Orthofab Tango User Manual

Download

USER MANUAL

July 2008

Please give this manual to the owner of the wheelchair.

Please read this manual in it entirety before using your

wheelchair for the first time. Read this manual until it becomes familiar and pay close attention to the warnings.

If you have any questions about non-covered subjects in this manual, please consult a technician in an authorized service center or contact our customer service at: 1-(418)-847-5225

Center:

Address:

Phone:

The adjustments of your wheelchair must be made by a health care professional. Inadequate adjustments can cause wounds and/or damage to the user, the caregiver, the wheelchair or the environment.

Do not install unauthorized accessories. Always consult a health care professional for any modifications to your

wheelchair.

is proud to count you among its customers and thanks you for having

chosen one of its products. All the products manufactured by

respect or exceed the highest standards

of quality and safety currently in force in the industry.

personnel is guided

by the desire to satisfy customers expectations. This is why

does not hesitate to offer a most complete warranty, applying to the whole wheelchair elements and components. However, the warranty does not apply to parts and components damaged by abuse, carelessness, accident and normal use or installed and modified by an unauthorized person.

This operating instructions manual has been written to enable you to use your

wheelchair safely. You will find in this document, information

relating to safety, operating instructions and adjustments.

In order to optimize the performance of your

and to extend is lifespan, it is essential to have it check regularly by a technician from an authorized service center.

refuse any responsibility for physical injuries or damages resulting from an improper use of its products, from a lack of precaution in their use or from a modification made without it written assent.

TABLE OF CONTENTS

1 SAFETY REQUIREMENTS......................... .. .. ... .. .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. ... .. .. .. .. .. .. 6

1.1 SAFETY REQUIREMENTS......................... .. .. ... .. .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. ... .. .. .. .. .. .. 6

1.1.1 BEFORE TAKING THE ROAD ................................................................................................... .....6

1.1.2 MOVING WITH THE WHEELCHAIR.................................................................................. .............7

1.1.3 TO CARRY OUT TRANSFERT .......................................................................................................7

1.1.4 VARIOUS HANDLING OPERATIONS.............................................................................................8

1.1.5 CLEANING AND MAINTENANCE OF COMPONENTS...................................... ............................9

1.2 WHAT ABOUT THE ELECTROMAGNETIC ENERGY........................... .. .. .. .. .. .. 9

1.2.1 CAUTION................................................................................................................. ......................10

1.2.2 USING TRANSMITTERS AND RECEIVERS................................................................................10

2 RECOMMENDED USE...................................................................................... 11

3 SPECIFICATIONS............................................................................................. 12

4 SETUP INSTRUCTIONS ......... ... .. .. .. .. .. ... .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. 13

4.1 FOOTREST........................................................................................................ 13

4.1.1 LEGREST LENGHT ADJUSTMENT............................................................................... ...............13

4.1.2 CHANGING FOOTPLATE ANGLE................................................................................................14

4.1.3 CHANGING POSITION (DEPTH) OF THE COMPOSITE FOOTPLATE ......................................14

4.1.4 CHANGING CALF PAD HEIGHT...................................................................................................15

4.1.5 CHANGING CALF PAD POSITIONS.............................................................................................15

4.2 ADJUSTABLE «U» SHAPE ARMREST HEIGHT............................................. 16

4.2.1 TO PROHIBIT REMOVING THE ARMREST.................................................................................16

4.2.2 TO PROHIBIT ADJUSTMENT IN HEIGHT....................................................................................16

4.3 TELESCOPIC ARMREST «T» SHAPE............................................................. 17

4.3.1 TO LIMIT THE TELESCOPIC ARMREST HEIGHT ADJUSTMENT.............................................17

4.4 DYNAMIC BACKREST...................................................................................... 18

4.4.1 DYNAMIC BACKREST INSTALLATION ......................................................................... ... ........ ...18

4.4.2 DYNAMIC BACKREST ADJUSTMENT............................................ .... .... .... .... ... .... ........ ... .... .... ...20

4.5 ADJUSTABLE BACKREST.............................................................................. 21

4.5.1 CHANGING THE BACKREST ANGLE............................................. ........ .... ... .... .... .... ... .... .... .... ...21

4.5.2 CHANGING THE BACKREST HEIGHT ................................................................................. .......23

4.5.3 STABILIZER BAR WITH HEADREST SUPPORT............................ .............................................24

4.5.4 STABILIZER BAR WITH HEADREST SUPPORT AND ADJUSTABLE ANGLE PUSH HANDLE25

4.5.5 ADJUSTABLE ANGLE PUSH HANDLE........................................................................................26

4.6 SEATING ADJUSTMENTS ............................................................................... 28

4.6.1 CHANGING SEAT DEPTH............................................................................................................28

4.6.2 CHANGING SEAT HEIGHT...........................................................................................................29

4.6.3 MAXIMUM TILT ANGLE ADJUSTMENT.......................................................................................32

4.7 SEAT WITH MOTORIZED TILT MECHANISM ................................................. 33

4.7.1 DISMANTLING BEFORE INSTALLATION....................................................................................33

4.7.2 UPPER ANCHOR INSTALLATION................................................................................................33

4.7.3 LOWER ANCHOR INSTALLATION...............................................................................................34

4.7.4 BATTERIES COMPARTMENT INSTALLATION...........................................................................35

4.7.5 CONTROL BOX AND ITS SUPPORT INSTALLATION ................................................................37

4.7.6 CABLE WINDER INSTALLATION.................................................................................................38

4.7.7 TILT MECHANISM POSITIONING SYSTEM ADJUSTMENT.......................................................39

4.8 FRONT WHEELS .............................................................................................. 40

4.8.1 TO CHANGE THE FRONT PART OF THE FRAME OR THE FRONT WHEEL POSITIONS.......40

4.8.2 CHANGING THE TYPES OF WHEELS AND HEIGHT (FRONT AND REAR) .............................41

4.9 REAR WHEELS (standard propulsion)..... .. .. ... .. .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. 42

MID-WHEELS (central propulsion) ............................................................................ 42

4.9.1 CHANGING REAR WHEEL MODEL.............................................................................................42

4.9.2 CENTER OF GRAVITY ADJUSTEMENT......................................... .............................................44

4.9.3 CHANGING MID-WHEEL AXLE POSITION..................................................................................47

4.9.4 CHANGING THE OVERALL WIDTH.............................................................................................48

TABLE OF CONTENTS

4.9.5

TO INSTALL 12 INCHES REAR WHEELS....................................................................................50

4.10 PARKING BRAKES .......................................................................................... 52

4.10.1 TO ADJUST THE POSITION OF THE PARKING BRAKE (Pushing or pulling brake type)..........52

4.10.2 TO CHANGE THE BRAKE LEVERS.................................................................................. ...........56

4.10.3 TO CHANGE THE ANGLE OF THE BRAKE LEVER (pushing brake type only)..........................58

4.11 ANTI-TIPPERS.................................................................................................. 59

4.11.1 HEIGHT ADJUSTMENT ................................................................................................................59

4.12 TILT MECHANISM .................. ... .. .. .. .. .. ... .. .. .. .. ... .. .. .. .. .. ... .. .. .............................. 61

4.12.1 TO ADJUST THE FORCE REQUIRED TO TILT...........................................................................61

5 OPERATING INSTRUCTIONS.......................................................................... 62

5.1 «U» SHAPE REMOVABLE ARMREST............................................................. 62

5.1.1 TO SWINGAWAY ..........................................................................................................................62

5.1.2 TO REMOVE AND/OR INSTALL...................................................................................................63

5.1.3 HEIGHT ADJUSTMENT ................................................................................................................63

5.2 ADJUSTABLE « T » SHAPE ARMREST................... .. ... .. .. .. .. .. ... .. .. .. .. ... .. .. .. .. .. 64

5.3 FOOTREST / LEGREST.................................................................................... 65

5.3.1 SWINGAWAY.................................................................................................................................65

5.3.2 TO REMOVE AND/OR INSTALL...................................................................................................67

5.3.3 TO RAISE OR LOWER THE LEGRESTS.....................................................................................67

5.3.4 RETRACTABLE FULL LENGTH LEGREST..................................................................................68

5.4 BACKREST....................................................................................................... 71

5.4.1 TO FOLD THE BACKREST...........................................................................................................71

5.4.2 RECLINING BACKREST...............................................................................................................72

5.5 SEAT TILT MECHANISM........... .. .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. ..................................... 73

5.5.1 BACKWARD TIPPING...................................................................................................................73

5.5.2 FORWARD TIPPING.....................................................................................................................73

5.5.3 TILT WITH THE MOTORIZED TILT MECHANISM.......................................................................74

5.5.4 RECHARGING BATTERIES................................................................................ ........ .... ... .... .... ...75

5.6 REAR WHEELS............... .. .. .. .. ... .. .. .. .. ... .. .. ..................................... .. .. .. .. ... .. .. .. .. 77

5.6.1 TO REMOVE AND/OR INSTALL...................................................................................................77

5.6.2 PNEUMATIC TIRE PRESSURE....................................................................................................77

5.7 PARKING BRAKES .......................................................................................... 78

5.7.1 TO APPLY AND DISENGAGE THE PARKING BRAKE the PUSHING type ................................78

5.7.2 RETRACTABLE HANDLES............................................... ............................................................78

5.7.3 APPLY – DISENGAGE THE HILL HOLDER.................................................................................79

5.7.4 12 INCHES REAR WHEELS BRAKE............................................................................................80

5.8 ANTI-TIPPERS.................................................................................................. 81

5.8.1 TO REMOVE..................................................................................................................................81

5.8.2 TO SWINGAWAY ..........................................................................................................................81

5.8.3 TO REPLACE.................................................................................................................................82

5.9 SEAT BELT....................................................................................................... 83

5.10 TRANSPORTATION.......................................................................................... 84

5.10.1 ANCHOR POINTS POSITION.......................................................................................................84

5.10.2 ADVICE FOR TRANSPORTATION.......................................................... .... .... ... .... .... .... ... ........ ...85

6 MAINTENANCE................................................................................................. 86

7 BREAKDOWN SERVICE GUIDE...................................................................... 88

8 WARRANTY...................................................................................................... 89

9 AUTHORIZED SERVICE CENTRES................................................................. 91

1. SAFETY REQUIREMENTS

The adjustments of your wheelchair must be made by a health care professional or a technician in an authorized service center.

1 SAFETY REQUIREMENTS

1.1 SAFETY REQUIREMENTS

(Applies to all

wheelchairs)

1.1.1 BEFORE TAKING THE ROAD

• Always put the key switch OFF before getting on or off your vehicle.

• Make sure that the batteries are sufficiently charged (see battery status

indicator).

• Make sure that the anti-tippers are installed.

• Make sure that brakes immobilize your wheelchair completely.

• Make sure that the tire pressure is appropriate.

• Make sure that nothing interferes with wheels (scarf, umbrella, etc…).

• Make sure that your seating position is stable.

• Position the backrest in the raised position.

