Page 1
STEP 1
Trace along the inclusive template. Cut along the traced line using a
drywall saw or rotary drill. A simple, inexpensive drywall saw (about
$10 at your local hardware store) is the best choice for beginners.
Caution: This is the most important part of the entire installation.
If you are not certain whether any obstructions exist behind the
desired mounting area, you should start by cutting a small hole in
the center of your penciled mounting hole with a drywall saw. Use a
piece of sandpaper to sand down the cut out edge for a smoother
contour. (See Diagram 1 and Diagram 2)
OSD
AUDIO
Tools needed for installation
- Pencil
- Drill
- Tape Measure
- Wire cutter
- Philips-head screwdriver
- Sandpaper
Quick installation guide
- Where is the best place to install the speakers
- Where do the speakers sound the best
- Try to separate the speakers 6 - 10 feet apart.
- When placing the speakers in the ceiling, try to install them
so that the xed 15 angle woofer is pointed towards the main
listening area. (For LCR model only)
- If you intend to paint the grilles, try to do so before installation.
---------------
- Utility knife
- Safety eyewear
- Gloves
Diagram 1:
Cutout tracing
Owner’s Manual
In-Wall Speakers
Speaker wire
To determine the length and the gauge of speaker wire, you will need to
measure the distance between your receiver/amplifier and the speakers.
- Measure the distance from the receiver/amplifier to the speakers.
- Always buy more than you think you would need.
- Equal wire lengths should always be used to maintain an equal
balance in sound volume.
- Sound quality is lost when using thin wire gauge over a long
distance.
18AWG minimum - for distances up to ………………………. . 10 ft
16AWG - from ……………………………………………. 10 to 50 ft
14AWG - from …………………………………………… 50 to 100ft
STEP 3
Your in-wall speakers come from the factory with the tweeter facing
response. However, you can adjust the tweeter to focus the sound at
your listening location. In order to do this, gently press on the grill (See
Diagram 3). Caution: Do not touch the tweeter dome while adjusting for
your hearing preference. (See Diagram 3)
Diagram 3:
Adjust the tweeter here
Tweeter
- - - - - - - -
STEP 2
Run the cable into the cut out location while leaving an extra two
feet to make the connection to the speaker easier. Strip back
approximately ½” inch of the speaker cable insulation and twist
the copper wires tightly for easy insertion.
On the back of the speaker, press down on the gold-plated
compression terminal to reveal the "eye" and insert the speaker
cable through the eye for secure connection. Release the compression terminal to lock each cable securely.
- - - - - - - - - - -
-----------------
Diagram 2:
Cut Out
STEP 4
Tighten the dog-ear brackets by simply turning the screws on the
slowly clockwise. The quick-turn mounting system and frame will
"sandwich" or clamp around the wall to hold the speaker securely in
place. (See Diagram 4)
Diagram 4:
Mounting Dog Ear
Loose
..
......
.....
.
Closed
dog ear
.....
Loose
.
......
..
Closed
Page 2
STEP 5
TIP: Adjust the bass and the treble setting on your speakers by
shifting the knob either to the left or right. Speakers positioned
closer to a corner often produce more bass and will usually benefit
with the tweeter switch in the +3dB position. Speakers located
within a few feet of a listener's ear will often sound better with the
tweeter switch set to -3dB. Furthermore, rolled in insulation materials, such as a foam bedding would work as a dampening material
(Not applicable to certain models)
(See Diagram 5)
Diagram 7
LEFT OUT
+
-
Receiver/Amplifier
RIGHT OUT
+
-
Diagram 5
+3 0 -3
+
Treble Adjustment Switch
TIP: Blown-in insulation can sometimes work its way into the moving
components of the speaker, negatively impacting performance. It is
best to replace about a one square foot section directly behind the
speaker with rolled-in (bat) insulation. (See Diagram 6)
Note: The wire for both speakers should be about the same length.
the excess wire behind the wall
_
TREBLE
+3 0 -3
+
BASS
Bass Adjustment Switch
Adjustment Switches
_
Diagram 6
Terminal identification
Power handling
(10 watts)
LEFT
Note: Speaker terminals have corresponding (+) and (-) terminals. It is
important to connect both speakers in phase. Out of phase will result in
thin sound and weak bass.
Amplier/Receiver Considerations
wattage is comparable to the speaker’s power handling. Please refer to
your owner’s manual for reference.
