Show the Input
channel number.

COLOR
TEMP

D65 --

Show the color
temperature.

ASPECT
MODE

16:9 --

Show the screen
Aspect Ratio.

Functionality of the Main Menu

32

Items Default Value Domain Range Description

SCAN
MODE

NORMAL

--

Show the scan mode.

IP
ADDRESS

192.168.1.86

--

Show the IP address.

SUBNET
MASK

255.255.255.0 --

Show the subnet
mask.

SERIAL
NUMBER

MVM2002015010801 --

Show the serial
number.

MODEL 3G --

Show the production
model.



The sub-menu values in

STATUS

menu can’t be modified, they are

displayed the actual status of the monitor.

5.1.2 COLOR TEMP Menu

The COLOR TEMP menu items are used to adjust the color temperature
parameters and the color balance, the menu items are as shown in Figure

5.1-3:

Figure 5.1-3 COLOR TEMP Menu

The relationship of Items, Default Value, Domain Range and Description

Functionality of the Main Menu

33

of the sub-item is shown in Table 5.1-2:

Table 5.1-2 The Description of COLOR TEMP Menu Items

Items Default Value Domain Range Description

COLOR
TEMP

D65



USER: Customized

by user



D56：5600K



D65：6500K



D93：9300K

Set color temperature

RED GAIN 128 0~256 Adjust the Red Gain

GREEN GAIN 128 0~256 Adjust the Green Gain

BLUE GAIN 128 0~256 Adjust the Blue Gain

RED BIAS 32 0~64 Adjust the Red Offset

GREEN BIAS 32 0~64 Adjust the Green Offset

BLUE BIAS 32 0~64 Adjust the Blue Offset

RESET -- --

Reset the Gain and
Offset values to the
product originals



The items about RED/GREEN/BLUE GAIN and BIAS are available only in

USER mode. If the COLOR TEMP is set to

USER

with customized settings,

you can select the menu item

COLOR TEMP RESET

command to

restore product originals for Gains and Offsets, and press

ENTER

button to

confirm the reset operation.

5.1.3 MARKER Menu

The MARKER menu items are used to adjust the marker parameters, the
menu items are as shown in Figure 5.1-4:

Functionality of the Main Menu

34

Figure 5.1-4 MARKER Menu

The relationship of Items, Default Value, Domain Range and Description
of the sub-item is shown in Table 5.1-3:

Table 5.1-3 The Description of MARKER Menu Items

Items

Default
Value

Domain Range Description

MARKER OFF OFF/ON

Set whether to show all of
the markers.
It is the main switch for
area marker, center
marker and safety
marker.

AREA MARKER OFF



OFF: close area

marker



4:3



16:9



15:9



14:9



13:9



1.85:1



2.35:1

Select the area marker
aspect ratio according to
the display aspect ratio.

CENTER
MARKER

OFF OFF/ON

Set whether to show the
center marker

SAFETY
MARKER

OFF



OFF



80%

Set the safety area size
according to the aspect

Functionality of the Main Menu

35

Items

Default
Value

Domain Range Description



85%



88%



90%



93%



95%

ratio and scan mode.

MARKER
LEVEL

1



1: 50%



2: 75%



3: 100%

Set the luminance of
marker line, including
safety marker, center
marker, area marker and
cross hatch.

MARKER MAT OFF



OFF: Normal

background, use
line for area marker
edge only



HALF: 50%

Background
brightness



BLACK: all black

Set the transparency of
area marker mat.



Markers

Marker Illustration Description

CENTER
MARKER

This marker enables
easier checking the center
portion’s focus.

AREA MARKER

This marker displays two
lines to identify an area
with a specified ratio.

SAFETY
MARKER

This marker displays a
rectangle to identify the
safety area with a
specified percentage.



MARKER MAT

The marker mat marks the outside area of the marker display with the
appointed transparency.

