Orren Ellis ORLS1296 Installation Instruction

INSTALLATION INSTRUCTION

Vanities & Wall Sconce

WARNING

IMPORTANT: NEVER attempt any work without shutting o the electricity.

- Read all instructions before installing.

- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.

- Place the wall switch in the “OFF” position.

CAUTION

- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

MISE EN GARDE

- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.

ADVERTENCIA

IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.

- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.

- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.

- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).

- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN

- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.

HARDWARE

A1 G1F1E1D1C1B1

Wire Connector

Qty: 5 pcs

Mounting Screw

Qty: 1 Extra

Junction Box Screw
Qty: 2 pcs + 1 Extra

Mounting Ring

Qty: 1 pc

Conversion Plate

Qty: 1 pc

Assembly Screw

Qty: 2 pcs + 1 Extra

Driver

Qty: 1 pc

1

INSTALLATION INSTRUCTION

Vanities & Wall Sconce

FIG. 1 MOUNT ON SWITCH

Fixture

Mounting Plate

Driver

G1

Mounting Screw

B1

Wire Connector

A1

Adjustable Nut

Junction Box Screw

FIG. 2 MOUNT ON JUNCTION BOX

Assembly Screw

F1

C1

Mounting Plate

Conversion Plate

E1

Junction Box Screw

C1

D1

Mounting Ring

Driver

G1

Switch Box

Junction Box

FIG. 3

Wire

Fixture Backplate

Adjustable Nut

Mounting Screw

B1

Back Plate Dimensions

5 1/2”

1 5/8”

1 3/8”

2 3/8”

2

INSTALLATION INSTRUCTION

Vanities & Wall Sconce

PREPARATION

1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.

2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

INSTALLATION
MOUNT ON SWITCH BOX (Fig. 1)

3. Remove the mounting screw (B1) from the xture.

4. Connect the driver (G1) input wire to switch box wires as shown in Fig. 4, making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare cooper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground
wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.

*Requires Driver to be recessed within the switch box.

5. Secure the mounting plate to the switch box using the junction box screw (C1). The side of the mounting plate marked “GND” must face out.

6. The back plate location for this xture is adjustable. First loosen both adjustable nuts by turning counterclockwise. Second adjust the
back plate to your desired location. Third, pull and tighten the electrical wire. Lastly, secure the back plate by turning both adjustable
nuts clockwise.

7. Place the xture over the mounting plate, and secure it with mounting screw (B1).

OR

MOUNT ON JUNCTION BOX (Fig. 2)

3. Remove the mounting screw (B1) from the xture.

4. Connect the driver (G1) input wire to junction box wires as shown in Fig. 4, making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare cooper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground
wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.

*Requires driver to be recessed within the junction box.

5. Secure the mounting ring to the junction box using the junction box screw (C1). Make sure the two holes (Spacing 2-3/4”) are horizontal as
shown in Fig. 2. The side of the mounting plate marked “GND” must face out.

6. Secure the mounting plate and conversion plate to the mounting ring with assembly screw (F1).

7. The back plate location for this xture is adjustable. First loosen both adjustable nuts by turning counterclockwise. Second adjust the
back plate to your desired location. Third, pull and tighten the electrical wire. Lastly, secure the back plate by turning both adjustable
nuts clockwise.

8. Place the xture over the mounting plate, and secure it with mounting screw (B1).

Fig. 4 Wiring

Fixture Wires

Black or
Smooth

Fixture Wires

White or
Ribbed

Fixture Wires

Bare wire
(Ground)

House Wires

Black
(Hot)

House Wires

White
(Neutral)

House Wires

Green or Bare Copper
(Ground)

3

INSTALLATION INSTRUCTION

Vanities & Wall Sconce

WARNING

IMPORTANT: NEVER attempt any work without shutting o the electricity.

- Read all instructions before installing.

- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”

the circuit breaker switch(es) that control the power to the xture or room that you are working on.

- Place the wall switch in the “OFF” position.

CAUTION

- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are

worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les

règlements locaux.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt

(« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

MISE EN GARDE

- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté

et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.

ADVERTENCIA

IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.

- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta

lámpara.

- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.

- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación

principal en la posición “OFF” (APAGADO).

- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN

- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni

utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.

HARDWARE

A1 G1F1E1D1C1B1

Wire Connector

Qty: 5 pcs

Mounting Screw

Qty: 1 Extra

Junction Box Screw
Qty: 2 pcs + 1 Extra

Mounting Ring

Qty: 1 pc

Conversion Plate

Qty: 1 pc

Assembly Screw

Qty: 2 pcs + 1 Extra

Driver

Qty: 1 pc

1

INSTALLATION INSTRUCTION

Vanities & Wall Sconce

FIG. 1 MOUNT ON SWITCH

Mounting Screw

B1

Fixture

Mounting Plate

Driver

G1

Wire Connector

A1

Adjustable Nut

Junction Box Screw

FIG. 2 MOUNT ON JUNCTION BOX

Assembly Screw

F1

C1

Mounting Plate

Conversion Plate

E1

Junction Box Screw

C1

D1

Mounting Ring

Driver

G1

Switch Box

Junction Box

FIG. 3

Wire

Mounting Screw

B1

Fixture Backplate

Adjustable Nut

Back Plate Dimensions

5 7/8”

1 5/8”

1 3/8”

2 1/2”

2

INSTALLATION INSTRUCTION

Vanities & Wall Sconce

PREPARATION

1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.

2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

INSTALLATION
MOUNT ON SWITCH BOX (Fig. 1)

3. Remove the mounting screw (B1) from the xture.

4. Connect the driver (G1) input wire to switch box wires as shown in Fig. 4, making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare cooper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground
wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.

*Requires Driver to be recessed within the switch box.

5. Secure the mounting plate to the switch box using the junction box screw (C1). The side of the mounting plate marked “GND” must face out.

6. The back plate location for this xture is adjustable. First loosen both adjustable nuts by turning counterclockwise. Second adjust the
back plate to your desired location. Third, pull and tighten the electrical wire. Lastly, secure the back plate by turning both adjustable
nuts clockwise.

7. Place the xture over the mounting plate, and secure it with mounting screw (B1).

OR

MOUNT ON JUNCTION BOX (Fig. 2)

3. Remove the mounting screw (B1) from the xture.

4. Connect the driver (G1) input wire to junction box wires as shown in Fig. 4, making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare cooper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground
wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.

*Requires driver to be recessed within the junction box.

5. Secure the mounting ring to the junction box using the junction box screw (C1). Make sure the two holes (Spacing 2-3/4”) are horizontal as
shown in Fig. 2. The side of the mounting plate marked “GND” must face out.

6. Secure the mounting plate and conversion plate to the mounting ring with assembly screw (F1).

7. The back plate location for this xture is adjustable. First loosen both adjustable nuts by turning counterclockwise. Second adjust the
back plate to your desired location. Third, pull and tighten the electrical wire. Lastly, secure the back plate by turning both adjustable
nuts clockwise.

8. Place the xture over the mounting plate, and secure it with mounting screw (B1).

Fig. 4 Wiring

Fixture Wires

Black or
Smooth

Fixture Wires

White or
Ribbed

Fixture Wires

Bare wire
(Ground)

House Wires

Black
(Hot)

House Wires

White
(Neutral)

House Wires

Green or Bare Copper
(Ground)

3