• Make sure the 45° tilt mechanism is in driving position (seat horizontal with the

ground).

• Fasten your seat belt correctly and without too much slack.

• Make sure that swing away legrests are locked in position and that your feet are

stable on them.

• Push down the elevator legrests.

• Make sure that the swing away or removable armrests are locked in their

positions.

• Make sure that the position of the joystick box enable you to carry out all your movements comfortably and easily.

• Make sure that the joystick rubber cover is in good condition, if not, try to have it fixed as soon as possible.

• Make sure that your personal effects do not block in anyway the wheelchair functions.

• Do not install or transport heavy objects on the backrest of your wheelchair (backpack, bags, grocery, etc).

1. SAFETY REQUIREMENTS

1.1.2 MOVING WITH THE WHEELCHAIR

• Avoid any shock to the joystick box or the joystick itself.

• Avoid slippery surfaces (snow, ice, etc).

• Do not change direction abruptly at high speed.

• Do not use your wheelchair on expressways or streets with intense car circulation.

• Do not transport passengers.

• Do not use your wheelchair under extreme climatic conditions (storm, rain, etc).

• If you drive outside at night, ensure that you will be seen by others.

• Do not approach a slope in a diagonal trajectory, always approach the slope in a

straight line, perpendicularly to the slope.

• Do not go down in a slope in reverse.

• Always actuate the lever gently when you start moving in a slope in order to avoid

tipping the wheelchair.

• Do not make a half-turn in a slope.

• Reduce your speed in restricted or encumbered areas.

• Reduce your speed in a crowd and use your horn to announce your presence.

• In front of an obstacle you must stop and cross it perpendicularly and gradually.

• Avoid thresholds of more than 1 ½ in (38 mm), they can endanger your stability.

• Use the elevators to move you from one level to another.

• Do not approach a slope surface exceeding 10° (17% slope).

• Always fasten your seat belt.

• Keep legs on the legrest while driving.

1.1.3 TO CARRY OUT TRANSFERT

• Always put the on/off switch of the joystick box on the OFF position before carrying out a transfer.

• Never lean forward or backward to reach an object.

• Always place yourself sideway and the near est you can to the object to reach.

• Use the transfer supports on the armrests to raise yourself, after you made sure that

they are correctly in position.

• If your backrest is inclined, do not sit down on the backrest, you could damage the backrest and tip the wheelchair.

• Do not raise yourself upright on the footplates, you could damage and/or tip the wheelchair.

• Do not sit on the armrests. The wheelchair could tip over.

1. SAFETY REQUIREMENTS

1.1.4 VARIOUS HANDLING OPERATIONS

Never try to recharge the batteries in your bedroom while you sleep. During recharge, batteries can produce a harmful gas who can cause you health problem.

• Do not immerse your wheelchair, it could cause a dangerous electrical problem.

• Do not store or leave your wheelchair without someone taking care of it.

• Do not leave your wheelchair under the rain.

• Do not store your wheelchair in a wet or very cold place, this could cause a

dangerous problem on your motorized wheelchair.

•

does not limit nor exclude that the user remains seated in his wheelchair when using a road vehicle adapted for transportation (paratransit), provided the driver and the owner of the aforesaid road vehicle respects, on this subject, all legislative requirements, rules, laws, protocols, directives, norms, standards, instructions and recommendations pertaining to such use by competent authorities.

• Do not travel on tilted surfaces when the wheelchair is in free wheel. If you have to do it, the caregiver must always be oriented in the direction of the bottom of the slope.

• Do not raise the wheelchair by its detachable components (armrest, seat, etc).

• Do not use your battery charger in a hermetic place (backpack, drawer, etc.).

• Always put the on/off switch of the charger on the OFF position before

disconnecting the charging connector on the wheelchair.

• Never try to modify the connector (110 V AC) of the battery charger.

• Never try to modify the battery charger connector (24 V DC) which connect to the

wheelchair.

• Never try to recharge the batteries in your bedroom while you sleep.

• Never connect an electric component other than those manufactured by

• Never modify the electric circuit of the wheelchair.

• Always protect the joystick box when you have to carry the wheelchair.

• Always immediately replace any damaged electric wires.

• Always carry out regularly maintenance of your motorized wheelchair as

recommended by

1. SAFETY REQUIREMENTS

1.1.5 CLEANING AND MAINTENANCE OF COMPONENTS

• Clean as soon as possible your joystick box once it been soiled.

• Use a soft rag and a diluted soft soap.

• Do not use detergent based on alcohol or thinner.

• Regularly carry out maintenance of your wheelchair as recommended by

1.2 WHAT ABOUT THE ELECTROMAGNETIC ENERGY

All electronic instruments which transmit remote informations are generally apparatus which emit in the environment some radio waves. These radio waves are called " electromagnetic energy ".

The functionality of an electronic instrument can be deteriorated by this electromagnetic energy field. It is what we call " an electromagnetic interference". Stronger the intensity of energy is, greater the risk of bad functional problem of the apparatus increase. This energy is measured in volt per meter (V/m).

All motorized wheelchair are suitable to be affected by these interferences. However, current technology makes it possible to immunize them against these risks. It is what is called their electromagnetic level of immunity to the interference, measured also in volt per meter (V/m).

20 V/m is a level of immunity which offer a good protection against the electromagnetic interferences. The electronic parts of the R-NET electronic from

do meet standard directive IEC 1000-4-3.

To avoid electromagnetic interferences, it is important to read and respect the following warning section, before to use your

wheelchair for the first time.

1. SAFETY REQUIREMENTS

1.2.1 CAUTION

Waves emitted by :

• Radio and television stations;

• Amateur radio;

• Radio transmitters and receivers;

• Cellular phones;

• Computers laptop.

CAN AFFECT THE CORRECT FUNCTIONALITY OF MOTORIZED WHEELCHAIR.

1.2.2 USING TRANSMITTERS AND RECEIVERS

• Avoid proximity of these sources of electromagnetic emissions.

• Always put the joystick box in the OFF POSITION before using a cellular phone

or a CB apparatus.

• The addition of electric accessories and/or electric modifications made to the wheelchair will modify its level of immunity to the electromagnetic emissions.

• Always put the key in the OFF POSITION as soon as it safe to do it and that appears an erratic operation with the wheelchair.

• Please forward any incident of this kind to

2. RECOMMENDED USE

2 RECOMMENDED USE

The

manual tilt wheelchair offers all the mechanical characteristics and

necessary functions for easy installation and adjustment of seating products; its structural concept allows assembly of specialized posture components.

The harmonious integration of these characteristics allows you to increase the propulsion function of your client. With the

it is now possible to avoid the usual

compromise between seating products and propulsion of the wheelchair.

3 SPECIFICATIONS

Dimensions

• Weight: 38 lbs*

Note

: The weight does not include rear wheels and the footrests.

• Overall length: with a 20 " wheel = 27 " to 33 "

• with a 22 " wheel = 28" to 34"

Note

: The overall length is measured without the footrest,

• with a 24 " wheel = 29" to 35"

with a depth of 16 inches and includes footrest hanger brackets.

• Overall width : Width + 8 ¼" to + 9 3/4"

• Capacity : 250 lbs

Frame Front wheels

Steel structure Polyurethane 6-7-8 inches Straight frame Pneumatic 6-8 inches Widened frame Foam f illed insert 6-8 inches Epoxy Paint Rigid frame

Rear wheels

Center of gravity adjustment (7 positions, by 1 inch step)

Semi-pneumatic de 20-22-24 inches

Seating (lowered)

Polyurethane 20-22-24 inches

Tilt from -5° to 45°, 3 position for balance adjustment, +/- 25% Pneumatic 20-22-24 inches Motorized tilt mechanism 0° to 35° Foam f illed insert 12-20-22-24 inches Width: 14-15-16-17-18-19-20 inches Spoke wheels 20-22-24 inches Depth: 16-17-18-19 inches or 19-20-21-22 inches Mag wheels 20-22-24 inches Rigid seat or rigid elastic seat Profiled or straight cushion Adjustable height from 14-15-16-17-18 or 19 inches

Handrims

Aluminum 20-22-24 inches

Backrest (Dynamic)

Plastic coated 20-22-24 inches

Adjustable angle and foldable 90°-95°-100°-105°-110°-115°-120°

Foam coated 20-22-24 inches

Reclining with pneumatic actuator 90° to 160° Height adjustment from 16 to 25 inches

Reclining height 16 to 25 in

Wheel locks

Strap backrest Standard wheel lock (pushing or pulling) Adjustable tension strap backrest Adjustable angle handles Stabilizer bar with headrest support

Wheel lock extension

Adjustable angle push handle

Hill holder

Headrest

Inaccessible to the user (with foot)

Articulated 3 axis articulated

Armrest

Seat to floor height chart

Swingaway Adjustable height from 10 to 14 inches option: 8 to 12 inches or 6 to 8 inches

Front

wheels

Rear

wheels

Minimum front an d rear

seat to floor height

3 positions, 1” inch step

Armrest upholstery length 10 or 14 inches 6 inches 20 inches 14 inches Width of armrest upholstery 2 inches 6 inches 12 inches 15 inches

Footrest

7 inches 12 inches 15 inches

Length adjustment from: 14 to 19 inches Length modification: less than 14 inches or more than 19 inches

7 inches 8 inches

22 inches 24 inches

15 inches

16 inches Swing away – removable Angle 60° / 70° parallel or tapered 90° angle parallel only

Elevating Articulated Assisted elevation system

Footplates

Foldable Composite Aluminum narrow or large Aluminum narrow or large, angle adjustable Aluminum full width Heel loops Toe loops Front roller bumper

L.U.+ 8¼ "

4 SETUP INSTRUCTIONS

After having carried out an adjustment and before using the wheelchair, make sure that all hardware is tight. Make sure that all functions are secure before using the wheelchair.

The adjustments of your wheelchair must be made by a health care professional. Inadequate adjustments can cause wounds and/or damage to the user, the caregiver, the wheelchair or the environment.

4.1 FOOTREST

4.1.1 LEGREST LENGHT ADJUSTMENT

Figure 1 : To change legrest length.

a) To adjust the length of all types of footrest (see; figure 1):

1. Remove the (A) adjustment screw, using a 7/16" wrench;

2. Adjust the telescopic tubing (C) at the needed length;

3. Put back the (A) screw and tighten firmly

TELESCOPIC

TUBING

4 SETUP INSTRUCTIONS

4.1.2 CHANGING FOOTPLATE ANGLE

1. Loosen screw (B) using a 10 mm key;

2. Adjust the footplate at the needed angle;

3. Tighten screw (B) firmly (tighten at 140 Pounds/inch).

Figure 2 : Changing footplate angle.