When connecting any speakers to the amplier or receiver, always make
sure the power is o. Locate the connection terminals on the back of
your receiver or amplier. Always make sure to connect audio out from
the back of your receiver or amplier to the speakers. (See Diagram 7)
minimum
RIGHT
70 Volts Consideration ( Applicable to only 70V tap Speakers)
The 70V transformer offers you the ability to daisy chain multiple
number of speakers in series. In doing so, you would simply connect
1 pair of outputs to each speaker and daisy to subsequential
speaker/s. If you don’t intend to daisy chain the speakers, set the
default setting to 8 Ohm (See Diagram 8)
Diagram 8
-
5
w
w
5
.
-
2
-
Ω
8
1
0
w
Warranty & Repair
All OSD AUDIO speaker products have (10) year Limited Warranty against defects in materials and workmanship. Proof of purchase must accompany all claims.
During the warranty period OSD AUDIO will replace any defective part and correct any defect in workmanship without charge for either parts or labor
OSD AUDIO may replace returned speakers with a product of equal value and performance. In such cases, some modications to the mounting may be necessary and
For this warranty to apply, the unit must be installed and used according to its written instructions. If necessary, repairs must be performed by OSD AUDIO. The unit
must be returned to OSD AUDIO at the owner's expense and with prior written permission. Accidental damage and shipping damage are not considered defects, nor
is damaged resulting from abuse or from servicing performed by an agency or person not specically authorized in writing by OSD Audio
OSD AUDIO sells products only through authorized dealers and distributors to ensure that customers obtain proper support and service. Any OSD AUDIO product
purchased from an unauthorized dealer or other source, including retailers, mail over dealers and online sellers will not be honored or serviced under existing OSD
AUDIO warranty policy. Any sale of product by an unauthorized source or other manner not authorized by OSD AUDIO shall void the warranty on the applicable
Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases, repairs will be made on the basis of the retail
value of the parts and labor. To return for repairs, you must email customer service at RMA@OSDAUDIO.com for a Returned Merchandise Authorization (RMA) number# then
the unit must be shipped to OSD AUDIO at the owner's expense, along with a note explaining the nature of service required. Be sure to pack the speaker(s) in a corrugated
container with at least 3 inches of resilient material to protect the unit from damage in transit.
are not OSD AUDIO’s responsibility.
product.
Damage caused by abuse, accident, misuse, negligence, or improper operation (installation) • Any products that have been altered or modied • Any product whose
identifying number of decal, serial #, etc. has been altered, defaced or removed • Normal wear and maintenance.
This Warranty Does Not Cover:
Page 3
In Wall Model
MKW-850
IW-850
IW-840
CW - 840SQ
Speaker Type:
In Wall Speakers
Tweeter:
Woofer:
Impedance:
Sensitivity:
Contour Switches:
Frequency Response:
Power Handling:
Dimensions: (H x W x D)
Wall Cut Out: (H x W)
Unit of Measure: Pair Pair
IW-810
