Page 1
WARNING: DISCONNECT POWER AT THE MAIN
FUSE BOX BEFORE INSTALLATION.
WARNING:
This xture is intended for installation in
accordance with the National Electrical Code
(NEC) and all local code specications. If you are
not familiar with code requirements, installation
by a certied electrician is recommended.
Before assembly, remove all parts and part
packages from box. If anything is missing, please
contact the retailer from which the product was
purchased.
1. Hold mounting bracket (A) so tabs on mounting
bracket (A) are on the top and bottom and
facing out.
2. Place mounting bracket over junction box. Align
holes in mounting bracket with holes in junction
box. While holding mounting bracket in correct
position, mark with a pencil on the wall the
location of each hole in each side of mounting
bracket. Set bracket aside while installing
anchors.
3. Using a drill bit the appropriate size for the
included wall anchor (G), drill a hole at each
marked location on wall.
4. Using hammer, carefully tap one wall anchor (G)
into each hole. Lip of anchor (G) should be ush
with wall.
5. Hold mounting bracket (A) so tabs on mounting
bracket (A) are on the top and bottom and
facing out.
6. Carefully pull house wires out of junction box
and pass house wires through large center hole
in mounting bracket (A).
7. Align holes in the center of mounting bracket
(A) with holes in junction box. Align holes
in corners of mounting bracket (A) with wall
anchors (G).
8. Thread each junction box screw (B) into holes in
center of mounting bracket (A) and into holes in
junction box. DO NOT fully tighten.
9. Thread each wall anchor screw (H) into each hole
in corners of mounting bracket (A).
10. Fully tighten junction box screws (B) and wall
anchor screws (H) to attach mounting bracket
(A) to junction box.
CAUTION: Ensure house wires are pulled completely
through hole in mounting bracket. DO NOT pinch
wires between mounting bracket and wall.
ANY QUESTIONS CALL: 800-613-3261
M-F 8:00AM-6:00PM ET
ITEM#: BV714-10-15
G
JUNCTION
BOX
A
G
B
TAB
H
TAB
H
B
1
elkhome.com
Page 2
ITEM#: BV714-10-15
11. Strip 3/4” of insulation from ends of xture
wires.
12. Slightly loosen ground screw on mounting
bracket (A). Do not completely remove ground
screw. Wrap house ground wire (copper)
around ground screw, leaving enough ground
wire to attach to xture ground wire. Twist
end of xture ground wire and end of house
ground wire together. Twist wire connector (C)
onto ends of wires. Completely tighten wire
connector (C). Reference chart below for correct
wire connections.
Connect Supply (House) Ground Copper Wire to:
Bare Copper Wire or,
Bare Silver Wire or,
Green Insulated Wire.
13. Twist end of house lead wire (black) and end of
xture lead wire together. Twist wire connector
(C) onto ends of wires. Completely tighten
wire connector (C). Twist end of house neutral
wire (white) and end of xture neutral wire
together. Twist wire connector (C) onto ends of
wires. Completely tighten wire connector (C).
Reference chart to the right for correct wire
connections.
14. Wrap electrical tape (not included) around wire
connectors (C) and wires. Ensure wires are
securely fastened into wire connectors.
15. Carefully push all wires and wire connectors into
junction box.
A
GROUND
SCREW
HOUSE
GROUND
WIRE
(COPPER)
Connect Black Lead
Supply (House) Wire to:
Black Wire or,
*Parallel Cord
(Round and Smooth) or,
No printed words on
wire insulation or,
Insulated Wire
(other than green)
with Copper Conductor.
*When parallel wire (SPT 1 & SPT 2) is used:
The lead wire is round in shape or smooth.
The neutral wire is square in shape or ridged.
FIXTURE LEAD WIRE HOUSE LEAD WIRE
FIXTURE GROUND
WIRE
FIXTURE NEUTRAL
WIRE
C
FIXTURE
GROUND
WIRE
Connect White Neutral
Supply (House) Wire to:
White Wire or,
*Parallel Cord
(Square and Ridged) or,
Printed words on
wire insulation or,
Insulated Wire
(other than green)
with Silver Conductor.
(BLACK)
HOUSE GROUND
WIRE (COPPER)
HOUSE NEUTRAL WIRE
(WHITE)
16. Place backplate (D) over mounting bracket (A).
Pass holes in backplate (D) over ends of xture
mounting screws (E) on mounting bracket (A).
CAUTION: Do not pinch wires between backplate
and wall.
17. Screw one threaded cap (F) onto end of each
xture mounting screw (E). Tighten threaded
caps (F) to secure xture to wall.
18. CAUTION: DO NOT touch bulb with bare hands.
Oils from skin can damage bulb. Carefully insert
bulb (included) into socket. Each end of socket
is spring-loaded. Carefully push bulb towards
the end you just inserted and t other end of
bulb into other end of socket. WARNING: DO
NOT exceed maximum bulb wattage.
19. Install bulb cover (L) over each bulb.
20. From top of xture, carefully lower one glass
panel (K) down over each bulb. Fit sides of glass
panel behind tabs on backplate (D).
K
D
A
E
L
F
TAB
F
2
elkhome.com
Loading...