Page 1
Assembly Instruction
ToolsRequired:
LightSource:
CompatibleDimmerSwitches
EstimatedAssembly Time:
Preparation:
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Flatheadscrewdriver,Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Integrated12WLED
:LutronAYCL-153Por Lutron DVCL-153P.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Package Contents
12” Rod with Nipple
D
x2
Inner Backplate
A
x1
Mounting Screw
B
x4
STEP 1 Install Curve Tubes to Fixture Body-
A. Remove lock screws from the top of the Fixture Body (H). Attach the
Curve Tubes (G) onto the top of the Fixture Body (H) and align the
holes on the tabs of the Curve Tubes (G) to mounting holes on the
Fixture Body (H). Secure them together with lock screws previously
removed. Hand tighten until snug with screwdrivers.
6” Rod
C
x4
12” Rod
E
x2
Ceiling Canopy
F
x1
Curve Tubes
G
x1
Fixture Body
H
x1
STEP 2 - Install Ceiling Canopy, Rods and Fixture Body together
A. Determine the Rods (C/D/E) to be assembled to the Fixture Body (H)
according to your hanging height.
B. Pass the supply wires through the chosen rods (C/D/E). Thread the
Fixture Body (H) and the chosen Rods (C/D/E) together. Hand
tighten until snug.
C. Remove swivels from the bottom of the Ceiling Canopy (F) by
unlocking hex nuts inside of the Ceiling Canopy (F) .
D. Pass supply wires through one swivel, the Ceiling Canopy (F), one
lock washer, the lanyard and one hex nut in turn.
E. Thread swivels onto the upper rods. Make sure swivels are in the
same direction before hand tighten them until snug.
F. Place the Ceiling Canopy (F), lock washers, lanyard and ground wire
back onto swivels as shown. Secure them together with hex nuts.
Tight gently until snug.
Suggested rods for Ceiling height :
8’ ceiling : use (1) 6” rod and (2) 12” rods
9’ ceiling : use (2) 6” rods and (2) 12” rods
Hex Nut
Lock Washer
Ground Wire
Lock Washer
F
Hex Nut
Lanyard
Lock Washer
Ceiling Canopy
Swivel
(Same Direction)
C
Hole
Lock Screw
Mounting Hole
G
Figure 1
Figure 2
H
H
Thank you for purchasinga product.
1of2
C
D
E
Supply Wires
Page 2
STEP 3 Install Inner Backplate and Fixture Body-
A. Pass the supply wires and ground wire through the Inner Backplate
(A). Attach the Inner Backplate (A) to Outlet Box with the head of
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug.
Outlet Box
Figure 3
A
Outlet Box Screw
(not supplied)
STEP 4 - Attach Lanyard
A. The purpose of the lanyard is to provide the installer a means to
support the fixture from the junction box while connecting the
electrical wires. This enables the fixture to hang from the junction
box and your hands are free to make the wire connections.
B. Turn the Button Stop so it may be inserted into the Inner Backplate
slot. Make sure the Button Stop is completely inside the Inner
Backplate (A). Slowly release the fixture to make sure it is
supported by the Button Stop. Proceed to the wiring steps in the
next step. Once you are complete with the wiring there is nothing to
do with Lanyard. The Lanyard will push into the junction box when
the fixture is placed for final mounting.
STEP 5 Make Wire Connections-
A. bare or green
Wrap ground wire around green ground screw on the
inner backplate, no less than 2 in from the end of the wire.
Tighten .
the green ground screw
ches
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Green Ground Screw
on the Inner Backplate
White wire
from fixture
Black wire
from fixture
Ground wire
from Fixture
Figure 5
STEP 6 Install Fixture Body-
A. Attach the Ceiling Canopy (F) and the Fixture Body (H) over the
Inner Backplate (A) and secure with Mounting Screws (B). Tighten
until snug with screwdrivers.
Your fixture is now assembled and ready to use. Enjoy!
Figure 4
FINISH: BRUSHED NICKEL
Slot
A
Button Stop
Lanyard
F
B
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
7.75”
6.75”
A
F
Figure 6
5.75”
4.75”
39.25”
Thank you for purchasinga product.
2of2
6.25”
3”
Loading...