8” Custom Series
In Wall Speakers
1” Pivoting Silk Dome
8” Polypropylene
8 Ω
1” Pivoting Aluminum
Tweeter
8” Kevlar Cones
8 Ω
92dB 1w/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
25Hz - 22kHz
200 Watts
Pair
IW-800
8” Contractor Series
In Wall Speakers
1” Pivoting Silk Dome
8” Polypropylene
8 Ω
8” Kevlar In wall
Home Theater Speakers
1” Pivoting Aluminum
Tweeter
8” Kevlar Cones
8 Ω
92dB 1w/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
26Hz - 22kHz
175 Watts
IW-690
6 ½” Kevlar Inwall
Home Theater Speakers
1” Pivoting Aluminum
Tweeter
6 ½” Kevlar Cones
8 Ω
Pro Series In Wall Speakers
1” Pivoting Silk Dome
8” Polypropylene
8 Ω
90dB
2-Position Front-Mounted
±3dB Bass & Treble Switches
36Hz - 22kHz
175 Watts
13 ¾” x 10“ x 3 ¾”
12 ¾” x 8 ¾”
IW-680
Pro Series In Wall Speakers
1” Pivoting Aluminum
Tweeter
6 ½” Polypropylene
8 Ω
8” Squared Co-Axial
Speaker In Wall Speaker
1” Pivoting Silk Dome
8” Polypropylene
8 Ω
90dB
N/A
N/A
36Hz - 20kHz
150 Watts
10” x 10” x 3 ½”
Pair
IW-670
6 ½” Custom Series
In Wall Speakers
1” Pivoting Silk Dome
6 ½” Polypropylene
8 Ω
90dB
N/A
N/A
38Hz - 22kHz
150 Watts
12 ¾” x 8 ¾”
Pair
MKW-650
In Wall Speakers
1” Pivoting Aluminum
Tweeter
6 ½” Polypropylene
8 Ω
92dB
2-Position Front-Mounted
±3dB Bass & Treble Switches
28Hz - 22kHz
175 Watts
89dB
N/A
N/A
45Hz - 22kHz
120 watts
12 ¾” x 8 ¾”
Pair
CW - 640SQ
6 ½” Squared Co-Axial
Speaker In Wall Speaker
1” Pivoting Silk Dome
6 ½” Polypropylene
8 Ω
91dB
N/A
N/A
38Hz - 22kHz
150 Watts
92dB 1w/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
30Hz - 22kHz
150 watts
Pair Pair Pair
IW-620
6 ½” Contractor Series
In Wall Speakers
1/2 ” PEI Dome
6 ½” Polypropylene
8 Ω
88dB
N/A N/A
N/A
60Hz - 22kHz
100 Watts
90dB
N/A
N/A
38Hz - 22kHz
150 watts
CW - 540SQ
5 ¼” Squared Co-Axial
Speaker In Wall Speaker
5 ¼” Polypropylene
8 Ω
90dB
N/A
N/A
58Hz - 22kHz
125 Watts
87dB
N/A
N/A
48Hz - 22kHz
125 Watts
IW-540
Pro Series In Wall Speaker
1” Pivoting Silk Dome1” Pivoting Silk Dome
5 ¼” Polypropylene
8 Ω
90dB
N/A
58Hz - 22kHz
100 Watts
”
Pair
Pair
”
Pair
5 ¾” x 5 ¾”
Pair
Pair
Page 4
In Wall Model
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Contour Switches:
Frequency Response:
Power Handling:
Dimensions: (H x W x D)
Wall Cut Out: (H x W)
Unit of Measure:
In Wall Center LCR
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Contour Switches:
Frequency Response:
Power Handling:
Dimensions: (H x W x D)
Wall Cut Out: (H x W)
Unit of Measure:
IW-530
5 ¼” Custom Series
In Wall Speakers
1” Pivoting Silk Dome
5 ¼” Polypropylene
8
87dB
N/A
N/A
68Hz - 22kHz
100 Watts
Pair Pair
MK-IW550 LCR
5 ¼” MK Spitre Series
LCR In Wall Home Theater
Speaker
1” Pivoting Aluminum
Tweeter
Dual 5 ¼” Kevlar Cones
8
91dB 1w/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
29Hz - 22kHz
150 watts
6 ⁄” x 13 ⁄
Each
IW-520
5 ¼” Contractor Series
In Wall Speakers
1/2” PEI Dome
5 ¼” Polypropylene
8
88dB
N/A
N/A
75Hz - 22kHz
90 Watts
IW-550 LCR
5 ¼” Kevlar Center Channel
LCR In Wall Home Theater
Speaker
1” Pivoting Aluminum
Tweeter
Dual 5 ¼” Kevlar Cones
8
91dB 1w/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
30Hz - 22kHz
150 watts
Each
IW-545 LCR
Pro Series Center
In Wall LCR Speaker
1” Pivoting Silk Dome
Dual 5 ¼” Polypropylene
8
90dB
N/A
N/A
50Hz - 22kHz
