Page 1
INSTALLATION INSTRUCTION
LED Bath
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
A1 B1 C1 D1 E1 F1 G1
Wire Connector
Qty: 3 pcs +1 Extra
7EAC112201
Junction Box Screw
Qty: 2 pcs +1 Extra
7MPF0415C2
Plastic Anchor
Qty: 2 pcs +1 Extra
7TDD082401
Wood Screw
Qty: 2 pcs +1 Extra
7MPF2204J2
Silicon Gasket
Qty: 2 pcs +1 Extra
7TGD181001CL
Knurled Nut
Qty: 2 pcs +1 Extra
4MPM1010F1BN
Screw
Qty: 2 Extra
7MPF0412S1
1
Page 2
INSTALLATION INSTRUCTION
LED Bath
FIG.1
Inner Glass
Wood Screw
G1
Screw
D1
E1
Outer Glass
Mounting Plate
A1
F1
Knurled Nut
Silicon Gasket
Ground Wire
B1
Junction Box Screw
Wire
Connector
Junction Box
C1
Plastic Anchor
Mounting Plate Dimensions
5 1/8"
1 3/8"
2 1/2"
4"
5 7/8"
8 1/8"
Ø
3 1/2"
Ø
2 3/4"
1 3/4"
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the screw (G1) from the xture.
4. Insert the outer glass into the xture, secure it with knurled nut (F1) and silicon gasket (E1).
5. Drill a hole in the wall aligned with the key holes located in the mounting plate, insert the plastic anchor (C1).
6. Secure the mounting plate to the junction box using junction box screws (B1),
fasten it to the wall using wood screw (D1). The side of the mounting back
plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
7. Connect the xture wires to junction box wires as shown in Fig. 2, making
sure that all wire connectors (A1) are secured. If your outlet box has a green
or bare copper ground wire, connect the xture’s ground wire to it.
Otherwise, connect the xture’s ground wire directly to the back plate
using the green screw provided.
8. Secure the xture to the mounting plate using screw (G1).
Fig. 2 Wiring
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
2
Loading...