4.1.3 CHANGING POSITION (DEPTH) OF THE COMPOSITE FOOTPLATE

1. Remove the two (2) Phillips screws (A) at the end of the footplate (see; figure 2);

2. Pull the footplate to release it from the support;

3. Readjust the footplate at the needed depth;

4. Replace the end part of the footplate with the (2) Phillips screws (A).

Aluminum footplate

COMPOSITE FOOTPLATE

INSERTION GROOVE

4 SETUP INSTRUCTIONS

4.1.4 CHANGING CALF PAD HEIGHT

NOTE: The calf pad is adjustable in height, depth and width (see; figure 3).

a) To adjust calf pad height:

1. Loosen screw (A) using a 5 mm Allen key;

2. Slide support (B) until you reach the needed position;

3. Put back screw (A) and tighten firmly.

NOTE

: The calf pad is not adjustable in height with the articulated legrest.

Figure 3 : Calf pad adjustment.

4.1.5 CHANGING CALF PAD POSITIONS

a) To adjust calf pad width (see; figure 3):

1. Loosen screws (C) using a 4 mm Allen key;

2. Slide calf pad (D) until you reach the needed position;

3. Tighten screws (C).

b) To adjust calf pad depth (see; figure 3):

1. Loosen screw (E) using a 5 mm Allen key;

2. Loosen screw (F);

3. Adjust at the needed position and tighten screws (E) and (F).

4 SETUP INSTRUCTIONS

4.2 ADJUSTABLE «U» SHAPE ARMREST HEIGHT

4.2.1 TO PROHIBIT REMOVING THE ARMREST

The (A) screw located at the base of the armrest, gives the possibility of installing in a permanent way the armrest to the wheelchair. This removes the "DETACHABLE" function of the armrest while preserving the swingaway possibility. Loosen the counter-nut (8 mm key), and screw (4 mm Allen key) the bolt (A) in the hole and tighten the counter-nut (see; figure 4-A).

Figure 4-A : To block the possibility of taking off the "U" shape armrest.

4.2.2 TO PROHIBIT ADJUSTMENT IN HEIGHT

The screw (A) located at the back of the armrest gives the possibility of prohibiting the adjustment in height of the armrest. To prohibit t he height adjustment, loosen the counter-nut (8 mm key), screw (4 mm Allen key) the bolt (A) in the hole and tighten the counter-nut (see; figure 4-B).

Figure 4-B : To block the height adjustment of the "U" shape armrest.

4 SETUP INSTRUCTIONS

4.3 TELESCOPIC ARMREST «T» SHAPE

4.3.1 TO LIMIT THE TELESCOPIC ARMREST HEIGHT ADJUSTMENT

Figure 5: Armrest height adjustment limitation.

It is possible to limit the telescopic armrest height adjustment. You just have to move the (2) limitation blocks, using a 5/32” Allen key and tighten them at the needed position (see; figure 5).

NOTE

: This armrest is not removable.

4 SETUP INSTRUCTIONS

4.4 DYNAMIC BACKREST

4.4.1 DYNAMIC BACKREST INSTALLATION

POSITION ANGLE

1 90°

(std)

2 95° 3 100° 4

NON-

AVAILABLE

NON-

AVAILABLE

NON-

AVAILABLE

NON-

AVAILABLE

Figure 6-A: Dynamic backrest angles adjustment positions.

NOTE :

The way to change the dynamic backrest angle, is the same as per section

4.5.1, the only difference with the dynamic backrest is to don’t forget to move the nylon washers (C) following the new angle position (see; figure 6-B).

Consult the figure 6-A above to know the possible adjustment angles and to

tighten the screws at 20 pounds/inch

It is important to use only the 1 to 3 positions of the figure 6-A table above, to not damage the dynamic backrest system.

The adjustments of your wheelchair must be made by a health care professional. Inadequate adjustments can cause wounds and/or damage to the user, the caregiver, the wheelchair or the environment.

4 SETUP INSTRUCTIONS

Figure 6-B: Dynamic backrest installation on the wheelchair.

1. Determine at which angle the backrest should be installed.

2. Take the backrest structure tubing (G) and insert the compression piston (D) equal to the oblong hole in the same way as shown at figure 6-B. The compression piston (D) should be sprayed with grease before insertion.

3. Spray with grease the 4 nylon washers (C) and put two of them on the inside in line with the bottom holes on the anchor structure (H). The grease should retain the nylon washers stick to the anchor structure (H) (see; figure 6-B).

4. Take the backrest structure tubing (G) with the compression piston (D) and install it on the anchor structure (H). Once that the two (C) nylon washers, the compression piston (D) and the oblong hole on the backrest structure tubing will be all aligned, insert the (A) screw, the (B) nut and tighten, using two 7/ 1 6 " k ey.

NOTE: Tighten the screws at 20 pounds/inch. This tightening force should allow the dynamic backrest assembly to move freely.

5. Take the two others (C) nylon washers and put them on the inside in line with the adjustment angle holes on the anchor structure (H).

4 SETUP INSTRUCTIONS

6. Adjust the backrest structure tubing (G) at the desired angle and once the (C) nylon washers and the holes in the backrest structure tubing (G) will be all aligned, insert the full threaded (A) screw and tighten the (B) nut, using two 7/16" key (see; the note at step 4, in reference to know about the tightening force to use).

7. Insert the (E) spring beforehand sprayed with grease in the bottom part of the backrest structure tubing (G) shown at figure 6-B.

8. Spray with grease the threaded part of the spring tension adjustment handle (F).

9. Screw the spring tension adjustment handle (F) on the bottom part of the backrest structure tubing (G) until you can see only two threads (this is the NEUTRAL position at this position the spring is not compressed yet).

4.4.2 DYNAMIC BACKREST ADJUSTMENT

It is possible to choose 3 different types of springs with the dynamic backrest. 3 springs with different compression hardness. The RED spring (soft tension), the BRONZE spring (regular tension) and the GREEN spring (hard tension).

1. Insert the selected (E) spring in the bottom part of the backrest structure tubing (G) and screw the spring tension adjustment handle (F) until you can not see any threads (the spring will be a little bit compressed) (see; figure 6-B).

2. Refer to the graduated sticker (I) to know the maximum compression of each springs (see; figure 6-B). For example

; the green spring, will reach its maximum compression, when the handle (F) will be in line with the number 3 on the sticker (I).

3. The final adjustm ent will depend on each us er comfort. Moreover, this adjustm ent could be different on each backrest post.

Never put your hands on the spring tension adjustment handle (F) during somebody use the dynamic backrest.

4 SETUP INSTRUCTIONS

4.5 ADJUSTABLE BACKREST

4.5.1 CHANGING THE BACKREST ANGLE

POSITION ANGLE

1 90o 2 95

o (std)

3 100o 4 105o 5 110o 6 115o 7 120o

Figure 7-A: Backrest angle positions.

The adjustments of your wheelchair must be made by a health care professional. Inadequate adjustments can cause wounds and/or damage to the user, the caregiver, the wheelchair or the environment.

UPPER ROW HOLES

BOTTOM ROW

HOLES

4 SETUP INSTRUCTIONS

To adjust the backrest angle (see: figure 7-A):

1. Unscrew (B) nut (using a 7/16" wrench) do this on each side of the backrest structure;

2. Position yourself behind the backrest, and take off the (A) screw on each side by pushing lightly on the backrest to help.

• Caution

: Once both screws are removed, the backrest will be free to

swing away towards you.

3. Put back in position the backrest angle adjustment (A) screws by choosing one of the 7 holes in the way to obtain: 90°, 95°, 100°, 105°, 110°, 115° or 120° as shown on figure 7-A;

4. Tighten (A) screws and (B) nuts on each side of the backrest structure.

Figure 7–B : Backrest angle adjustment.

4 SETUP INSTRUCTIONS

4.5.2 CHANGING THE BACKREST HEIGHT

To change the backrest height, unscrew the (A) screw (using a 7/16" wrench) located on each backrest structure. Choose the height by placing the threaded hole on the backrest post in line with one of the 5 holes (H1 to H5) on the backrest structure tubing and then screw back the (A) screw in position. Tighten firmly. (see; figure 8).

Figure 8 : To change backrest height.

(A)

SCREW

BACKREST

STRUCTURE TUBING

BACKREST

POST

4 SETUP INSTRUCTIONS

4.5.3 STABILIZER BAR WITH HEADREST SUPPORT

For a better comfort, it is possible to put a headrest on the

wheelchair,

to do this :

1. Cut out the end of the rubber handles on the backrest handle;

2. Using a 5/32" Allen key, tighten the (A) screw at each side of the push bar on the end of the backrest post that you just took out on step 1 (see; figure 9).

3. Tighten firmly both (A) screws.

Figure 9 : Stabilizer bar (push bar) with headrest support.

BACKREST

POST

PUSH BAR

(A)

SCREW

HEADREST

SUPPORT

4 SETUP INSTRUCTIONS

4.5.4 STABILIZER BAR WITH HEADREST SUPPORT AND ADJUSTABLE ANGLE PUSH HANDLE

1. To install a cross bar with a headrest support; unscrew and remove on each side the (C) screw and the (E) nut, using a 5/32" Allen key and a 3/8" wrench, make sure to keep the (2) (D) washers.

2. Separate the backrest handles from the adjustable angle push handle.

3. Remove both diameter reduction bushing inside the arm of the adjustable angle push handle and replace them with the (2) cross bar bushing (see; figure 10).

4. Cut (1 ½" approximately) off the black rubber on the backrest post structure

(see; figure 10).

5. Reinstall the backrest post inside the cross bar bushing and once the hole of the backrest post and the cross bar bushing will be aligned, tighten the (H) screws and the (G) nuts and for the adjustable angle push handle, screw back the (C) screws, (E) nuts, don't forget to put back the (D) washers.

6. Fix the cross bar with headrest support under the cross bar bushing using (A) screws, (B) washers and (F) nuts, using a 7/16” wrench and a 5/32" Allen key.

Figure 10 : Stabilizer bar with headrest support and adjustable angle push handle.

1 1/2"

BACKREST

POST

4 SETUP INSTRUCTIONS

4.5.5 ADJUSTABLE ANGLE PUSH HANDLE

Figure 10-A : Adjustable angle push handle.

a) Width adjustment (see; figure 10-B.1) :

1. Insert the tubing one into t he other and slide until you will reach the neede d width.

2. Use a Phillips screwdriver insert in the middle hole and t ighten (A) screw, (B) washers and (C) nut firmly. (Use a 3/8" wrench and a 5/32" Allen key).

Figure 10-B.1 : Width adjustment.

b) Installation of the adjustable angle push handle (see; figure 10-B.2) :

1. Cut out the end of the rubber handles on a length of 1 ½”;

2. Locate the insertion part of the adjustable angle push handle in the

backrest post, using a screwdriver to help. Put the (A) screw, (B) washer and (C) nut and tighten firmly (Use a 3/8" wrench and 5/32" Allen key).

Width –1"

4 SETUP INSTRUCTIONS

Figure 10-B.2 : Backrest handle and adjustable angle push handle assembly.

c) Handle assembly (see; figure 10-C) :

1. Remove the handles from the backrest post or from the cross bar and reinstall them on the adjustable angle push handle;

2. Using a 4 mm Allen key, unscrew both (A)screws in the handle upper part. Both parts (Upper and Bottom) are now separated;

3. Put back the handles without tighten (A) screws too much. Position the handles in the way to be comfortable when using the push handle.