125 Watts
Each
Silk
IW-525 LCR
5 ¼” Custom Series
Center Channel LCR
In Wall Speaker
1” Pivoting Silk Dome
Dual 5 ¼” Polypropylene
8
90dB
N/A
N/A
55Hz - 22kHz
100 Watts
Each
In Wall Subwoofer
Speaker Type:
Woofer:
Impedance:
Sensitivity:
Contour Switches:
Frequency Response:
Power Handling:
Mounting Depth:
Wall Cut Out: (H x W)
Unit of Measure: Each Each
IW-S10
10” In Wall Subwoofer
10“ Polyproplene
8
86dB
N/A
38Hz - 200Hz +/- 3dB
25-200 watts
3 ¾”
IW-S8
8” In Wall Subwoofer
8” Polypropylene
8
87dB
N/A
40Hz - 200Hz +/- 3dB
25-150 Watts
8 ¾” x 8 ¾”
Page 5
Architectural
Ceiling Element
ACE-950
ACE-850MK
ACE-800
ACE-750
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Contour Switches:
Frequency Response:
Power Handling:
Dimensions:(D x H)
Ceiling Cut Out:
Unit of Measure:
ACE-650MK
6 ½” Kevlar In Ceiling
Home Theater Speakers
1” Pivoting Aluminum
Tweeter
6 ½” Kevlar Cones
8
92dB 1W/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
28Hz - 22kHz
175 Watts
7 ⁄” x 4 ¼”
7 ⁄”
Pair
8 ½” Kevlar In Ceiling
Home Theater Speakers
1” Pivoting Aluminum
Tweeter
8 ½” Kevlar Cones
8
89dB
2-Position Front-Mounted
±3dB Bass & Treble Switches
25Hz - 22kHz
225 Watts
10 ¾” x 5”
9 ½”
Pair
ACE-645
6 ½” High Denition
Pro Series Ceiling Speakers
1” Pivoting Silk High
Teleron Dome
6 ½” Polypropylene
8
92dB 1W/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
36Hz - 22kHz
150 Watts
7 ⁄” x 4”
7 ⁄”
Pair
8” Kevlar In Ceiling
Home Theater Speakers
1” Pivoting Aluminum
Tweeter
8” Kevlar Cones
8
92dB
2-Position Front-Mounted
±3dB Bass & Treble Switches
25Hz - 22kHz
200 Watts
10 ¾” x 5”
9 ½”
Pair
ACE-640
6 ½” High Denition
Pro Series Ceiling Speakers
1” Pivoting Silk Dome
6 ½” Polypropylene
8
91dB
2-Position Front-Mounted
±3dB Bass & Treble Switches
38Hz - 22kHz
150 watts
7 ⁄” x 4”
Pair
8” Custome Series
Ceiling Speakers
½” PEI Dome
8” Polypropylene
8
90dB
2-Position Front-Mounted
±3dB Bass & Treble Switches
45Hz - 22kHz
120 Watts
10 ¾” x 3 ⁄”
9 ⁄”
Pair
ACE-600
6 ½” Custome Series
Ceiling Speakers
¾” Pivoting Silk Dome
6 ½” Polypropylene
8
89dB
2-Position Front-Mounted
±3dB Bass & Treble Switches
58Hz - 22kHz
125 Watts
7 ⁄” x 4”
7 ⁄”
Pair
7” Kevlar In Ceiling
Home Theater Speakers
1” Pivoting Aluminum
Tweeter
7 ” Kevlar Cones
8
88dB 1W/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
28Hz - 22kHz
200 Watts
9” x 3 ⁄”
9”
Pair
ACE-550MK
5 ¼” Kevlar In Ceiling
Home Theater Speakers
1” Pivoting Aluminum
Tweeter
5 ¼” Polypropylene
8
91dB
2-Position Front-Mounted
±3dB Bass & Treble Switches
50Hz - 22kHz
150 Watts
6 ⁄” x 3 ½”
6 ⁄”
Pair
ACE-540
5 ¼” Custome Series
Ceiling Speakers
¾” Silk Dome
5 ¼” Polypropylene
8
91dB
2-Position Front-Mounted
±3dB Bass & Treble Switches
65Hz - 20kHz
120 Watts
6 ⁄” x 3 ½”
6 ⁄”
Pair
ACE-520
5 ¼” Custome Series
Ceiling Speakers
½” PEI Dome
5 ¼” Polypropylene
8
91dB
2-Position Front-Mounted
±3dB Bass & Treble Switches
75Hz - 22kHz
100 Watts
6 ⁄” x 3 ½”
6 ⁄”
Pair
ACE-400
3” Architectural Ceiling
Speakers
N/A
3” Polypropylene
8
92dB 1W/1m
N/A
N/A
120Hz - 22kHz
60 Watts
4 ⁄” x 2 ½”
4 ½”
Pair
Architectural
In Wall Center LCR
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Contour Switches:
Frequency Response:
Power Handling:
Dimensions: (H x W x D)
Ceiling Cut Out:
Unit of Measure:
(H x W)
IW750LCR.