For example, set ASPECT as 16:9, AREA MARKER as 4:3, and SAFETY
AREA as 95%, then, the comparison of the three MARKER MATs are as

Functionality of the Main Menu

36

shown in Figure 5.1-5:

MARKER MAT=HALF MARKER MAT=BLACK

Figure 5.1-5 MARKER MAT



All markers will be hidden in the following modes though the corresponding

marker is enabled (the value is not OFF): NATIVE.



The safety marker area will change with the area marker.

5.1.4 ALARM CONFIG Menu

The Alarm Config Menu items are used to adjust the parameters displayed
on the screen, the menu items are as shown in Figure 5.1-6:

Figure 5.1-6 Alarm Config Menu

The relationship of Items, Default Value, Domain Range and Description

Functionality of the Main Menu

37

of the sub-item is shown in Table 5.1-4:

Table 5.1-4 The Description of Alarm Config Menu Items

Items

Default
Value

Domain Range Description

ALARM
DISPLAY

OFF

<OFF>/<ON> Enable/disable alarm display.

VIDEO LOSS OFF

<OFF>/<ON>

Enable/disable video loss alarm.

EDH/CRC OFF

<OFF>/<ON> Enable/disable EDH/CRC alarm.

COLOR FIELD OFF

<OFF>/<ON>

Enable/disable color field alarm.

VIDEO FREEZE OFF <OFF>/<ON>

Enable/disable video freeze alarm.

VIDEO BLACK OFF

<OFF>/<ON> Enable/disable video black alarm.

COLOR BAR OFF <OFF>/<ON>

Enable/disable color bar alarm.

AUDIO LOSS OFF

<OFF>/<ON> Enable/disable audio loss alarm.

AUDIO OVER OFF <OFF>/<ON>

Enable/disable audio over alarm.

AUDIO UNDER OFF

<OFF>/<ON> Enable/disable audio under alarm.

5.1.5 AUDIO CONFIG Menu

The AUDIO CONFIG menu items are used to adjust the audio parameters,
the menu items are as shown in Figure 5.1-7:

Figure 5.1-7 AUDIO CONFIG Menu

Functionality of the Main Menu

38

The relationship of Items, Default Value, Domain Range and Description
of the sub-item is shown in Table 5.1-5:

Table 5.1-5 The Description of AUDIO Menu Items

Items

Default
Value

Domain Range Description

AUDIO
SRC

OFF

EBD: embedded signal
EXT: external signal
OFF: no signal

Select external audio
source.

SPEAKER
L

EBD CH1

When the audio source is
EBD, the range of this item
is EBD CH1~ EBD CH16.

Select the embedded
audio channel to the left
speaker and line out.

SPEAKER
R

EBD CH2

When the audio source is
EBD, the range of this item
is EBD CH1~ EBD CH16.

Select the embedded
audio channel to the
right speaker and line
out.

METER DIS OFF

OFF/2CH/4CH/6CH/8CH/
10CH/12CH/14CH/16CH

Set whether to show
audio meter, and select
a meter display mode.
each CH* means the
amount of the channels
to be displayed.

ACTIVE
ONLY

OFF OFF/ON

Display the active
embedded audio group
only

REF LEVEL -20dB -20dB/-18dB

Select the reference
level

OVER
LEVEL

-10dB

-10dB

-8dB

-6dB

-4dB

-2dB

Select the overload level

The appearance of Meter is as shown in Figure 5.1-8:

Functionality of the Main Menu

39

Figure 5.1-8 Audio Meter



The prerequisite for the available settings of the display mode and the

position of audio meter is that the

METER DIS

is not OFF.



The SDI embedded audio outputs are selected by these items, the HDMI

outputs and analog audio outputs are fixed.