Figure 10-C : Handles assembly.

Cut 1½"

Fixation hole at 1"

BACKREST

POST

INSERTION PART OF THE

ADJUSTABLE ANGLE PUSH

HANDLE.

HANDLE

UPPER PART

HANDLE

BOTTOM

PART

4 SETUP INSTRUCTIONS

4.6 SEATING ADJUSTMENTS

4.6.1 CHANGING SEAT DEPTH

The seat depth can be easily adjusted, using the same components found on the wheelchair to 16, 17, 18 and 19 inches or 19, 20, 21 and 22 inches. (see; figure 11).

To do it :

1. Unscrew and remove the (A) screw and (B) nut (using a 7/16" wrench);

2. Make t he footrest hanger bracket (C) slide into seat structure tubing (F) until you get the needed depth and position the (A) screw to tighten the assembly;

3. When you extend seat depth more than 16 inches or 19 inches depending which seat structure (F) you have, you will need to install the (D) seat support to support the seat plate;

4. Once the depth is determined, replace the (A) screw and tighten the armrest support with the (B) nut (make sure to replace the washer);

5. Fix the (D) seat support on the footrest hanger bracket (C) with the (E) screw, using a 5/32" Allen key and position the (D) seat support always in the farthest hole from the (A) screw.

Figure 11 : Changing seat depth.

When the depth is adjusted, it is necessary to readjust the front wheel position. (see; section 4.8)

4 SETUP INSTRUCTIONS

4.6.2 CHANGING SEAT HEIGHT

Figure 12 : Seat to floor height adjustment.

The

wheelchair allows you to change the seat to floor height in two

different ways (see; figure 12 and table 1 and 2) :

1- The choice of wheels; which means the combination of

front and rear wheel diameters. The adjustment on the fork (P0 to P3) which also allows an adjustment.

2- The seat to floor adjustment on the adjustable height

interface in a range of 3 inches (H1 to H4).

To adjust the height on the adjustable frame interface:

1. Remove the rear wheels either using the quick release axle or remove the

standard threaded axle.

2. Unscrew the (2) bolts (½" wrench) positioned on each side of the frame and

slide the adjustable height interface side by side to the needed positions (Position H1, H2, H3 or H4) Æ see; figure 12.

3. Replace the screws and tighten the nuts firmly, do not forget the washers.

The adjustments of your

wheelchair must be made

by a health care professional. Inadequate adjustments can cause wounds and/or damage to the user, the caregiver, the wheelchair or the environment.

FRAME

ADJUSTABLE HEIGHT

INTERFACE

4 SETUP INSTRUCTIONS

STANDARD CONFIGURATION POSSIBLE CHOICE OF SEAT TO FLOOR HEIGHT, WHEELS AND TILT ANGLES

Table 1 and 2: Standard configuration.

When the seat to floor height is modified, it is always necessary to proceed to a readjustment of the center of gravity and brakes. The change in seat to floor height can modify the tilt angle, refer to the following table to identify the angle range available.

4 SETUP INSTRUCTIONS

MID-WHEEL PROPULSION CONFIGURATION WITH SEAT DEPTH 16" to 19" POSSIBLE CHOICES OF SEAT TO FLOOR HEIGHT, WHEELS AND TILT ANGLES

Table 3: Mid-wheel propulsion configuration.

Figure 13 : Seat to floor height adjustment on a mid-wheel propulsion wheelchair.

NOTE:

1- For the mid-wheel configuration, please follow the same procedure as per the

standard frame.

2- The choice of wheels; which means the combination of front and rear wheel

diameters. The adjustment on the fork (P1 and P2) which also allows an adjustment (see; section 4.6.2).

ADJUSTABLE HEIGHT

INTERFACE

BOLTS

FRAME

4 SETUP INSTRUCTIONS

4.6.3 MAXIMUM TILT ANGLE ADJUSTMENT

In some cases, it will be necessary to limit the tilt angle of the seat. Two (2) devices make it possible to carry out this function (see; figure 14).

a) Limitation of the posterior angle. The tilt allows an angle up to 45°:

1. Loosen (A) screw and (B) nut on the (E) collar (using (2) 7/16" wrench);

2. Bring the tilt mechanism at the needed position;

3. Lower the (E) collar until it touches the gas cylinder;

4. Tighten the (A) screw and (B) nut on the (E) collar, do not forget the (D) washer.

b) Limitation of the anterior angle. The tilt mechanism can give you an angle from -5°

to +45°. The next adjustment gives you the ability to get back to a previous angle position :

1. Loos en the (C) screw on the (G) open collar (using a 1/2" wrench);

2. Bring the tilt mechanism at the needed position;

3. Make sure to insert the limitation angle tubing (F) and the open collar (G) in the limitation bar (H). The system must be engaged (see; figure 14). The open collar (G) must be lowered to make contact with the bottom part of the limitation bar (H);

4. Tighten the (C) screw on the (G) open collar firmly to block the limitation mechanism.

NOTE: The limitation angle tubing (F) can be retracted in order to be able to return to a horizontal position or anterior -5°.

Figure 14 : Maximum tilt angle limitation.

4 SETUP INSTRUCTIONS

4.7 SEAT WITH MOTORIZED TILT MECHANISM

4.7.1 DISMANTLING BEFORE INSTALLATION

1. Apply parking brakes to immobilize the wheelchair.

2. Remove the pneumatic actuator release handles (see; figure 15).

3. Remove all the assembly of the right and left actuator (see; figure 14).

4. To make easier the motorized tilt mechanism assembly, it is recommended to

remove the seat system from the base.

Figure 15 : Remove the pneumatic actuator release handles.

4.7.2 UPPER ANCHOR INSTALLATION

1. Put the upper anchor (D) on the rear corner of the seat interface (C)

(see; figure 16-A).

2. Slide the (B) axles in the rear holes of the seat interfaces (C).

3. Align the (B) axles holes with the threaded ones on the upper anchor (D) centre this assembly on the wheelchair base and tighten the (A) screws firmly, using a 7/16" key (see; figure 16-B).

4. Make sure that both side of the upper anchor (D) will be solidly fixed to the seat interfaces (C).

The seat with motorized tilt mechanism can only be assembled on a mid-wheel TANGO configuration.

4 SETUP INSTRUCTIONS

Figure 16-A : Upper anchor installation.

4.7.3 LOWER ANCHOR INSTALLATION

1. Place the lower anchor (D) on the front corner of the height adjustment interfaces (E) (see; figure 17-A).

2. Insert the "U" shape bolt (C) over the height adjustment interfaces (E) and make the threaded parts pass through the holes of the lower anchor (D).

3. Install the (B) washers and the (A) nuts and tighten them firmly, using a 7/16" key (see; figure 17-B).

4. Make sure that both side of the lower anchor (D) will be solidly fixed to the height adjustment interfaces (E).

Figure 17-A : Lower anchor installation.

Figure 16-B : Final assembly.

Figure 17-B : Final assembly.

4 SETUP INSTRUCTIONS

4.7.4 BATTERIES COMPARTMENT INSTALLATION

1. Open the lower flap (B) on the batteries compartment (see; figure 18-A).

2. Insert the part (C) (see; figure 18-A) of the compartment support extrusion on the lower anchor, make sure that the insertion is complete and solid (see; figure 18-B).

3. Close the lower flap (B) over the lower anchor (see; figure 18-B).

4. Open the upper flap (A) (see; figure 18-A) and take the actuator cable (B) and make it pass thru the bottom part of the batteries compartment (see; figures 18-C and D).

5. Plug the actuator cable ( B) connector with the connector (B) on the motorized tilt mechanism control box cable (see; figures 18-D and E).

6. Plug the red and black connector of the battery charger with the same red and black connector (D) on the motorized tilt mechanism control box cable (see; figures 18-E and F).

7. Plug the 3 connectors (C) on the motorized tilt mechanism control box cable, well identified with stickers with the ones of the positioning system identified with the same stickers (see; figure 18-E).

8. Close the upper flap (A) of the batteries compartment.

Figure 18-A : Motorized tilt mechanism batteries compartment.

4 SETUP INSTRUCTIONS

Figure 18-B : Compartment installed. Figure 18-C : Actuator cable.

Figure 18-D : Actuator and connector. Figure 18-E : Control box and cables.

The batteries

compartment must be

installed just beside the

actuator and the

charger over the frame

cross bar.

(B) FLAP

ACTUATOR

CABLE

4 SETUP INSTRUCTIONS

Figure 18-F : Red and black connectors.

4.7.5 CONTROL BOX AND ITS SUPPORT INSTALLATION

1. Choose the side of assembly (right or left).

2. Remove the (A) screw and the (B) washer which maintains the front part of the armrest upholstery (see; figure 19).

3. Insert the control box support (C) in the armrest tubing and align the hole on the support (C) in line with the one on the armrest tubing.

4. Replace the (A) screw and the (B) washer and tighten firmly.

5. Put in place the tilt mechanism control box (D), install a “Velcro” strip on the contact side of the control box and fix the control box on the support (C) which has already “Velcro” strip apply on both side. The control box must be installed on the outermost side of the support (see; figure 19).

6. Pass the tilt mechanism control box cable on the inner side of the armrest.

4 SETUP INSTRUCTIONS

Figure 19 : Motorized tilt mechanism control box installation.

4.7.6 CABLE WINDER INSTALLATION

1. Use the last hole, on the seat structure frame (F), this hole will be use to fix the charger cable winder (see; figure 20).

2. Fix the charger cable winder as shown at figure 20, take the (A) screw, the (B) washer, the (E) winder, the (D) saddle and the (C) nut, using (2) 7/16" key, tighten the assembly firmly on the seat structure frame.

3. Wind up the charger cable in the charger cable winder (E) to prevent any damage to the cable during use.

Figure 20 : Charger cable winder installation.

4 SETUP INSTRUCTIONS

4.7.7 TILT MECHANISM POSITIONING SYSTEM ADJUSTMENT

NOTE: The motorized tilt mechanism is equipped with 3 electromagnetic cursors which

are easily adjustable. These switches and their connectors are well identified with stickers as shown below (see; figure 21).

Figure 21 : Tilt mechanism positioning system adjustment.

The adjustments of your wheelchair must be made by a health care professional. Inadequate adjustments can cause wounds and/or damage to the user, the caregiver, the wheelchair or the environment.

The (A) switch limits the posterior tilt action.

The (C) switch activate a green LED on the control box, this light will indicate the ideal tilt position to the user.

The (B) switch limits the anterior tilt action.

4 SETUP INSTRUCTIONS

4.8 FRONT WHEELS

4.8.1 TO CHANGE THE FRONT PART OF THE FRAME OR THE FRONT WHEEL POSITIONS

STANDARD PROPULSION CONFIGURATION MID-WHEEL PROPULSION CONFIGURATION

Figure 22 : To change the frame model.