7” Kevlar In Ceiling
Home Theater Speakers
1” Pivoting Aluminum
Tweeter
Dual 7” Kevlar Cones
8
89dB
2-Position Front-Mounted
±3dB Bass & Treble Switches
28Hz - 22kHz
200 Watts
H 3 ½” x W 8 ½” x D 15 ⁄”
H 3 ½” x W 8 ½”
Each
Page 6
In-Ceiling Model
MK-850
ICE-850
ICE-870
MK-840
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Contour Switches:
Frequency Response:
Power Handling:
Dimensions:
Ceiling Cut Out:
Unit of Measure:
ICE-840
Pro Series Ceiling Speakers
1” Pivoting Silk Dome
8” Polypropylene
8
91dB
N/A
N/A
36Hz - 22kHz
175 Watts
(D x H)
Ceiling Speakers
1” Pivoting Aluminum
Tweeter
8” Kevlar Cones
8
92dB 1W/1m
2-Position Front-Moun
±3dB Bass & Treble Switches
25Hz - 22kHz
200 Watts
Pair
ICE-810
8” Custom Series
Ceiling Speakers
1” Pivoting Silk Dome
8” Polypropylene
8
89dB
N/A
N/A
38Hz - 22kHz
140 Watts
ted
8” Kevlar Ceiling Home
Theater Speakers
1” Pivoting Aluminum
Tweeter
8” Kevlar Cones
8
92dB
2-Position Front-Mounted
±3dB Bass & Treble Switches
26Hz - 22kHz
175 Watts
Pair
ICE-800ST
8” Ceiling Speaker
With Back Can
1” Pivoting Tweeter
8” Polypropylene
8 or 70v
89dB
N/A
N/A
45Hz - 20kHz
120 Watts
11” x 7”
8” Kevlar LCR Ceiling
Home Theater Speaker
1” Pivoting Aluminum
Tweeter
8” Kevlar Cone
8
92dB 1w/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
26Hz - 22kHz
175 Watts
Pair
ICE-800
8” Contractor Series
Ceiling Speakers
1/2 PEI Dome
8” Polypropylene
8
89dB
N/A
N/A
45Hz - 22kHz
120 Watts
Ceiling Speakers
1” Pivoting Titanium
Tweeter
8” Polypropylene
8
92dB 1W/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
32Hz - 22kHz
175 Watts
Pair
MK-650
Ceiling Speakers
1” Pivoting Aluminum
Tweeter
6 ½” Kevlar Cones
8
92dB 1W/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
28Hz - 22kHz
175 Watts
Pair
ICE-650
6 ½” Kevlar Ceiling
Home Theater Speakers
1” Pivoting Aluminum
Tweeter
6 ½” Kevlar Cones
8
92dB 1w/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
30Hz - 22kHz
150 watts
Pair Pair
Pair
ICE-670
6 ½” Kevlar LCR Ceiling
Home Theater Speaker
1” Pivoting Aluminum
Tweeter
6 ½” Kevlar Cone
8
92dB 1w/1m
N/A
N/A
30Hz - 22kHz
150 watts
8 ¼”
Each
Each
ICE-660
Pro LCR Ceiling Speaker
1” Pivoting Silk Dome
6 ½” Polypropylen
8
92dB 1w/1m
N/A
N/A
50Hz - 22kHz
150 watts
10 ½” x 5”
Each
Pair
MK-640
Ceiling Speakers
1” Pivoting Titanium
Tweeter
6 ½” Polypropylene
8
92dB 1W/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
32Hz - 22kHz
150 Watts
7 ⁄”
Pair
ICE-645
Pro Series Ceiling Speakers
1” Pivoting Silk High
Tenacity Teteron
6 ½” Polypropyle
8
92dB
N/A
N/A
36Hz - 22kHz
175 Watts
Pair
Page 7
In-Ceiling Model
ICE-640
ICE-630
ICE-620ST
ICE-620
Speaker
Tweeter:
Woofer:
Impedance:
Sensitivity:
Contour Switches:
Frequency Response:
Power Handling:
Dimensions: (D x H)
Wall Cut Out:
Unit of Measure:
ICE-610
6 ½” Contractor Series
Ceiling Speakers
1/2 PEI Dome
6 ½” Polypropylene
8 Ω
88dB
N/A
N/A
60Hz - 22kHz
