Page 1
Page 2
OSD
AUDIO
Owner’s Manual
In-Ceiling Speakers
Tools needed for installation
- Pencil
- Drill
- Tape Measure
- Wire cutter
- Philips-head screwdriver
- Sandpaper
- Utility knife
- Safety eyewear
- Gloves
Quick installation guide
- Where is the best place to install the speakers
- Where do the speakers sound the best?
- Try to separate the speakers 6 - 10 feet apart.
- When placing the speakers in the ceiling, try to install them
listening area. (For LCR model only)
- If you intend to paint the grilles, try to do so before installation.
STEP 1:
Trace along the inclusive template. Cut along the traced line using a
drywall saw or rotary drill. A simple, inexpensive drywall saw (about
$10 at your local hardware store) is the best choice for beginners.
Caution: This is the most important part of the entire installation.
If you are not certain whether any obstructions exist behind the
desired mounting area, you should start by cutting a small hole in
the center of your penciled mounting hole with a drywall saw. Use a
piece of sandpaper to sand down the cut out edge for a smoother
contour. (See Diagram 1 )
Cutout Tracing
Speaker wire
To determine the length and the gauge of speaker wire, you will need to
measure the distance between your receiver/amplifier to the speakers.
- Always buy more than you think you would need.
- Equal wire lengths should always be used to maintain an equal
balance in sound volume.
- Sound quality is lost when using thin wire gauge over a long
distance.
18AWG minimum - for distances up to ………………………. . 10 ft
16AWG - from ……………………………………………. 10 to 50 ft
14AWG - from …………………………………………… 50 to 100ft
STEP 3: Tweeter Adjustment
Your in-ceiling speakers come from the factory with the tweeter facing
response. However, you can adjust the tweeter to focus the sound at
your listening location. In order to do this, gently press on the grill (See
Diagram 3). Caution: Do not touch the tweeter dome while adjusting for
your hearing preference. (See Diagram 3) -Pivoting Tweeter Model Only
Diagram 1:
STEP 2: Cut Out
Run the cable into the cut out location while leaving an extra two
feet to make the connection to the speaker easier. Strip back
approximately ½ inch of the speaker cable insulation and twist
the copper wires tightly for easy insertion.
On the back of the speaker, press down on the gold-plated
compression terminal to reveal the "eye" and insert the speaker
cable through the eye for secure connection. Release the compression terminal to lock each cable securely. ( See Diagram 2)
Diagram 2:
Tweeter
Diagram 3:
Adjust the tweeter here
STEP 4: Mounting Dog Ear
Tighten the dog-ear brackets by simply turning the screws on the
slowly clockwise. The quick-turn mounting system and frame will
"sandwich" or clamp around the wall to hold the speaker securely in
place. (See Diagram 4)
Diagram 4:
Dog Ear
LOSE
Mounting Dog Ear
Lock
Page 3
Page 4
In-Ceiling Model
MK-850
ICE-850
ICE-870
MK-840
Speaker Type:
Ceiling Speakers
Tweeter:
Woofer:
Impedance:
Sensitivity:
Contour Switches:
Frequency Response:
Power Handling:
Dimensions: (H x W x D)
Wall Cut Out: (H x W)
Unit of Measure:
ICE-840
Pro Series Ceiling Speakers
1” Pivoting Silk Dome 1” Pivoting Silk Dome
1” Pivoting Aluminum
Tweeter
8” Kevlar Cones
8 Ω
92dB 1W/1m
2-Position Front-Moun
±3dB Bass & Treble Switches
25Hz - 22kHz
200 Watts
Pair
ICE-810
8” Custom Series
Ceiling Speakers
8” Kevlar Ceiling Home
Theater Speakers
1” Pivoting Aluminum
Tweeter
8” Kevlar Cones
8 Ω
92dB
ted
2-Position Front-Mounted
±3dB Bass & Treble Switches
26Hz - 22kHz
175 Watts
Pair
ICE-900ST
8” Ceiling Speaker
With Back Can
1” Coaxial Silk Dome
8” Kevlar LCR Ceiling
Home Theater Speaker
1” Pivoting Aluminum
