Orren Ellis W001740501 Assembly Instructions

Label Picture Description QTY

A

Top Panel

1

B

Bottom Panel

1

C

Right Center Panel

1

D

Left Center Panel

1

E

Right Side Panel

1

F

Left Side Panel

1

G

Right Door Panel

1

Caution : You must read this before you proceed

TV CABINET

Page 1 OF 10

H

Left Door Panel

1

I Leg 4

J

Metal Frame

1

K

Rear Panel

1

L

Shelf Panel

1

Label Picture Description QTY

①

Flat Washer Rings

(Big)

9

②

Bolt

(M8x20mm)

9

③ Spring Washer Rings

5

④

Flat Washer Rings

(Small)

5

⑤

Bolt

(M6x35mm)

5

⑥ Positioning Dowel

21

⑦

Cam Bolt

17

⑧

Cam Lock

17

⑨

Connector

4

Page 2 OF 10

⑩

Screw

(M3.5x12mm)

25

⑪

Drawer Handle

2

⑫

Bolt(M4x18mm) 5

⑬

Allen Key

(M8)

1

⑭

Allen Key

(M6)

1

⑮

Screwdriver

(not provided)

1

Before
Beginning
Assembly:

x4

x5

x5

x5

x21

x17

x17

x4

x25

x2

x5

x1

x1

x 9

x 9

Page 3 OF 10

Step 1

Overview

This TV Stand has multiple parts and may require up to 60 minutes to assemble.
To give you an overview of the TV Stand parts, the above picture is to help you put
the various parts into perspective. Please read through the instructions herebelow
to familiarise the parts and steps before assembly.

Take out all the Parts and Hardware, place them on a clean, non-marring surface.
Place the Metal Frame(J) bottom up.
Put Legs (I) to Metal Frame(J) using Flat Washer Rings(①) and Bolts(②) with
Allen Key(⑬).

Tighten all Bolts fully in a sequential manner.
Repeat the same process to attach the remaining Legs(I) to Metal Frame(J)

FRONT FACING

Top Panel(A)

Shelf Panel(L)

Drawer
Handle(⑪

）

Right Door
Panel(G)

Bottom Panel(B)

Leg(I)

Right
Center
Panel(C)

Rear Panel(K)

Left Center Panel(D)

Left Door Panel(H)

Metal Frame(J)

Left Side Panel(F)

Right Side Panel(E)

Page 4 OF 10

Step 2

Step 3
Step 4

Stand the Bottom Panel(B) up.
Attach Cam Bolts(⑦)to mounting positions on the Bottom Panel(B)with
Screwdriver(⑮)as pictured.
Insert Positioning Dowels(⑥)into mounting positions on the Bottom Panel(B)by
hand.

Attach Matel frame(J) to back of Bottom panel (B) with Spring Washer
Rings(③),Flat Washer Rings(④) and Bolts(⑤) using Allen Key(⑭).

Tighten the Bolts fully in a sequential manner.
Repeat the same process to attach the remaining ③.④and⑤

Page 5 OF 10

Step 5

Step 6

Step 7

Insert Positioning Dowels(⑥) from Shelf Panel(L) into mounting positions on Right
Center Panel(C) and Left Center Panel(D)

Insert Positioning Dowels(⑥) and Cam Bolt(⑦) from Bottom Panel(B) into
mounting positions on Right Side Panel(E).
Insert Cam Locks(⑧)on Right Side Panel(E) into the Bottom Panel(B)with
Screwdriver(⑮) until they "Lock". As shown in the picture.

Note: Ensure the arrow on Cam Lock head points towards the Cam Bolt
mounting position.

Repeat the same process to insert Left Side Panel(F) to Bottom Panel(B)

Insert Positioning Dowels(⑥) into mounting positions on the Shelf Panel(L)by
hand.

Step

Step

Page 6 OF 10

Step 8

Step 9

Step 10

Step7.1:
Insert Positioning Dowels(⑥) and Cam Bolt(⑦) from Bottom Panel(B) into
mounting positions on Right Center Panel(C) and Left Center Panel(D).
Insert cam Locks(⑧)on Right Center Panel(C) and Left Center Panel(D) into the
Bottom Panel(B) with Screwdriver(⑮) until they "Lock". As shown in the picture.

