TA-110 & TA-210 Tonearms
Technical Data
TA-110 9 inch static-balance tonearm TA-210 12 inch static-balance tonearm
Effective mass without headshell 3.5 g
Effective arm length (distance between
the stylus and pivot point) 231 mm
Mounting distance (distance between
the pivot point and turntable centre) 213 mm
Offset angle 23.9 degrees
Overhang 18 mm
Tracking force adjusting range
(direct reading) 0-3 g/ 0-4 g
Height adjustment range 35-55 mm
Diameter of the armbase mounting hole 19-20 mm
Diameter of the centre shaft of tonearm 18 mm
Inner null point 66 mm
Outer null point 120.9 mm
Counterweight for cartridge + headshell mass between
18 and 28 g included
Headshell LH-2000E included
Headshell weight 15.5 g
TA-110 total weight including headshell 470 g
Tonearm cable 6NX-TSW-1010 included
Extra mass ring for heavier cartridges included
Extra mass ring weight 45 g
Effective mass without headshell 5 g
Effective arm length (distance between
the stylus and pivot point) 329 mm
Mounting distance (distance between
the pivot point and turntable centre) 316.6 mm
Offset angle 16.5 degrees
Overhang 12.4 mm
Tracking force adjusting range
(direct reading) 0-3 g/ 0-4 g
Height adjustment range 35-55 mm
Diameter of the armbase mounting hole 19-20 mm
Diameter of the centre shaft of tonearm 18 mm
Inner null point 66 mm
Outer null point 120.9 mm
Counterweight for cartridge + headshell mass between
21 and 28 g included
Headshell LH-2000E included
Headshell weight 15.5 g
TA-210 total weight including headshell 536 g
Tonearm cable 6NX-TSW-1010 included
Extra mass ring for heavier cartridges included
Extra mass ring weight 45 g
Ortofon A /S | Stavanger vej 9 | DK-4900 Nakskov | Denmark | Tel. + 45 54 91 19 15 | www.ortofon.com
TA-110 & TA-210 Tonearms
Built upon the TA-100 and two areas of Ortofon’s technological know-how, TA-110 and the new TA-210 have
gone to the next level by reducing unwanted vibrations in the tonearm.
Expertise in materials and compounds is one of the cornerstones
of Ortofon’s technology platform that was applied along developing
the TA-110 and TA-210 tonearms. As a specialist in technical
rubber, Ortofon used one of its special rubber compounds when
creating the specially shaped rubber insert with high vibration
dampening properties for TA-110 tonearm. The TA-110 was given a
precision machined slit in the middle of the aluminium tube, and
a piece of Ortofon’s special vibration damping rubber was
inserted into the slit. An armtube without slit and rubber
damper is symmetrical in a vertical and lateral plane
with respect to vibrations. The slit breaks this
symmetry, and mounting the rubber insert
gives the desired damping.
The TA-110 and TA-210 armtubes are a lot less stressed than conventional armtubes due to the Technical rubber and TPE excellent damping
properties. Both inserts integrated in the tonearm tube are manufactured at the Ortofon technical facilities in Nakskov, Denmark.
Ortofon’s extensive knowledge of vibration properties and characteristics in different shapes and materials has been applied for optimization of
TA-110 and TA-210 tonearms. TA-110 and TA-210 are the products with great benefits for the discerning analogue user.
• Tonearms are static balanced gimbal type arms, easy to use and adjust for
optimal VTF settings.
• Tonearms are equipped with a standard headshell connector
• The tonearms have a standard 5-pin DIN connector for tonearm cable
• The tonearms geometry allows for a Baerwald alignment
(also the IEC recommendations)
• Counter weight will work with headshell+cartridge mass
approximately in the range 20 to 28 gram
• Extra mass ring for heavier combinations is included
The TA-210 tonearm is further improved with two impor tant
changes. The tonearm is given a precision machined slit in each
end of the aluminum tube. Due to positioning of slits, the tube
retains its strength, and distributed damping is provided. A piece
of Ortofon special vibration damping compound is integrated into
each slit: Rubber inserts with high vibration damping properties
and Special proprietary TPE compound with excellent damping
properties are integrated respectively in the bottom and top slit
of the arm tube. Due to these two different materials
an extended damping effect is obtained in
the largest possible range.
TA-110 and TA-210 tonearms can ideally be combined with Ortofon Exclusive series cartridges:
MC Windfeld, MC A90 and the new Expression.
The new High-end headshell LH-10000, incorporating damping technology similar to the tonearms, will be a perfect interface
between TA-110/210 and Ortofon Cadenza series cartridges, MC Windfeld and MC A90.
Ortofon A /S | Stavanger vej 9 | DK-4900 Nakskov | Denmark | Tel. + 45 54 91 19 15 | www.ortofon.com
Loading...