5.1.6 USER CONFIG Menu

The USER CONFIG menu items are used to adjust the parameters
defined by customers, the menu items are as shown in Figure 5.1-9:

Figure 5.1-9 USER CONFIG Menu

Functionality of the Main Menu

40

The relationship of Items, Default Value, Domain Range and Description
of the sub-item is shown in Table 5.1-6:

Table 5.1-6 The Description of USER CONFIG Menu Items

Items

Default
Value

Domain Range Description

BACK LIGHT 15 0~30 Adjust the back light

LANGUAGE ENGLISH ENGLISH/CHINESE

Select a language
mode

PHASE
(NTSC only)

50 0~100 Set the phase

APPERTURE 8 0~100

Set the picture
sharpness

F1 BUTTON MARKER

H/V DELAY, ASPECT,
SCAN, MONO, BLUE
ONLY, NATIVE,
WAVEFORM, AUD
METER, MARKER, NONE

Set a function to F1
button

F2 BUTTON SCAN

MARKER, AUD METER,
WAVEFORM, H/V DELAY,
NATIVE , BLUE ONLY,
MONO, ASPECT, SCAN,
NONE

Set a function to F2
button

LAYOUT2
MODE

16:9 16:9/4:3

Set the aspect ratio for
LAYOUT2(one big left
with three right small)

LOCK
NUMBER

-- --

Function lock code
input, 8 characters.
Each character can
input number or letter.
Note: Be careful to
adjust this option to
avoid unnecessary
mistakes.

VIDEO
FORMAT

720P 720P/1080I/1080P

Set the video output
format.

REFRESH
RATE

50 50/60

Set the video refresh
rate.



The length of LOCK NUMBER is up to 8 characters, you can use the

Functionality of the Main Menu

41

combination of these characters: number (0 to 9) and letter (A to Z). Press

ENTER

to edit the LOCK NUMBER, than use UP or

DOWN

to select

characters, than press

ENTER

to go to next character, press

MENU

to exit

editor.

1. SCAN

This product supports the following scan modes:

NORMAL OVER UNDER
Set the function button as [SCAN], press the button continuously to
activate various scan modes.



OVER: Zooms in/out of the image to 96% of its original size

without changing the aspect ratio.



NORMAL: Zooms in/out of the image without changing the aspect

ratio.



UNDER: Zooms in/out of the image without changing the aspect

ratio. Also, displays the data at the top of the horizontal blanking
block.

2. ASPECT

Set the aspect ratio of the screen.

3. BLUE ONLY

It is to activate BLUE ONLY mode that will remove red and green from the
input signal and display the screen only under a blue signal.

4. MONO

It is to activate MONO mode that will display the screen in monochrome
presentation, inactivate this mode to display the screen in color mode.



Press F1/F2 button to activate the assigned function and adjust the

parameter value.



The

SCAN

mode or the ASPECT mode is not selectable when Native mode

is set to ON.

Functionality of the Main Menu

42

5.1.7 OSD CONFIG Menu

The OSD CONFIG menu items are used to adjust the parameters defined
for IMD display and other OSD parameters, there are two pages of
parameters for this menu, select

NEXT PAGE

item at the first line of the

parameter list and press

Enter

button to turn page, the menu items are as

shown in Figure 5.1-10 and Figure 5.1-11:

Figure 5.1-10 OSD Menu-Page1

Figure 5.1-11 OSD Menu-Page2

The relationship of Items, Default Value, Domain Range and Description

Functionality of the Main Menu

43

of the sub-item is shown in Table 5.1-7:

Table 5.1-7 The Description of IMD Menu Items

Items

Default
Value

Domain Range Description

IMD DISPLAY ON OFF/ON

Set whether to display
IMD CHARACTER on
screen.

IMD COLOR RED

RED/GREEN/YELLOW/
WHITE

Set the color for IMD
CHARACTER.

IMD CHAR XXXXXXXX --

Set the IMD string
displayed on the
screen. After entering
this item, press Up or
Down to choose your
character for this IMD
string.

TC DISPLAY OFF

OFF/LTC/VITC

Set whether to display
TC, and select a mode
for TC display.

CH*WAVE
FORM

OFF

OFF/VECT100/VECT75/
WAVE FORM

Set the display mode of
wave form.