Note: Ensure the arrow on Cam Lock head points towards the Cam Bolt
mounting position.

Step7.2: Insert Positioning Dowels(⑥) into mounting positions on Right Center
Panel(C),Left Center Panel(D),Right Side Panel(E) and Left Side Panel(F)by hand
as picture.

Insert the Metal Frame(J) into the grooves on Right Side Panel(E),Left Side
Panel(F)and Bottom Panel(B).

Attach Cam Bolts(⑦) to mounting positions on Top Panel(A) with Screwdriver(⑮)
as picture.

Page 7 OF 10

Step 11

Step 12

Attach Connectors(⑨) to the mounting position on Right Door Panel(G) using
Screws(⑩) with Screwdriver(⑮) as pictured above.
Repeat same process to attach remaining Connectors(⑥) on Left Door Panel(H).

Tighten the Screws fully in a sequential manner.
Caution:There are lead mounting Position on Right Door Panel(G) and Left
Door Panel(H) to fix Connector.

Insert Positioning Dowels(⑥) from panels(C/D/E/F) into mounting positions on Top
Panel(A)
Turn the Cam Locks(⑧) and Cam bolts(⑦) clockwise with the Screwdriver(⑮) until
they all lock into place.

Note: Ensure the arrows on Cam Locks head points towards the Cam Bolt
mounting positions.
Tighten the Bolts fully in a sequential manner.

Attach Right Door Panel(G) with Connectors(⑨) to Right Side Panel(E) using
Screws(⑩) with Screwdriver(⑮)

12.1: First attach Connector(⑨) loosely using two Screws(⑩). Then make
adjustments until Connector is even. Add remaining Screws and tighten
completely.

12.2: Adjust the alignment of the Right Door Panel(G) and Right Side Panel(E) by
tightening the two middle screws on the Connector(⑨) until the Panels are flush.
Repeat same process to attach remaining Left Door Panel(H) on Left Side
Panel(F)

Note: There are pre-existing mounting positions on Door Panel(G) to fix the
Connectors(⑨).
Tighten the Screws fully in a sequential manner.

G

H

12.1: Adjust Connector to be

even

12.2: Adjust the alignment and

gap

Page 8 OF 10

Step 15
Step 16

Your TV Cabinet is ready for use.
This TV Cabinet can only be used on a flat, level surface.

Attach Handles(⑪) to Door Panel(G) with Bolts(⑫) using Screwdriver(⑮).

Tighten the Screws fully in a sequential manner.

Note: There are pre-existing mounting positions on Door Panel(G) to attach the
Handles(⑪).

Page 9 OF 10

Questions & Answers about Proposition 65

• What is Proposition 65?

Proposition 65 requires businesses to provide warnings to Californians about
significant exposures to chemicals that cause cancer, birth defects or other
reproductive harm. These chemicals can be in the products that Californians
purchase, in their homes or workplaces, or that are released into the environment.
By requiring that this information be provided, Proposition 65 enables Californians
to make informed decisions about their exposures to these chemicals.
Proposition 65 also prohibits California businesses from knowingly discharging
significant amounts of listed chemicals into sources of drinking water.
Proposition 65 requires California to publish a list of chemicals known to cause
cancer, birth defects or other reproductive harm. This list, which must be updated
at least once a year, has grown to include approximately 900 chemicals since it
was first published in 1987.

• What types of chemicals are on the Proposition 65 list?

The list contains a wide range of naturally occurring and synthetic chemicals that
include additives or ingredients in pesticides, common household products, food,
drugs, dyes, or solvents. Listed chemicals may also be used in manufacturing and
construction, or they may be byproducts of chemical processes, such as motor
vehicle exhaust.

• What does a warning mean?

If a warning is placed on a product label or posted or distributed at a workplace, a
business, or in rental housing, the business issuing the warning is aware or
believes that it is exposing individuals to one or more listed chemicals.
By law, a warning must be given for listed chemicals unless the exposure is low
enough to pose no significant risk of cancer or is significantly below levels
observed to cause birth defects or other reproductive harm.

• Where can I get more information on Proposition 65?

If you have specific questions on the administration or implementation of
Proposition 65, you can contact OEHHA's Proposition 65 program at
[e-mail], or by phone at [phone].

Page 10 OF 10