Page 1
INSTALLATION INSTRUCTION
958 - LED Pendant
PD-95820
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
A B C D E
Wire Connector
Qty: 3 pcs +1 Extra
7EAC112201
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
G0
Junction Box Screw
Qty: 2 pcs + 1 Extra
7MPF0415C2
#8-32x9/16 SS
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Mounting Screw
7MPF0412S1(CH)
7MPF0412S1BK(BK)
4MPF0412S2W5(WT )
5/32-32x5/16
Nickel/BK/WT
Qty: 1 Extra
Wood Screw
Qty: 3pcs+1 Extra
7MPF2204J2
Ø4x22
Nickel Plating
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Plastic Anchor
Qty: 3pcs+1 Extra
7TDD082401
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
Page 2
INSTALLATION INSTRUCTION
958 - LED Pendant
PD-95820
White Wire
Black Wire
A
Wire Connector
E
Plastic Anchor
D
Wood Screw
Junction Box
Bare Copper Ground Wire
Mounting Back Plate
B
Junction Box Screw
Purple - Dim +
Gray - Dim -
Mounting Ring Dimensions
C
Cable-gripper
Push up
Mounting Screw
Driver
Lamp Body
3 3/8"
Ø
8 1/8"
1 3/4"
1 3/8"
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (C) from the xture.
4. Drill holes in the wall aligned with the key holes located in the mounting back plate, insert the plastic anchor (E).
5. Secure back plate to the junction box using junction box screws (B), fasten it to the wall using wood screw (D).The side of the mounting
plate marked “GND” must face out.
6. Adjust the xture wire length by pushing the cable gripper on the canopy and pulling the wire as desired.
7. Connect the driver input wires with junction box wires as shown in Fig.2, making sure that all wire connectors (A) are secured. If your outlet
box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to
the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
8. This xture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specic dimming wires
information.
9. Place the xture over the back plate and secure it with mounting screws (C)
NOTE: DIMMING WIRING INFORMATION (Fig. 3)
• To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).
• To utilize 0-10V dimming: use wire purple (dim+), gray (dim-), black (hot), white (neutral) and bare copper ground wire (ground).
Fig. 2 Wiring
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Black - Hot
White - Neutral
Fig.3
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Purple - Dim+
Gray - Dim-
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
G0
2
Loading...