CH*WAVE
OVER LEVEL

100

0~100

Select the overload
level for WAVE FORM.

CH*WAVE
UNDER LEVEL

0 0~100

Select the under level
for WAVE FORM.

FORMAT
DISPLAY

AUTO



OFF: the display is

hidden



AUTO: the input

source and format
are displayed for
about 10 seconds
when the input of the
signal changes



ON: the input source

and format are
always displayed

Set whether to display
status information.
If the signal input is not
equal to "No signal" and
this item is auto, the
status information will
show 10 seconds when
the status changed, and
then closed
automatically.

CC ON OFF/ON

Set whether to display
caption
information.(Reserved)

IMD
PROTOCAL

LOCAL



LOCAL: Use IMD

setting to control.

Select an IMD protocol

Functionality of the Main Menu

44

Items

Default
Value

Domain Range Description



TSL3.1: Use the

TSLV3.1 protocol
setting to control.



TSL4.0: Use the

TSLV4.0 protocol
setting to control.



IMAGE VIDEO: Use

the Image video
protocol setting to
control.



UDP: Use the UDP

protocol setting to
control.

IMD ID 0 0~255

Set the ID number for
each monitor

IMD NAME XXXXXXXX

Set an IMD name for
each screen.

BAUD RATE 38400 9600/19200/38400

Select a baud rate for
communication. TSL
V3.1 and TSL V4.0 is
38400, Image video is
one of the
9600/19200/38400.

OSD TLY
MODE

RG



RG: Red/Green



GR: Green only



RGY:

Red/Green/Yellow



OFF: No tally light

Select the OSD Tally
mode. Only the TALLY
SOURCE is
STANDARD or
STANDARD + IV422,
the setting is available.

IMD TLY MODE T1

T1/T2/T1T2/T2T1/T1-/
T2-/T1T2-/T2T1-

Select the IMD Tally
mode.
Use this setting when
using the Image Video
tally control, this setting
will determine the state
which is selected.

TLY SOURCE STANDARD



STANDARD: Use

the Standard setting
to control tally via
contact closure on
GPI tally.



IMAGE VIDEO 422:

Use the setting to

Select the source for
tally source

Functionality of the Main Menu

45

Items

Default
Value

Domain Range Description

control tally state via
422 ports, GPI
toggle is no
available.



TSL: Use the TSL

422 setting to
control OSD and
LED tally via the TSL
serial protocol.

Figure 5.1-12 Wave Form



If IMD DISPLAY item is ON, the IMD CHARACTER in the black bar will

display on the bottom of the corresponding window.



Only CH1 and CH3 have wave form and vector functions, and the wave

form and vector parameters settings for CH1 is set in the menu list of CH2,

and the settings for CH2 is set in the menu list of CH4. When the

CH*WAVE FORM is not OFF, the wave form or vector of CH1 is displayed

in the display window of CH2, and the wave form or vector of CH3 is

displayed in the display window of CH4, for example, as shown in Figure

5.1-12.



The length of IMD NAME and IMD CHARACTER is up to 16 characters.

Functionality of the Main Menu

46

The character range is from 0x00 to 0x7F of ASCII. Press

ENTER

to edit

the IMD characters, than use UP or

DOWN

to select characters, than press

ENTER

to go to next character, press

MENU

to exit editor.

5.2 Menu Settings

When checking or modifying the value of the menu item, cooperating with the

following buttons: MENU, UP, DOWN, ENTER.

1. Operations to the Main menu



Display the Main Menu

Press MENU button to enter into the main menu, it displays at the top

left corner of the screen.



Switch menu items

After displaying the main menu, press UP or DOWN button to choose a

menu item, the menu item selected is in yellow.



Back to the Main menu

After entering to a sub-menu item or a sub-menu item value, press

MENU button to back to the upper level menu area.



Close the Main menu

Press MENU button to close the Main menu when the control icon is in

the Main menu item.