NOTE: The available depth positions are represented by numbers.

The manual tilt

wheelchair has two (2) different front frame models,

a straight model and a tapered model. Moreover, these frames are adjustable in length to adapt to all seat depth. If you have to do the replacement of the front frame or to adjust the position of the

front wheels; follow these steps :

1. Remove the two (A) screws on each side (using a 7/16” wrench);

2. Slide the support at the needed position;

3. Replace the screws and washers in position;

4. Tighten the nuts with a maximum tightening torque of 25 pounds/inch.

The adjustments of your wheelchair must be made by a health care professional. Inadequate adjustments can cause wounds and/or damage to the user, the caregiver, the wheelchair or the environment.

Always check the stability of the wheelchair BEFORE using the maximum tilt angle. Carry out a TEST on the wheelchair BEFORE giving the wheelchair to the user.

(A)

STRAIGHT FRONT

FRAME MODEL

TAPERED FRONT

FRAME MODEL

4 SETUP INSTRUCTIONS

4.8.2 CHANGING THE TYPES OF WHEELS AND HEIGHT (FRONT AND REAR)

1. For a standard propulsion, remove the (A) screw (1/2" wrench) and (B) nut which maintain the wheel to the fork (see; figure 23);

2. For a mid-wheel propulsion, remove (A) screw (using two (2), 1/2" wrench) and (B) nut which maintain the wheel to the fork (see; figure 23);

3. Remove the wheels from the fork;

4. Remove the spacers and washers from the wheel assembly;

5. Select the wheel size and put the screws in the chosen hole (see; tables section 4.6.2);

6. Invert the procedure to reassemble.

NOTE : For the seat to floor height choices ; see section 4.6.2 tables.

STANDARD PROPULSION CONFIGURATION MID-WHEEL PROPULSION CONFIGURATION

Figure 23: To change front (rear) wheels model and height.

The front wheel position is adjusted at the factory as per the seat depth chosen. There is a risk of instability when the seat is farther ahead than the front wheels. In a mid-wheel propulsion configuration rear forks positions don't have to be adjusted.

The adjustments of your wheelchair must be made by a health care professional. Inadequate adjustments can cause wounds and/or damage to the user, the caregiver, the wheelchair or the environment.

With a mid-wheel configuration you always have to change the front, central and rear wheels at the same time.

(P3)

(B)

(A)

4 SETUP INSTRUCTIONS

4.9

REAR WHEELS (standard propulsion)

MID-WHEELS (central propulsion)

4.9.1 CHANGING REAR WHEEL MODEL

The seat to floor height modification can require a change of the rear wheels diameter. To do this:

STANDARD THREADED AXLES

1. To remove the wheel, unscrew the (A) screw and (B) nut, using a 3/4” wrench;

2. To replace the wheel, use a new nut. Avoid tightening the nut too much, the wheel might have difficulty to turn (see; figure 24-A).

Figure 24-A : Threaded axle.

With a mid-wheel configuration you always have to change the front, central and rear wheels at the same time.

NOTE: FOR THE MID-WHEEL PROPULSION IF 5 INCHES WHEELS:

Install the washer at position A. IF 6 INCHES WHEELS:

For the (2) rear wheels, install the washer at the position B and for the (2) front wheels at the position A.

4 SETUP INSTRUCTIONS

QUICK RELEASE AXLE :

1. Push the (A) button and pull the wheel towards you. Grab the wheel from its center (see; figure 24-B) ;

2. To replace, push the (A) button and insert the axle in the housing. Make sure that the axle is locked in position in the housing by the blocking pins (B).

Figure 24-B: Quick release axle.

NOTE : If the axis does not locked, it requires an adjustment. To do it :

1. Remove the axis from the housing ;

2. Use a 7/16” key, to maintain the end of the axis (A) ;

3. Use a 3/4” key, to tighten or loosen (B) nut slightly ;

4. Insert the axis in the wheel and carry out a test. (It is always preferable to have a small side play, once the axle is locked ± 1/64”).

Figure 25 : Quick release axle adjustment.

Make sure that the two (2) blocking pins of the quick release axle are released before using the wheelchair. The blocking pins MUST exceed the housing for a perfect fit. Keep the axle and the blocking pins clean.

4 SETUP INSTRUCTIONS

4.9.2 CENTER OF GRAVITY ADJUSTEMENT

The adjustment of the center of gravity is necessary in order to preserve a good stability of the wheelchair. The

wheelchair allows seven (7) adjustment positions. The choice of these positions is the responsibility of the occupational therapist (see; figure 19).

The tables below, (next page) determines the allowed configurations, and mentions the maximum seat tilt angle.

Figure 26 : Rear wheel axle positions for the center of gravity adjustment.

The adjustments of your wheelchair must be made by a health care professional. Inadequate adjustments can cause wounds and/or damage to the user, the caregiver, the wheelchair or the environment.

There is no center of gravity adjustment if your wheelchair is equipped with a mid-wheel option.

4 SETUP INSTRUCTIONS

The more the position of the wheel increases (+ 1 to + 5) better is the wheelchair stability. The anti-tippers must always be secured to prevent any risk of accidents.

Table 1 and 2 (4.6.2) : Standard configuration.

4 SETUP INSTRUCTIONS

Figure 27-A : Changing rear wheel axle position.

To change the position of the rear wheels (see; figure 27-A) :

1- Remove the rear wheels from the wheelchair. See section 5.6.1; 2- Remove the (A) screws (7/16" key) and (B) nuts which maintains the

housing assembly of the rear wheel axle;

3- Replace the housing assembly for the rear wheel at the needed

position on the frame. Consult the tilt angle table (section; 4.9.2) to identify the new position;

4- Install the (A) screws and (B) nuts and tighten them to a torque of 25

pounds/inch. To do this, use a torque wrench;

The adjustments of your wheelchair must be made by a health care professional. Inadequate adjustments can cause wounds and/or damage to the user, the caregiver, the wheelchair or the environment.

Check the wheelchair stability before delivery to the user.

4 SETUP INSTRUCTIONS

5- Repeat this procedure for the other side ; 6- Replace in position the rear wheels on the wheelchair; 7- Engage the tilt mechanism and carry out a stability test on the

wheelchair;

8- Repeat this entire procedure (1 to 7) until the wheelchair is stable.

4.9.3 CHANGING MID-WHEEL AXLE POSITION

Figure 27-B: Changing mid-wheel axle position.

Table 4: Changing mid-wheel axle position.

NOTE: If you have this configuration: 6 inches front and rear wheels, 22 inches middle wheel and 19 inches depth. You will have to change rear wheels position as per:

with A1

(see; figure 27-B above, to identify the position).

4 SETUP INSTRUCTIONS

To change the position of the mid-wheels (see; figure 27-B) :

1- Remove the middle wheels from the wheelchair. See section 5.6.1 ; 2- Remove the (E) screw s (7/16" key) and (G) nuts, which maintains the

housing assembly for the middle wheel axle. Don't lose the (F) washers;

3- Replace the housing assembly for the middle wheel at the needed

position on the frame. Consult the table 4 and the figure 27-B (section

4.9.3).

4- Install the (E) screws (7/16" key) and (G) nuts and tighten them to a

torque of 25 pounds/inch. To do this, use a torque wrench; 5- Repeat this procedure for the other side; 6- Replace in position the middle wheels on the wheelchair; 7- Engage the tilt mechanism and carry out a stability test on the

wheelchair; 8- Repeat this entire procedure (1 to 7) until the wheelchair is stable.

4.9.4 CHANGING THE OVERALL WIDTH

The manual tilt

wheelchair width can be adjusted.

When the width is reduced to a certain point the swingaway function of the armrests might be impaired.

To do it :

1. Loosen the two (2) nuts, using a 1 1/8” key (see; figure 28-A);

2. Screw the housing as shown at figure 28-A below and leave a space of 1/8" inch between the screw and the nut;

3. Make sure that the threaded parts on the housings are positioned at 90° relatively to the floor (figure 28-B);

4. Tighten the two (2) nuts with a torque of 40 pounds/foot.

NOTE : DO NOT tighten too much because it could deform the housing.

Once the procedure is completed, it will be necessary to adjust the parking brakes as per the instructions of section 4.10.1.

4 SETUP INSTRUCTIONS

Figure 28-A : To change overall width.

Figure 28-B

WHEEL

1/8 po

NUTS

HOUSING

FLAT PART

THREADED PART

4 SETUP INSTRUCTIONS

4.9.5 TO INSTALL 12 INCHES REAR WHEELS

It is possible to assemble 12 inches diameter rear wheels on the

. This assembly can be carried out without significant modifications. To do this, if you choose the foot brake as an option, follow these steps :

Figure 29 : 12 inches wheels installation.

FOOT BRAKE OR

HAND BRAKE

PEDAL

FOOT BRAKE

PEDAL

4 SETUP INSTRUCTIONS

For the 12 inches rear wheels installation (see; figure 29):

1- Remove rear wheels (see; section 5.6.1) ; 2- Remove the rear wheels axle (see; section 4.9.2, figure 27-A) ;

3- Insert the side tubing frame extension in the side tubing ; 4- Take a "Foot brake system assembly" and install it on the frame, using (2) two

7/16" key to tighten the (A) screws and (B) nuts

(see; figure 29) ;

5- Install the 12 inches rear wheel as same as a big radius rear wheel and follow the

instructions of section 4.9.1 depending of which type of axle used.

6- Remove the (2) two parking brakes of the big radius rear wheels (see; section 4.10)

using a 1/2" key.

NOTES:

1) There is no adjustment to do between the foot brake system assembly and the 12 inches rear wheel. Everything should be functional upon the final set up.

2) It will be not possible to install 12 inches rear wheels on a wheelchair equipped with a mid-wheel configuration.

3) On a wheelchair equipped with 12 inches rear wheels and antitippers, it will be not possible to have a foot brake system assembly installed.

4) It is possible to have 12 inches rear wheels with standard hand brake system (see; figure below).

4 SETUP INSTRUCTIONS

4.10 PARKING BRAKES

4.10.1 TO ADJUST THE POSITION OF THE PARKING BRAKE (Pushing or pulling brake type)

As per the level of wear of the tires or each time the position of the rear wheels was changed, an adjustment of the parking brakes is necessary.

a) Routine adjustment (see; figure 30) :

The effectiveness of the brake is optimum when a distance from 1/4 of an inch is obtained between the tire and the brake (when the brakes are disengaged).

To adjust this distance, use a 1/2" key to loosen the (A) screw then slide the support until you reach the needed position.

Figure 30 : Manual brake adjustment.

It is possible to have a pulling brake type which is activated in the opposite way of the standard brake. The adjustments explained in this section, can be apply to the pulling brake.