100 Watts
7 ¾”
Pair
Type:
Pro Series Ceiling Speakers
1” Pivoting Silk Dome
6 ½” Polypropylen
8 Ω
91dB
N/A
N/A
38Hz - 22kHz
150 watts
Pair
MK-550
Ceiling Speakers
1” Pivoting Aluminum
Tweeter
5 ¼” Kevlar Cones
8 Ω
92dB 1W/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
50Hz - 22kHz
150 Watts
6 ½”
Pair
6 ½” Custom LCR Series
Ceiling Speaker
1” Pivoting Silk Dome
6 ½” Polypropylene
8 Ω
91dB
N/A
N/A
52Hz - 22kHz
125 Watts
10 ½” x 5”
MK-540
Ceiling Speakers
1” Pivoting Titanium
Tweeter
5 ¼” Polypropylene
8 Ω
92dB 1W/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
55Hz - 22kHz
125 Watts
6 ½”
Pair
6 ½” Ceiling Speaker
With Back Can
1/2” PEI Dome
6 ½” Polypropylene
8 Ω or 70v
89dB
N/A
N/A
60Hz - 20kHz
100 Watts
9 ½” x 5 ½”
EachPair
ICE-540
Pro Series Ceiling Speakers
¾” Silk Dome
5 ¼” Polypropylene
8 Ω
90dB
N/A
N/A
58Hz - 22kHz
80 Watts
7 ¾” x 2 ¾”
Pair
6 ½” Custom Series
Ceiling Speakers
1” Pivoting Silk Dome
6 ½” Polypropylene
8 Ω
89dB
N/A
N/A
58Hz - 22kHz
125 Watts
7 ¾”
Pair
ICE-530
5 ¼” Custom Series
Ceiling Speakers
¾” Pivoting Silk Dome
5 ¼” Polypropylen
8 Ω
88dB
N/A
N/A
65Hz - 22kHz
100 Watts
8” x 2 ¾”
Pair
e
ICE-520
5 ¼” Contractor Series
Ceiling Speakers
1/2 PEI Dome
5 ¼” Polypropylene
8 Ω
88dB
N/A
N/A
75Hz - 22kHz
90 Watts
8” x 2 ¾”
Pair
Tweeter
ICE-1080HD
3-way 10” Ceiling
Speaker
1 ½” Silk Dome
With 2 ½” Mylar Cone
10” Polypropylene
8 Ω
90dB
N/A
N/A
36Hz - 20kHz
150 Watts
Each
Page 8
Dual Tweeter
Ceiling Speakers
ICE-840TT
ICE-640TT
ICE-620TT
Speaker Type:
Pro Series Ceiling Speaker
Tweeter:
Woofer:
Impedance:
Sensitivity:
Contour Switches:
Frequency Response:
Power Handling:
Dimensions:(D x H)
Ceiling Cut Out:
Unit of Measure: Each Each Each
Dual ¾” Silk Dome
8” Polypropylene
8 Ω
86/89dB
N/A
36Hz - 22kHz
175 Watts
Pro Series Ceiling Speaker
Dual ¾” Silk Dome
6 ½” Polypropylene
8 Ω
86/89dB
N/A
40Hz - 22kHz
150 Watts
6 ½” Custom Series
Stereo Speaker
Dual ¾” Silk Dome
6 ½” Polypropy
8 Ω
86/89dB
N/A
40Hz - 22kHz
125 Watts
7 ¾”
Weather Resistant
Ceiling Speakers
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Contour Switches:
Frequency Response:
Power Handling:
imensions:(D x H)
Ceiling Cut Out:
Unit of Measure:
ICE-800WRS
8” Weather Resistant
Ceiling Speakers
1” Polycarbonate
Tweeter
8” Polypropylene
8 Ω
90dB
N/A
36Hz - 20kHz
150 Watts
Pair
ICE-800WRSTT
8” Weather Resistant
Stereo Ceiling Speaker
Dual 1” polycarbonate
Tweeter
8” Polypropylene
8 Ω
86/89dB
N/A
36Hz - 20kHz
150 Watts
Each
ICE-600WRS
6 ½” Weather Resistant
Ceiling Speakers
1” Polycarbonate
Tweeter
6 ½” Polypropylene
8 Ω
90dB
N/A
48Hz - 20kHz
150 Watts
Pair
ICE-600WRSTT
6 ½” Weather Resistant
Stereo Ceiling Speaker
Dual 1” polycarbonate
Tweeter
6 ½” Polypropy lene
8 Ω
86/89dB
N/A
48Hz - 20kHz
150 Watts
Each
OSD Audio • 1405 Pioneer St • Brea • CA • 92821 • www.osdaudio.com • Tel (562) 697-2600 • Fax (562) 697-2668
Loading...