Page 1
4 PIECE OUTDOOR PATIO CONVERSATION SET WITH PILLOW SET
Thank you for purchasing the CHAIR!
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
Hardware:
Component:
1
A
B
D
Bolt x 8
Flat Washer x 8
Allen Wrench x 1
Chair Back x1
1
2
Left Leg x1
2
Page 1 of 3
4
Right Leg x1
3
3
4
Seat Frame x1
Page 2
STEP 1:
Put Chair Back (1) upside down on a carpeted or padded area as shown.
Attach Left Leg (2) to Chair Back (1) by using 1 piece of Bolt (A) with 1 piece of Flat Washer (B) as shown.
Use Allen Wrench (C) to tighten Bolt (A).
Repeat the same steps for Right Leg (3).
Do not fully tighten Bolts (A) at this step.
1
2
C
A
B
Ax2 Bx2 Cx1
STEP 2:
Attach Seat Frame (4) to Chair Back (1), Left Leg (2), and Right Leg (3) by using 6 pieces of Bolt (A) with 6 pieces of
Flat Washer (B) through the bottom of Seat Frame (2) as shown.
Use Allen Wrench (C) to tighten all the Bolts (A) clockwise until secure.
A
B
3
Hardware & Tool required
Ax6 Bx6 Cx1
Page 2 of 3
C
1
2 3
A
B
A
B
4
B
A
A
B
Hardware & Tool required
Page 3
STEP 3:
Carefully turn over the assembled chair as shown.
Assembly is completed. The chair is ready to enjoy now!
Page 3 of 3
Page 4
Thank you for purchasing the LOVESEAT!
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the loveseat, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
Component:
Hardware:
A
B
D
1
Bolt x 8
Flat Washer x 8
Allen Wrench x 1
Loveseat Back x1
1
2
Left Leg x1
2
Page 1 of 3
4
Right Leg x1
3
3
4
Seat Frame x2
Page 5
STEP 1:
Put Loveseat Back (1) upside down on a carpeted or padded area as shown.
Attach Left Leg (2) to Loveseat Back (1) by using 1 piece of Bolt (A) with 1 piece of Flat Washer (B) as shown.
Use Allen Wrench (C) to tighten Bolt (A).
Repeat the same steps for Right Leg (3).
Do not fully tighten Bolts (A) at this step.
1
2
3
C
A
B
Ax2 Bx2 Cx1
STEP 2:
Attach Seat Frame (4) to Loveseat Back (1), Left Leg (2), and Right Leg (3) by using 6 pieces of Bolt (A) with 6 pieces of
Flat Washer (B) through the bottom of Seat Frame (2) as shown.
Use Allen Wrench (C) to tighten all the Bolts (A) clockwise until secure.
A
B
Hardware & Tool required
2
B
Ax6 Bx6 Cx1
Page 2 of 3
C
A
B
1
A
B
3
4
B A
A
Hardware & Tool required
Page 6
STEP 3:
Carefully turn over the assembled loveseat as shown.
Assembly is completed. The loveseat is ready to enjoy now!
Page 3 of 3
Page 7
Thank you for purchasing the TABLE!
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the table, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
Component:
Hardware:
A
B
D
1
Bolt x 12
Flat Washer x 12
Allen Wrench x 1
Table Top x1
1
2
3
2
Leg x2
2
Page 1 of 3
3
Apron Frame x2
Page 8
STEP 1:
Put Table Top (1) upside down on a carpeted or padded area as shown.
Attach 1 piece of Leg (2) to bottom of the Table Top (1) by using 1 piece of Bolt (A) with 1 piece of Flat Washer (B) as shown.
Use Allen Wrench (C) to tighten Bolts (A).
Repeat the same steps for the remaining 1 piece of Leg (2).
C
A
B
2
2
1
Ax4 Bx4 Cx1
STEP 2:
Place 1 piece of Apron Frame (3) to the assembled Legs (2) as shown.
Attach by using 4 pieces of Bolt (A) with 4 pieces of Flat Washer (B) to each end of Apron Frame (3) as shown.
Use Allen Wrench (C) to tighten Bolts (A) clockwise until secure.
Repeat the same steps for the remaining 1 piece of Apron Frame (3) to the assembled Legs (2).
Hardware & Tool required
C
A
B
3
2
Ax8 Bx8 Cx1
Page 2 of 3
2
3
Hardware & Tool required
Page 9
STEP 3:
Carefully turn over the assembled table as shown.
Assembly is completed. The table is ready to enjoy now!
Page 3 of 3
Loading...