Disengage brake

Support

Apply brake

Support

Saddle

1/4"

4 SETUP INSTRUCTIONS

b) Adjustment according to the position of the rear 20, 22 or 24 inches wheels :

When the position of the rear wheels has been determined (section 4.9.2), the brake support should be repositioned (see; figure 31-A).

1. Loosen the (A) screw, using a 1/2" key. The (C) support can now slide in the tightening mechanism. NOTE

: The biggest shaft on the (C) support must be

placed upward as shown at figure 31-A ;

2. Loosen slightly the (B) screw, using a 13 mm key, this will allow the park ing brake tightening bracket, to slide on the biggest shaft of the (C) suppor t and the parking brake (D) to slide in the tightening bracket. NOTE: The parking brake ( D) support must be inverted as shown at figure 31-A ;

3. Tighten the entire assembly and make sure that when engaging the brake the movement is carried out without effort ;

4. Finish this adjustment as per section 4.10.1 a). NOTE: (A) screw on figure 30 section 4.10.1 a) is the same as (A) screw on the figure 31-A below.

Figure 31-A : Installation of the parking brake on its support (standard propulsion).

4 SETUP INSTRUCTIONS

Adjustment according to the position of the middle 20 or 22 inches wheels :

When the position of the middle wheels has been determined (section 4.9.3), the brake support should be repositioned (see; figure 31-B):

1. Loosen (A) screws and (B) nuts, using a 1/2" key ;

2. Slide the (D) support in the wheel axle tightening mechanism;

3. Loosen the (C) screw, using a 13 mm key, of the parking brake tightening bracket (E) to allow a double adjustment the one with the tightening bracket (E) on the biggest shaft of the (D) support and the one with the parking brake (F) in the tightening bracket (E). NOTE

: The biggest shaft on the (D) support must be

placed downward as shown at figure 31-B ;

4. Tighten the entire assembly and make sure that when engaging the brake the movement is carried out without effort ;

5. Finish this adjustment as per section 4.10.1 a).

Figure 31-B : Installation o f the parking brake on its supp or t (mid-wheel propulsion).

4 SETUP INSTRUCTIONS

c) Adjustment with a 12 inches rear wheel positions :

• The 12 inches rear wheel foot brake system assembly, is now activated either by foot or hand, directly behind the wheelchair by the caregiver. There is no need for adjustment.

NOTE : * The caregiver will have the choice of activation with the foot brake pedal or the two handles positioned on each side (see; figure 32).

Figure 32 : Caregiver using foot brake pedal.

USE THE FEET OR

THE HANDS

4 SETUP INSTRUCTIONS

4.10.2 TO CHANGE THE BRAKE LEVERS

You have the choice of two (2) types of brake extensions that can be assembled :

a) RETRACTABLE EXTENSION (see; figure 33-A) :

1. Install the extension guides (E) on each side of the brake lever (A) ;

2. Place the (D) spring include with (F) extension, in the (B) hole ;

3. Insert the (C) dowel pin in the (B) hole by compressing the (D) spring ;

4. While retaining the dowel pin (C) inside the (B) hole, slide the wheel brake extension (F) on the brake lever (A). Caution

: This assembly can be difficult to

do the first time, make sure you don't lose dowel pin (C).

Figure 33-A : Retractable extension installation.

4 SETUP INSTRUCTIONS

b) FIXED LENGTH EXTENSION (see; figure 33-B) :

1. Install the extension guides (C) on each side of the brake lever (A) ;

2. Insert the extension lever (E) on the brake lever (A) ;

3. Place the (D) screws in line with the (B) holes ;

NOTE

: If you have to drill a hole on the opposite side of the (B) hole, use a 7/64" drill.

4. Tighten (D) screws.

Figure 33-B : Fixed length extension installation.

4 SETUP INSTRUCTIONS

4.10.3 TO CHANGE THE ANGLE OF THE BRAKE LEVER (pushing brake type only)

NOTE

: The angle of the brake lever can be adjusted.

To do it :

1. Unscrew (B) screw, using a 3 mm Allen key and carry out a rotation of the lever until the needed position is reached ;

2. Replace (B) screw and tighten firmly.

Figure 34 : To change the angle of the brake lever.

LEVER

4 SETUP INSTRUCTIONS

4.11 ANTI-TIPPERS

4.11.1 HEIGHT ADJUSTMENT

Figure 35-A : Anti-tipper height adjustment.

Push the (B) spring release button and slip the lower part of the anti-tipper upwards or downwards to reach the height of 1 3/4 inches relatively to the floor. You can also use the (A) spring release button (see; figure 35-A, B and C).

The adjustments of your wheelchair must be made by a health care professional. Inadequate adjustments can cause wounds and/or damage to the user, the caregiver, the wheelchair or the environment.

A maximum of 1 3/4 inches between the floor and the antitippers must be maintained at any time.

4 SETUP INSTRUCTIONS

Figure 35-B : Always keep a distance of 1 3/4 inches between the anti-tippers and the floor.

Figure 35-C : Engage the spring release button in the adjustment holes.

If the seat to floor height or the dimension of the rear wheels were modified, the anti-tippers must be adjusted in order to maintain the height of 1 3/4 inches between the anti-tippers and the floor.

The anti-tippers must be well engaged and the spring release button must arise from the adjustment hole.

1 3/4"

4 SETUP INSTRUCTIONS

4.12 TILT MECHANISM

4.12.1 TO ADJUST THE FORCE REQUIRED TO TILT

We can adjust the force required to tilt. We simply have to position the anchor point of the pneumatic cylinder in either the front, center or rear position as shown on figure 36 below :

Figure 36 : Adjustment of the required force to tilt.

1. Using a 1/2" key, remove the screw that maintains the actuator base. Screws are under the seat on both left and right sides (see; figure 36).

Caution: Once the screws are removed on both sides, it will be really important to not touch the actuator handles, to keep both actuators in the same position from the start until the end of this modification.

2. Choose one of the (3) adjustment positions described on figure 36 and replace the screws in position. Tighten firmly.

3. Carry out some tilt tests to determine the required force so that the caregiver is able to tilt the user easily.

Center position;

this is the position at

delivery.

Front position;

+25% of force compared

to center position

required to activate the

tilt movement.

Rear position;

-25% of force

compared to center

position required to

activate the tilt

movement.

LEFT RIGHT

ACTUATOR

HEAD

5 OPERATING INSTRUCTIONS

5.1 «U» SHAPE REMOVABLE ARMREST

5.1.1 TO SWINGAWAY

1. To swingaway the armrest, push on the (A) release button in the same direction than the arrow and pull upwards the (E) transfer handle (see; figure 37).

2. To pos ition the armr est in driving mode, insert the (E) transfer handle in the (B) front socket armrest support and push down the armrest.

3. When the armrest is back into position, make sure that it is locked correctly in the (B) front socket armrest support. Try to lift the armrest by the (E) transfer handle, it should not move.

Figure 37 : Adjustable "U" shape armrest height.

5 OPERATING INSTRUCTIONS

5.1.2 TO REMOVE AND/OR INSTALL

1. Follow the 5.1.1 section to swingaway the armrest from its (B) front socket armrest support (see; figure 37).

2. Unscrew slightly the locking nut and the screw (G) from the (C) rear armrest socket, using a 8 mm key and a 4mm Allen key. Pull upwards the armrest, grabbing it by the (J) armrest upholstery to remove it completely from the (C) rear armrest socket.

3. To replac e the armrest, first insert the rear part of the armrest in the (C) rear armrest socket.

4. Tighten the lock ing screw and nut (G) and position the armrest as describe in the

5.1.1 section above.

5. After you put back in place the armrest, make sure that it is locked correctly and secure in the (B) front socket armrest support by trying to swingaway the armrest using the (E) transfer handle.

5.1.3 HEIGHT ADJUSTMENT

The

armrest allows a height adjustment by increment of 1 inch.

To do it (see; figure 37):

1. Unscrew slightly the locking nut and the screw (H) from the (F) armrest lateral panel, using a 8 mm key and a 4 mm Allen key.

2. Push on the (D) release button in the same direction than the arrow and pull upwards the armrest by grabbing the (J) armrest upholstery. Adjust the armrest height as needed. At every step of adjustment you should feel the (D) release button locking the armrest height in position. This will happen each time you will reach a new position.

3. Tighten the lock ing screw and nut (H) to fix permanently the armrest position.

It can be dangerous to raise the wheelchair, while holding it by the armrests.

5 OPERATING INSTRUCTIONS

5.2 ADJUSTABLE « T » SHAPE ARMREST

Figure 38-A : Telescopic armrest adjustment.

The height adjustment of the telescopic armrest is made by an up and down movement. This movement is activated by a lever positioned under the armrest towards rear (see; figure 38-A).

Figure 38-B : Lever to adjust height of the "T" shape armrest.

You should pull upwards the lever (see; figure 38-B) to adjust the armrest height as needed. Release the lever to block the armrest in position.

NOTE

: Once the armrest is adjusted, check if the mechanism is correctly secured in

position, by applying pressure on the armrest upwards or downwards.

LEVER

PULL

UPWARDS

5 OPERATING INSTRUCTIONS

5.3 FOOTREST / LEGREST

5.3.1 SWINGAWAY

1. To remove the footrests, you will first have to take your feet off the footplates;

2. Then by pushing on the (A) lever figure 39-B, the footrest will swingaway itself;

NOTE1 : It is preferable to fold back the footplate before to swingaway the footrest (see; figure 39-B).

NOTE2 : In some cases, because of the front wheels position it can be difficult to swingaway completely the footrest ;

NOTE3 : Always check that the front wheels are in driving mode position (see; figure 39-A).

Figure 39-A : To swingaway footrest/legrest.

DRIVING MODE POSITION

5 OPERATING INSTRUCTIONS

Figure 39-B : To swingaway footrest/legrest.

Figure 39-C : To swingaway footrest/legrest.

FOLD BACK

FOOTREST

5 OPERATING INSTRUCTIONS

5.3.2 TO REMOVE AND/OR INSTALL

• All the legrests on the

wheelchair are removable ;

1. To do this, it is initially necessary to swingaway the footrest as described earlier in section 5.3.1;

2. Then grab the legrest by its upper part, and raise it to release from the hanger bracket (C) (see; figures 39-B and C);

3. To replace in position the footrest, it is necessary to orient it at a 90

direction relatively to the seat and insert the footrest guide (B) in the hanger bracket (C) (see; figure 39-C);

4. Then, you will be able to swingaway the legrest to lock it in its original position. The blocking mechanism (D) must locked the (E) blocking system.

lt can be dangerous to raise the wheelchair, while holding it by the legrests.

5.3.3 TO RAISE OR LOWER THE LEGRESTS

a) To raise the legrests, it might be necessary to remove your foot from the

footplate and your legs from the calf pads; then grab the telescopic tubing (A) and pull upwards. The legrest will block itself in the needed position

(see; figure 40-A). b) To lower, push on the (B) lever while grabbing the telescopic tubing (A). You will

then be able to lower the legrest (see; figures 40-A and B).