After you have loaded the Main menu, it will be closed automatically if you

do nothing operation with it in 60s.

2. Operations to sub-menu item



Display the sub-menu item

After display the Main menu, press UP or DOWN button to select a

menu item, and the right part displays its sub-menu items according to
the current selected menu item.



Switch sub-menu items

After displaying the sub-menu items list, press ENTER button to enter

Functionality of the Main Menu

47

into the sub-menu items list, press UP or DOWN button to choose a

sub-menu item, a yellow rectangle is in front of the selected sub-menu
item.



Back to menu item

After entering to the sub-menu item value, press MENU button to back
to menu items, or after setting the sub-menu item value and press Enter

button to firm the modification, the control icon is back to the
corresponding sub-menu item.

3. Operations to sub-menu item value



Switch sub-menu item value

When the control icon is in sub-menu item value, press UP or DOWN

button to switch among its value list.



Confirm the modification to sub-menu item value

Press ENTER button to confirm the selection of a value, and the control

icon is back to the corresponding sub-menu item.



Abandon the modification to sub-menu item value

Press MENU button to give up the modification to sub-menu item value,

and the control icon is back to the corresponding sub-menu item.



The value in white color is modifiable, and the value in blue color is

unmodifiable.

4. Selecting the Menu Language

You can select one of languages (English or Chinese) for displaying the
menu. The default language for the menu is Chinese. The following will
teach you how to switch to ENGLISH.



Operation:

Step 1 Select USER CONFIG menu

Press MENU button to display the OSD menu, click DOWN button to
select USER CONFIG menu.

Step 2 Select the value of the Language item

Press ENTER button to get into the USER CONFIG menu items, and
click DOWN button to select the sub-item LANGUAGE, then, click
ENTER button to get into the sub-value list, the current control icon is in

Functionality of the Main Menu

48

Chinese.

Step 3 Confirm the modification of the value of sub-item

Click DOWN button to select the sub-item LANGUAGE to English,
press ENTER button to confirm the modification.

Step 4 Exit the main menu

Click MENU button to exit the main menu.

5. Network Control

MVM-200 supports network interface. Connect a computer with
MVM-200 through this interface to achieve the network control to
MVM-200.
This chapter will introduce how to set and check the parameters of
MVM-200 in Internet Explorer.
Use Internet Explorer to enter into a web control page. For example,
input http://192.168.1.138 in address bar, it will display the then, press
Enter key, the management interface of MVM-200 is displayed. Set the
parameters in this web page.



The network address of the computer which is connected with MVM-200

and the network address of MVM-200 must be in the same segment.

Specifications

49

Chapter 6 Specifications

1. Product detailed information

Specification

V

alues

Model MVM-170 MVM-200

Dimension 17.3” 19.5”

Dimension(WxHxD)

--- 454.6x266.8x44.2mm(Without accessory)

--- 483.6x266.8x44.2mm(With rackmount bracket)

---

454.6x310.3x44.2mm(With extra control
buttons bar)

421.8x308.1x160mm (With monitor
stand)

454.6x318.2x160mm(With extra control buttons
bar and monitor stand)

421.8x264.3x45.5mm(Without monitor
stand)

454.6x266.8x44.2mm(Without optional
accessories or with only wallmount bracket)

Pixel Pitch (WxH) 0.1989×0.1989mm 0.2259×0.21874mm

Aspect Ratio 16:9 16:9

Display Area (WxH)

381.89ⅹ214.81mm 433.73ⅹ236.24mm

Viewing Angle (HxV)

178°x178° 178°x178°

Color Depth 262K colors 16.7M colors (6bit + A-FRC)

Resolution

1920×1080 1920×1080

Contrast (Typ.) 700:1 1000:1

Luminance (cd/㎡)

300 250

Response Time (ms) 14 14

Backlight RGB LED WHITE LED

Backlight Life(Hrs) 15000 30000

Work Temperature

0°C~50°C

Power Supply DC18~20V

Power Consumption Approx. 50W Approx. 51W

Weight --- >7kg

Video Input Interface BNC(X4, CVBS,3G/HD/SD-SDI adaptable), HDMI(X1 HDMI/DVI-D adaptable)