Tweeter
8” Kevlar Cone
8 Ω
92dB 1w/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
26Hz - 22kHz
175 Watts
Pair
ICE-800ST
8” Ceiling Speaker
With Back Can
1” PEI Dome
Ceiling Speakers
1” Pivoting Titanium
Tweeter
8” Polypropylene
8 Ω
92dB 1W/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
32Hz - 22kHz
175 Watts
Pair
ICE-800
8” Contractor Series
Ceiling Speakers
1/2 PEI Dome
8” Polypropylene
8 Ω
91dB
N/A
N/A
36Hz - 22kHz
175 Watts
Pair
MK-650
Ceiling Speakers
1” Pivoting Aluminum
Tweeter
6 ½” Kevlar Cones
8 Ω
92dB 1W/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
28Hz - 22kHz
175 Watts
Pair
8” Polypropylene
8 Ω
89dB
N/A
N/A
38Hz - 22kHz
140 Watts
Pair
ICE-650
6 ½” Kevlar Ceiling
Home Theater Speakers
1” Pivoting Aluminum
Tweeter
6 ½” Kevlar Cones
8 Ω
92dB 1w/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
30Hz - 22kHz
150 watts
Pair Pair
8” Polypropylene
8 Ω or 70v
89dB
N/A
N/A
40Hz - 18kHz
120 Watts
11” x 7”
Each
ICE-670
6 ½” Kevlar LCR Ceiling
Home Theater Speaker
1” Pivoting Aluminum
Tweeter
6 ½” Kevlar Cone
8 Ω
92dB 1w/1m
N/A
N/A
30Hz - 22kHz
150 watts
8 ¼”
Each
8” Polypropylene
8 Ω or 70v
89dB
N/A
N/A
45Hz - 22kHz
120 Watts
11” x 7”
Each
ICE-660
Pro LCR Ceiling Speaker
1” Pivoting Silk Dome
6 ½” Polypropylen
8 Ω
92dB 1w/1m
N/A
N/A
50Hz - 22kHz
150 watts
10 ½” x 5”
Each
8” Polypropylene
8 Ω
89dB
N/A
N/A
45Hz - 22kHz
120 Watts
Pair
MK-640
Ceiling Speakers
1” Pivoting Titanium
Tweeter
6 ½” Polypropylene
8 Ω
92dB 1W/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
32Hz - 22kHz
150 Watts
Page 5
In-Ceiling Model
ICE-645
ICE-640
ICE-630
ICE-700ST
Speaker
Tweeter:
Woofer:
Impedance:
Sensitivity:
Contour Switches:
Frequency Response:
Power Handling:
Dimensions: (H x W x D)
Wall Cut Out: (H x W)
Unit of Measure:
ICE-620ST
6 ½” Ceiling Speaker
With Back Can
1/2” PEI Dome
6 ½” Polypropylene
8 Ω or 70v
89dB
N/A
N/A
60Hz - 22kHz
100 Watts
9 ½” x 5 ½”
Each
Type:
Pro Series Ceiling Speakers
1” Pivoting Silk High
Tenacity Teteron Dome
6 ½” Polypropylene
8 Ω
92dB
N/A
N/A
36Hz - 22kHz
175 Watts
Pair
ICE-620
6 ½” Custom Series
Ceiling Speakers
1” Pivoting Silk Dome
6 ½” Polypropylene
8 Ω
89dB
N/A
N/A
58Hz - 22kHz
125 Watts
7 ¾”
Pair
Pro Series Ceiling Speakers
1” Pivoting Silk Dome
6 ½” Polypropylene
8 Ω
91dB
N/A
N/A
38Hz - 22kHz
150 watts
Pair
ICE-610
6 ½” Contractor Series
Ceiling Speakers
1/2 PEI Dome
6 ½” Polypropylene
8 Ω
88dB
N/A
N/A
60Hz - 22kHz
100 Watts
7 ¾”
Pair
6 ½” Custom LCR Series
Ceiling Speaker
1” Pivoting Silk Dome
6 ½” Polypropylene
8 Ω
91dB
N/A
52Hz - 22kHz
125 Watts
10 ½” x 5”
Pair
MK-550
Ceiling Speakers
1” Pivoting Aluminum
Tweeter
5 ¼” Kevlar Cones
8 Ω
92dB 1W/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
50Hz - 22kHz
150 Watts
6 ½”
Pair
6 ½” Ceiling Speaker
With Back Can
3/4” Coaxial silk Dome
6 ½” Polypropylene
8 Ω or 70v
88dB
N/A
N/AN/A
55Hz - 18kHz
120 Watts
9 ½” x 5 ½”
Each
MK-540
Ceiling Speakers
1” Pivoting Titanium
Tweeter
5 ¼” Polypropylene
8 Ω
92dB 1W/1m
2-Position Front-Mounted
±3dB Bass & Treble Switches
55Hz - 22kHz
125 Watts
6 ½”
Pair
ICE-540
Pro Series Ceiling Speakers
¾” Silk Dome
5 ¼” Polypropylene
8 Ω
90dB
N/A
N/A
58Hz - 22kHz
80 Watts
7 ¾” x 2 ¾”
Pair
OSD Audio • 1405 Pioneer St • Brea • CA • 92821 • www.osdaudio.com • Tel (562) 697-2600 • Fax (562) 697-2668
ICE-530
5 ¼” Custom Series
Ceiling Speakers
¾” Pivoting Silk Dome
5 ¼” Polypropylene
8 Ω
88dB
N/A
N/A
65Hz - 22kHz
100 Watts
8” x 2 ¾”
Pair
ICE-520
5 ¼” Contractor Series
Ceiling Speakers
1/2 PEI Dome
5 ¼” Polypropylene
8 Ω
88dB
N/A
N/A
75Hz - 22kHz
90 Watts
8” x 2 ¾”
Pair
ICE-1080HD
3-way 10” Ceiling
Speaker
1 ½” Silk Dome Tweeter
With 2 ½” Mylar Cone
10” Polypropylene
8 Ω
90dB
N/A
N/A
36Hz - 20kHz
150 Watts
Each
Loading...