Never put your fingers in the mechanisms when you proceed to either raise or lower the legrest. To raise or lower, always handle it by grabbing the telescopic tubing.

Figure 40-A : To raise or lower the legrests. Figure 40-B

5 OPERATING INSTRUCTIONS

5.3.4 RETRACTABLE FULL LENGTH LEGREST

Figure 41-A : Retractable full length legrest.

ASSISTED ELEVATION

The retractable full length legrest allows you to elevate the leg with assistance. To do this, you will need to push on the lever positioned on each side of the wheelchair (see; figure 41-B):

Figure 41-B : Retractable full length legrest elevation lever.

5 OPERATING INSTRUCTIONS

Figure 41-C : Retractable full length legrest elevated position.

RETRACTION

The retractable full length legrest can swingaway to help during a transfer. To swingaway the legrest, first lower the legrest to its lowest position and pull on the

lateral release switch (see; figure 41-D).

Figure 41-D : Lateral release switch allowing to swingaway the legrest.

5 OPERATING INSTRUCTIONS

The legrest will swing away under the seat creating space under the user's feet (see; figure 41-E).

Figure 41-E : Legrest swingaway to help movement during transfer.

To replace the legrest into position, push on the legrest extension tubing towards the calf pad. The legrest tubing will lock in position automatically (see; figure 41-E).

To put back the

legrest into

position.

Pull in the arrow's

direction.

5 OPERATING INSTRUCTIONS

5.4

BACKREST

5.4.1 TO FOLD THE BACKREST

In order to facilitate transportation of the

wheelchair, you can fold back the backrest on the seat. This operation will be possible only if nobody is on the seat.

To do this :

1. Remove rigid backrest, if necessary, or any other seating products that could prevent the backrest from being folded back ;

2. Position yourself behind the wheelchair and push on both folding backrest release handles at the same time (see; figure 42-A);

3. Keep pushing the folding backrest release handles and push on the stabilizer cross bar slowly towards the front (see; figure 42-B);

4. To replac e the backrest in the upright position, grab the backrest by the stabilizer cross bar (figure 42-B) and pull the backrest towards you. A mechanism will ensure that the backrest locks automatically.

Once the backrest will be back in upright position. Make sure that the mechanism is correctly locked, by pushing the backrest towards the front of the wheelchair.

NOTE : If your wheelchair is equipped with a gas actuator reclining backrest, you won’t be able to fold it back.

Figure 42-A : Folding backrest in upright position.

5 OPERATING INSTRUCTIONS

Figure 42-B : Folding backrest in reclined position.

5.4.2 RECLINING BACKREST

Figure 43 : Reclining backrest gas actuator handle.

To recline a gas actuator reclining backrest, you have to pull the handle positioned behind the backrest on the backrest handle structure (see; figure 43).

STABILIZER CROSS BAR

5 OPERATING INSTRUCTIONS

5.5 SEAT TILT MECHANISM

The

wheelchair is equipped with a seat tilt mechanism. This makes it

possible to tip over the seat, backward or forward.

• Before operating the tilt mechanism, make sure the parking brakes are applied (see; section 5.7.1).

NOTE: Make sure that the anti-tippers are in position and correctly adjusted (see; sections 4.11 and 5.8).

5.5.1 BACKWARD TIPPING

1. Position yourself behind the wheelchair and grab the tilt mechanism release handles (see; figure 44) ;

2. Exert and maintain a pressure on the two (2) release handles then tilt the seat backwards ;

3. Release the handles when the needed position is reached.

When you tilt the seat, in some configurations, the wheelchair becomes unstable. Carry out some tests before leaving alone a patient in a wheelchair whose seat has been tipped over.

4. When you wish to come back to the original seating position, proceeds the sam e way, but this time exert a light upwards pressure on the push handle while maintaining the release handles engaged.

5. Release the handles when the seat reaches the needed position.

5.5.2 FORWARD TIPPING

1. I t is initially necessary to release the limitation angle adjustment tubing (see;

section 4.6.3; figure 14). This tubing will block the seat in the horizontal position. When this tubing is in a disengaged position, the seat can be tipped over forward in order to help the user to stand up or transfer ;

Figure 44 : Seat tilt mechanism handles.

5 OPERATING INSTRUCTIONS

5.5.3 TILT WITH THE MOTORIZED TILT MECHANISM

1- Put the control box ON/OFF switch (A) to the ON position (see; figure 45-A).

2- The (B) light indicator panel will show you the batteries charge level (see; figure 45-B).

3- To tilt the seat forward, push the (C) toggle switch downward. 4- To tilt the seat backward, pull the (C) toggle switch upward. 5- The limitation of the tilt movement forward or backward will depend of the

electromagnetic cursors adjustment under the seat.

6- The GREEN light (D) gives you the information that you reach the

predetermine comfort zone.

Figure 45-A : Control box ON/OFF. Figure 45-B : Control box toggle switch.

It is recommended to recharge the batteries once the red lights on the (B) light indicator panel (figure 45-B) light up.

Never tilt the seat if the wheelchair is already on a slope surface.

A C

5 OPERATING INSTRUCTIONS

5.5.4 RECHARGING BATTERIES

• Always recharge the batteries in a ventilated area.

• Do not smoke near the charger during the battery charge.

• Do not remain in the wheelchair during charging.

Do not charge batteries in your bedroom. Charging, the batteries can release harmful gases for your health.

To recharge the motorized tilt mechanism batteries, you need to plug the charger in a wall outlet of 120 VDC. The wall outlet cable (D) is wound up in the cable winder placed just behind the backrest on the seat level (see; figure 46).

Figure 46 : Motorized tilt mechanism recharge.

5 OPERATING INSTRUCTIONS

NOTE: It will be possible for the user to check visually if the charger is in charge mode. As soon as the charger is plugged a red LED will light up and once the recharge will be done a green LED will light up (see; figure 47).

Figure 47 : Charger red and green LED.

If the green LED flashes just after you plugged the charger, it means that there is a battery connection problem or others. Contact a technical service center.

Red LED indicate that the

charger is under voltage.

Green LED indicate that the

recharge process is done.

5 OPERATING INSTRUCTIONS

5.6 REAR WHEELS

5.6.1 TO REMOVE AND/OR INSTALL

If your

wheelchair is equipped with a quick release axle, you can

remove wheels in order to facilitate transportation.

This operation is carried out when nobody is seated in the wheelchair.

To remove the wheel :

1. Push the (A) button and pull the wheel towards you while grabbing the wheel by its center (see; figure 48) ;

2. To replace, push the (A) button and insert the axle in the housing. Make sure that the axle is locked in position in the housing by the blocking pins (B).

Figure 48 : Quick release axle.

5.6.2 PNEUMATIC TIRE PRESSURE

In order to guarantee optimum performances from your wheelchair, the tire pressure must be checked every week.

6 x 1 ¼ inches Tire 35 psi 8 x 1 ¼ inches Tire 35 psi

20 inches Tire 65 psi 22 inches Tire 65 psi 24 inches Tire 65 psi

NOTE

: Make sure that the inflating apparatus will not damage the tire, if a higher

pressure than the one supported by the tire can be reached.

5 OPERATING INSTRUCTIONS

5.7 PARKING BRAKES

5.7.1 TO APPLY AND DISENGAGE THE PARKING BRAKE the PUSHING type

NOTE : With the PULLING brake type, invert the lever action.

Figure 49-A : Brake disengage.

Figure 49-B : Brake apply.

a) To apply the brake, exert a pressure on the handle towards front (see; figure 49-B) ; b) To disengage the brake, pull the handle towards you (see; figure 49-A).

NOTE : If the tire pressure is inadequate, the effectiveness of the brake is uncertain.

5.7.2 RETRACTABLE HANDLES

NOTE : In order to facilitate accessibility, the brake can be equipped with a retractable extension.

a) To use this extension, pull on the handle upwards (see; figure 50-A) ; b) Push back to retract (see; figure 50-B).

Figure 50-A : Retractable handle in extension. Figure 50-B : Retracted.

5 OPERATING INSTRUCTIONS

5.7.3 APPLY – DISENGAGE THE HILL HOLDER

In order to be able to climb slopes, your wheelchair can be equipped with a hill holder mechanism to stop backward movement when climbing.

Figure 51-A : Hill holder disengage. Figure 51-B : Hill holder apply.

1. To put the hill holder in function, lower the lever towards the ground (see; figure 51-B);

2. To disengage the hill holder, pull the lever upwards. The wheelchair is now free to move backward (see; figure 51-A).

When driving the wheelchair, hold your fingers distant from this mechanism.

LEVER

5 OPERATING INSTRUCTIONS

5.7.4 12 INCHES REAR WHEELS BRAKE

The 12 inches rear wheel foot brake system, is activated by the caregiver, behind the wheelchair, as shown in figure 52-A. There is no rear wheels adjustment.

To activate it, simply push with your foot on the central pedal, behind the wheelchair (see; figure 52-A).

Figure 52-A : Foot brake system, applied.

To deactivate it, simply push with your foot at the top of the central pedal or pull upwards the central pedal with your foot. You can also use your hand with one of the (2) two handles positioned on each side of the central pedal (see; figure 52-B).

Figure 52-B : Foot brake system, disengaged.

5 OPERATING INSTRUCTIONS

5.8 ANTI-TIPPERS

5.8.1 TO REMOVE

•

In order to facilitate the transportation of your wheelchair, the anti-tippers can be removed. To do this, exert a pressure on the (A) spring release button and remove the anti-tipper from its housing (see; figure 53-A).

5.8.2 TO SWINGAWAY

1. To go over some obstacles, the anti-tippers can be swingaway towards the inside of the frame (see; figure 53-A) ;

2. In this case, a third person must protect against any movements from behind t he wheelchair, near the backrest, both hands in contact with the backrest push handles.

Never use your wheelchair if the anti-tippers are not installed.

Figure 53-A : Anti-tippers adjustment.

5 OPERATING INSTRUCTIONS

5.8.3 TO REPLACE

1. To replace the anti-tippers, insert the tubing in its housing while pushing the spring release button. When the spring release button will catch itself in the hole, this will indicates that the anti-tipper is secured in position (see; figure 53-B) ;

2. Make sure that the anti-tippers are correctly locked in their hous ing. Try to turn or remove the anti-tippers, it should not be able to move.

Figure 53-B : To lock in position anti-tippers.

5 OPERATING INSTRUCTIONS

5.9 SEAT BELT

It is important for your comfort and safety that the belt provided with the wheelchair be adjusted to your size.

Never modify the assembly or anchor point of your belt..

In a paratransit transportation, the belt provided with your wheelchair, cannot be used as a seat belt. It is a restraint belt only.

To adjust the belt length, slip the strap in the plastic loop as represented in the next figure 54-A.

Figure 54-A : Seat belt length adjustment.

NOTE: The free part must always exceed at least three (3) inches from the plastic loop.

If you want to prevent the strap to slip from de plastic loop, pass the belt again in t he p las tic loop as shown on the figure below 54-B.