Video Output Interface BNC(X4, CVBS, 3G/HD/SD-SD Ioop-out), HDMI(X1, HDMI/DVI combined)

Audio Input Interface 4 pairs of Analog Stereo, RCA(X8), SDI embedded audio

Audio Output Interface 1 pair of Analog Stereo, RCA(X2)

Control Interface

GPI(DB9)X1

RS485(cascade RJ45) X2

Ethernet(10/100M adaptive RJ45) X1

Signal Formats

CVBS: PAL, NTSC

SD-SDI: 480i60, 576i50

Specifications

50

Specification

V

alues

HD-SDI: 1080i50, 1080i 59.94, 1080i 60, 720p50, 720p 59.94, 720p 60, 1035i59.94, 1035i
60

3G-SDI: 1080p50, 1080p60

CVBS Input/Output

Signal Type NTSC, PAL

Signal Amplitude 1Vp-p+/-3dB

Impedance 75Ω

Return Loss >40 dB to 5 MHz

DC Offset 0V±0.05 V

Frequency Response ±0.2 dB to 5 MHz

Differential Gain <1%

Differential Phase <1.5°

3G-SDI /HD-SDI /SDI-SDI Input/Output

Signal Type SMPTE 424M, SMPTE 292M, SMPTE 259M, SMPTE 297M, SMPTE ST 2048-2

Connector BNC per IEC 169-8

Impedance 75Ω

Return Loss

>18 dB 5 to 270 MHz
>15 dB 270 MHz to 1.5 GHz
>10 dB up to 3 GHz

Maximum Signal Level 800 mV pk-pk 10%

Signal Amplitude 800 mV pk-pk 10%

DC Offset 0 V ±0.5 V

Overshoot <10%

Jitter <0.2 UI

Rise/Fall Time

<700 ps for SD
<270 ps for 1.5 Gb/s HD
<135 ps for 3 Gb/s HD

Extinction Ratio >8

Back Reflection <-14 dB

*The unit about the appearance attributes in above table is mm.

2. Input/Output Resolution, Frame Refresh Rate and Color Matrix

ASPECT
RATIO

OVERSCAN NATIVE

FULL
NORMAL

Frame
Rate

Color
Matrix

INPUT OUTPUT INPUT OUTPUT

INPUT
ALL

OUTPUT
NORMAL

NTSC

16:9

684X462

1920X1080

720X487 720X487 720X487

1920X1080

60 601

4:3 1440X1080 1440X1080

PAL

16:9

684X548

1920X1080

720X576 720X576 720X576

1920X1080

50 601

4:3 1440X1080 1440X1080

SECAM

16:9

684X548

1920X1080

720X576 720X576 720X576

1920X1080

50 601

4:3 1440X1080 1440X1080

Specifications

51

ASPECT
RATIO

OVERSCAN NATIVE

FULL
NORMAL

Frame
Rate

Color
Matrix

NTCS-4.43

16:9

684X462

1920X1080

720X487 720X487 720X487

1920X1080

60 601

4:3 1440X1080 1440X1080

PAL-M

16:9

684X462

1920X1080

720X487 720X487 720X487

1920X1080

60 601

4:3 1440X1080 1440X1080

480I60

16:9

684X462

1920X1080

720X487 720X487 720X487

1920X1080

60 601/709

4:3 1440X1080 1440X1080

576I50

16:9

684X548

1920X1080

720X576 720X576 720X576

1920X1080

50 601

4:3 1440X1080 1440X1080

480P60

16:9

684X462

1920X1080

720X487 720X487 720X487

1920X1080

60 601/709

4:3 1440X1080 1440X1080

576P50

16:9

684X548

1920X1080

720X576 720X576 720X576

1920X1080

50 601

4:3 1440X1080 1440X1080

720P24 16:9 1216X684 1920X1080

1280x72
0

1280x720 1280x720 1920X1080 48 709

720P25 16:9 1216X684 1920X1080

1280x72
0

1280x720 1280x720 1920X1080 50 709

720P30 16:9 1216X684 1920X1080

1280x72
0

1280x720 1280x720 1920X1080 30 709

720P50 16:9 1216X684 1920X1080

1280x72
0

1280x720 1280x720 1920X1080 50 709

720P60 16:9 1216X684 1920X1080

1280x72
0

1280x720 1280x720 1920X1080 60 709

1035I60 16:9 1824X984 1920X1080

1920X10
35

1920X1035 1920X103

5

1920X1080 60 709

1080I60 16:9

1824X102
6

1920X1080

1920X10
80

1920X1080 1920X108

0

1920X1080 60 709

1080I50 16:9

1824X102
6

1920X1080

1920X10
80

1920X1080 1920X108

0

1920X1080 50 709

1080P24 16:9

1824X102
6

1920X1080

1920X10
80

1920X1080 1920X108

0

1920X1080 48 709

1080P25 16:9

1824X102
6

1920X1080

1920X10
80

1920X1080 1920X108

0

1920X1080 50 709

1080P30 16:9

1824X102
6

1920X1080

1920X10
80

1920X1080 1920X108

0

1920X1080 60 709

1080P50 16:9

1824X102
6

1920X1080

1920X10
80

1920X1080 1920X108

0

1920X1080 50 709

1080P60 16:9

1824X102
6

1920X1080

1920X10
80

1920X1080 1920X108

0

1920X1080 60 709

1080SF24 16:9

1824X102
6

1920X1080

1920X10
80

1920X1080 1920X108

0

1920X1080 48 709

VGA 640X480 1920X1080 60-75

SVGA 800X600 1920X1080 60-75

XGA 1024x768 1920X1080 60-75

SXGA 1280x102 1920X1080 60-75

Specifications

52

ASPECT
RATIO

OVERSCAN NATIVE

FULL
NORMAL

Frame
Rate

Color
Matrix

4

UXGA

1600x120
0

1920X1080 60

WXGA 1360X768 1920X1080 60

WUXGA

1920x120
0

1920X1080 60

*Don’t display all OSD when SCAN is NATIVE.
*Don’t display MARKER when SCAN is NATIVE.

3. Dimensions

The description of the product dimensions is shown as in the following
figures(Unit: mm):



MVM-170

Figure 6-1 Front Panel(Unit: mm)

Specifications

53

Figure 6-2 Rear Panel(Unit: mm)

Figure 6-3 Side View(Unit: mm)

Figure 6-4 Top View(Unit: mm)

Specifications

54



MVM-200

Figure 6-5 Front Panel(Unit: mm)

Figure 6-6 Rear Panel(Unit: mm)

Specifications

55

Figure 6-7 Side View(Unit: mm)

Figure 6-8 Top View(Unit: mm)



MVM200 –With rackmount brackets

Figure 6-9 Front Panel(Unit: mm)

Specifications

56

Figure 6-10 Rear Panel(Unit: mm)

Figure 6-11 Side View(Unit: mm)

Figure 6-12 Top View(Unit: mm)

Specifications

57



MVM-200 –With monitor stand and extra control buttons bar

Figure 6-13 Front Panel(Unit: mm)

Figure 6-14 Rear Panel(Unit: mm)

Specifications

58

Figure 6-15 Side View(Unit: mm)

Figure 6-16 Top View(Unit: mm)



Specifications are subject to change without notice.

------------------No Text Below------------------

FOR MORE INFORMATION PLEASE VISIT: http://www.osee-dig.com/
OSEE TECHNOLOGY CO., LTD.
No.22 Building, No.68 zone, Beiqing Road, Haidian District, Beijing, China
Tel: [phone], Fax: [phone]
E-mail: [email protected]