Assembly Instructions
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
EASY
DIFFICULT
Page 1 of 7
Tools Required for Assembly:
Allen Wrench
(Included)
Phillips Screwdriver
(Not Included)
MD
Before you begin, please read Page 3
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
Parts List
#1 x 1 pc x 2
Backrest w/Legs
#2 x 1 pc x 2
Seat
#3 x 1 pc x 2
Right Front Leg
#4 x 1 pc x 2
Left Front Leg
Hardware List
#A x 2 pcs x 2
Bolt 5/16”x1-3/4”
#B x 4 pcs x 2
Bolt 5/16”x2”
#C x 4 pcs x 2
Bolt 5/16”x3-1/4”
#D x 10 pcs x 2
Flat W asher
#5 x 1 pc x 2
Front Leg Support
#6 x 1 pc x 2
Right Leg Support
#7 x 1 pc x 2
Left Leg Support
Note: The above parts and hardware are shown
for a complete assembly of ONE chair.
However, the actual parts and hardware (with an
exception of the Allen wrench) in the box will be
twice the quantities listed to include the
assembly of the second chair.
#E x 10 pcs x 2
Lock W asher
#F x 1 pc
Allen Wrench
#G x 1 pc x 2
Wood Dowel
#H x 6 pcs x 2
Wood Screw
Insert the front leg support (#5) into the right
front leg (#3) and the left front leg (#4).
Note: Right and left are determined by facing the
front of the chair in the upright position.
#B x 4 pcs
#D x 4 pcs
#E x 4 pcs
#G x 1 pc
I. Place the seat (#2) facing down on a
protected surface. Insert a wood
dowel (#G) into the center hole of
the seat (#2).
II. Align the assembled front legs with
the pre-drilled holes of the seat (#2).
III. Prepare 4 bolt assemblies by
inserting FIRST the lock washer (#E)
onto the bolt (#B) and then the flat
washer (#D) onto the SAME bolt
(#B), in that order .
IV. Insert the bolt assembly through the
corner holes of the seat (#2) and
secure those bolts using the Allen
wrench (#F) to lock them with the
right front leg (#3) and the left front
leg (#4).
#4
#3
Turn right (clockwise) to tighten
#3
#6
#4
#7
#A x 2 pcs
#D x 2 pcs
#E x 2 pcs
Turn right (clockwise) to tighten
I. Insert the right leg support
(#6) into the right front leg
(#3) and insert the left leg
support (#7) into the left front
leg (#4).
II. Align the backrest with legs
(#1) with the wood dowel (#G)
and the other ends of the leg
supports.
III. Prepare 2 bolt assemblies by
inserting FIRST the lock
washer (#E) onto the bolt (#A)
and then the flat washer (#D)
onto the SAME bolt (#A), in
that order.
IV. Insert the bolt assemblies
through the holes near the
wood dowel (#G) of the seat
(#2) and secure those bolts
using the Allen wrench (#F) to
lock them with the backrest
with legs (#1).
#C x 4 pcs
#D x 4 pcs
#E x 4 pcs
I. Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#E) onto the bolt (#C) and then the flat washer (#D) onto the
SAME bolt (#C), in that order.
II. Insert the bolt assemblies through the corner holes of the seat
(#2) and secure those bolts using the Allen wrench (#F) to lock
them with the backrest with legs (#1).
Turn right (clockwise) to tighten
#H x 6 pcs
Secure all the leg supports with 6 wood
screws (#H) using a Phillips screwdriver
to lock them with the backrest with legs
(#1), the right front leg (#3) and the left
front leg (#4).
#3
Turn right (clockwise) to tighten
#4
Carefully place the completed chair in the upright position. Make sure
the chair is rested on a flat surface and does not feel loose or wobbly .
If it does, double check that the bolts/screws are secured and properly
tightened.
ASSEMBLE EVERYTHING EXACTLY THE SAME FOR THE SECOND CHAIR
Page 7 of 7
Loading...