Figure 54-B : How to prevent seat belt adjustment modification.

5 OPERATING INSTRUCTIONS

5.10 TRANSPORTATION

5.10.1 ANCHOR POINTS POSITION

In order to immobilize your wheelchair during transportation, your wheelchair is equipped with four (4) anchor points. Two (2) are positioned at the front and tw o (2) at the rear (see; figure 55).

Figure 55 : Anchor points position for wheelchair transportation.

Always use these anchor points (see; figure 55) in a paratransit transportation.

NOTE

: If you remain seated in your wheelchair during transportation, it will be necessary to use a seat belt independent of your wheelchair. This one will generally be of the same type as those used in automobile vehicles.

5 OPERATING INSTRUCTIONS

5.10.2 ADVICE FOR TRANSPORTATION

•

Check that the brakes immobilize your wheelchair completely;

•

Put the reclining backrest in the upright position;

•

Reset the tilt mechanism in a horizontal position;

•

Put your seat belt on and make sure that it is well adjusted to your size. (Do not use the seat belt on your wheelchair only, use the one provided in the paratransit transportation).

•

Lower the legrest;

•

Always use your seat belt;

•

does not assume any responsibility as for the risks incurred by the use of the wheelchair as a seat in a public transport vehicle.

•

Your wheelchair is equipped with anchor points in the event of transportation. These anchor points cannot replace the approved restraint systems (seat belt) from Transport Canada;

•

Do not raise the wheelchair by its detachable components (armrests, footrests, etc...).

6 MAINTENANCE

Maintenance procedure

To function adequately and in a safe way, your wheelchair, like any other vehicle, needs care. A routine maintenance will increase the lifespan and the effectiveness of your wheelchair.

Once a year, bring your wheelchair at a qualified retailer or an authorized service center for an in-depth inspection and maintenance. A regular cleaning will reveal parts requiring adjustment or worn out.

Checked list

Initial adjustments must be made as per to your personal needs. For any subsequent maintenance, follow these procedures:

At delivery

Weekly

Monthly

Periodically

1. General The wheelchair drives in a straight line. It does not draw on one side.

x x

2. Brakes Must not interfere with the wheels when you drive, engage and disengage easily. The mobile points are neith er loose, nor worn.

x x

3. Cloth guard Check for deformation or protuberant parts. Make sure that all the fasteners are secured.

x x

4. Armrests Solid but easy to remove or swing away

x x

5. Armrest upholstery Check for tears – Make sure that the armrest upholstery is correctly fastened to the armrest.

x x

6. Seat fabrics and backrest Check for tears or depression.

7. Cable and release handle The cables do release completely and handles return to their original position after being released.

x x

8. Actuators for tilt or backrest Check for oil leakage.

x x

9. Rear wheels 20, 22 and 24 inches Make sure that the wheel bearings are in good condition and that the wheels are free of movement.

x x x

10. Handrims

Check for rough finish or peels. Make sure that they are correctly assembled to the wheels.

x x

11. Front wheels

Make sure that the tension is adequate while swiveling the wheel, it should stop gradually. Adjusts the tension on the bearing if the wheel stops abruptly.

CAUTION

The tires must be checked periodically for signs of wear and

tear and be replaced, if necessary.

x x

12. Tires

Check for wear. If pneumatic, check the air pressure.

x x

13. Axles

Keep the axles clean and oiled (3 in 1 oil)

14. Cleaning Clean and wax all parts – clean upholstery

6 MAINTENANCE

Tires pressure

Usually, recommended air pressure will be written on the side of the tire. However, if you cannot find it, you can refer to the following table.

6 x 1 ¼ inchesTire 35 psi

8 x 1 ¼ inches Tire 35 psi

20 inches Tire 65 psi

22 inches Tire 65 psi 24 inches Tire 65 psi

After having carried out an adjustment, make sure that all parts are well tightened BEFORE using the wheelchair. DO NOT tighten too much the hardware.

BREAKDOWN SERVICE GUIDE

7 BREAKDOWN SERVICE GUIDE

Wheelchair steers right

Wheelchair

steers left

Wheelchair is

difficult to

propulse

Loose front

wheel

Noise

SOLUTIONS

X X X

Check tires pressure.

X X X

Check screws and nuts tightening.

X X X

Make sure that both front wheels touch the ground simultaneously.

Check spokes tightening.

X X X X

Check front forks angle.

X X

Check the adjustment of the rear wheel axle (equal on both side).

X X X

Check the front and rear wheels bearing.

X X

Check the front and rear forks bearing.

8 WARRANTY

will warranty the

manual tilt wheelchair against any manufacturing defect for a period of one (1) year from the delivery date. This warranty covers all components and complementary, except the tires, tires tube and seat, backrest and armrests upholstery of which the warranty is (1) month.

will repair or replace any defective parts that will be returned carefully packed to prevent any further damage and send (paid port) to an authorized service center and this, during the warranty validity period.

However, this warranty does not apply to parts and components damaged by abuse, carelessness, accident and normal use or installed and modified by an unauthorized person.

guarantees the availability of components and parts necessary to the operation of the wheelchairs for a five (5) year period from the delivery date.

The present warranty is given in place of any other written, tacit or statutory warranty. The responsibility of

is limited to repair or the replacement of any parts or

components, according to the above-mentioned terms.

Exclusions and limitations

This warranty does not apply to products, which have been the subject of carelessness, accidental, normal use or abnormal use, maintenance or defective storage. Moreover, this warranty does not apply to products damaged in consequences of a repair, a component modification without the express assent of

neither with repairs

and/or modifications not carried out by an

authorized distributor and nor with

the products damaged because of circumstances independent of the will of This warranty is limited to repairs and, with absolute discretion of

to the replacement of defective parts as expressed with the present warranty. Except for the warranty expressed in this document,

does not grant, relative with its products, any warranty express or implicit, legal or conventional, including for hidden vice, nor no implicit warranty of marketable quality or suitability aiming at a particular use, except contrary stipulation with the present warranty.

The warranty stipulated above replaces any responsibility or obligation of concerning the damage coming from or referring to the

products.

8 WARRANTY

cannot, in any case, be held responsible for the particular, indirect or

consecutive damage, even if

were informed of the possibility of such damage. The warranty of the distributor is expressly limited to the repair and the replacement of non-conformity of products as envisaged in this warranty or to the refunding of a sum not exceeding the purchase price of the material in question.

The stipulations above constitute the complete and exclusive warranty declaration which applies to the

products and overrides any proposal or former agreement, orally or written, and on any other communication in between and a particular distributor relative to the

warranty.

does not assume any risk related to damages who could happen during

shipment.

do not grant any other warranty but that which is envisaged above. All the warranties, including the implicit warranty of marketable quality and suitability aiming at a particular use are limited to the period indicated above starting from the date of purchase.

cannot be held responsible for the particular, indirect or consecutive damage, from contractual nature, that result from an offence or another cause.

NOTES:

• Components exchanged under this warranty will be covered by the original warranty.

• If a component is returned to get its warranty enforced, but is considered by

as functional. The component will be returned to the customer.

AUTHORIZED SERVICE CENTRES

9 AUTHORIZED SERVICE CENTRES

Institut de réadaptation en déficience physique de Québec (Centre Cardinal-Villeneuve)

2975, chemin Saint-Louis Sainte Foy (Québec) G1W 1P9 Tél.: 418-529-9141

Institut de réadaptation en déficience physique de Québec (Centre François-Charron)

525, boulevard Hamel Québec (Québec) G1M 2S8 Tél.: 418-529-9141

Centre de réadaptation en déficience physique Carrefour de santé de Jonquière

2230, rue de l’Hopital CP 1200 Jonquière, QC, G7X 7X2 (418) 695-7787

Hôpital Sainte-Justine 3175, côte Sainte-Catherine

Montréal (Québec) H3T 1C5 Tél.: 514-345-4931

Institut de réadaptation de Montréal 6300, ave Darlington

Montréal (Québec) H3S 2J4 Tél.: 514-340-2080

Centre de réadaptation Lucie Bruneau 2275, ave Laurier Est

Montréal (Québec) H2H 2N8 Tél.: 514-527-4527

Centre hospitalier Hôtel-Dieu d’Amos

622, 4e rue Ouest Amos (Québec) J9T 2S2 Tél.: 819-732-3341 (2453) Sans frais : 1 800 875 7070

Centre de réadaptation La Maison 100, chemin Docteur-Lemay, C.P. 1055

Rouyn (Québec) J9X 5C8 Tél.: 819-762-6592

Centre régional de réadaptation La Ressource

135, boul. St-Raymond Gatineau, QC J8Y 6X7 Tél. : 819-777-8710

Centre de réadaptation Marie-Enfant de l’Hôpital Ste-Justine

5200, Bélanger Est Montréal (Québec) H1T 1C9 Tél.: 514-374-1710

Centre de réadaptation Le Bouclier

260, Lavaltrie Sud Joliette (Québec) J6E 5X7 Tél.: 1-800-363-2783 (450-755-2741)

Centre de réadaptation Le Bouclier

11, rue Boyer St-Jérome QC J7Z 2K5 Tél: (450) 432-7588

Centre de réadaptation Constance-Lethbridge

7005, De Maisonneuve Ouest Montréal (Québec) H4B 1T3 Tél.: 514-487-1770

AUTHORIZED SERVICE CENTRES

Centre de réadaptation de l’Estrie inc. 300, rue King Est, Bureau 200

Sherbrooke (Québec) J1G 1B1 Tél. : 819-346-8411

Centre de réadaptation Interval 4100, rue Jacques Labadie

Trois-Rivières (Québec) G9A 5M6 Tél. : 819-693-0441

Centre de réadaptation Gaspésie 230, route du Parc

Ste-Anne-des-Monts (Québec) G4V 2C4 Tél. : 418-763-3323

CSSS de la Mitis 800, ave du Sanatorium

Mont-Joli (Québec) G5H 3L6 Tél. : 418-775-7261

Centre de réadaptation l’Émergent (Sept-Îles)

450, rue Évangéline Sept-Îles (Québec) G4R 2N5 Tél. : 418-968-2470/800-968-2470

Centre de réadaptation l’Émergent (Baie-Comeau)

1250, rue Lestrat Baie-Comeau (Québec) G5C 1T8 Tél. : 418-589-2038

Service Orthaide

7, 9E Rue Rouyn Noranda, QC J9X 2A9 (819) 762-6592

Centre Montérégien de réadaptation

5300 Ch. de Chambly Saint Hubert, QC J3Y 3N7 (450) 676-7447 1-877-462-8638 1-800-667-4369

CRDP-CA

2055 Boul De La Rive-Sud bureau 100, Saint Romuald, QC G6W 2S5 (418) 834-5888

Customer service

2160, De Celles Québec (Québec) CANADA, G2C 1X8

Tel. : 1.800.463.5293

418.847.5225 Fax. : 418.847.7961

526-00040-00_Tango_2008-2011_D_ANG.doc

Orthofab Tango User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual