Orpak Systems 819539370 Users Manual

No. 817439300

Revision D3

WWGGTT OOuuttddoooorr UUnniitt -- MMaannuuaall

INSTALLATION

SAFETY CONSIDERATIONS

Read all warning notes and instructions carefully. They are included to help you installing the Product safely
in the highly flammable environment of the fuel station. Disregarding these warning notes and instructions
could result in serious injury or property damage. It is the installer responsibility to install, operate and
maintain the equipment according to the instructions given in this manual, and to conform to all applicable
codes, regulations and safety measures. Failure to do so could void all warranties associated with this
equipment.

Remember that the fuel station environment is highly flammable and combustible. Therefore, make sure
that actual installation is performed by experienced personnel, licensed to perform work in fuel station and at
a flammable environment, according to the local regulations and relevant standards.

WARNING - EXPLOSION HAZARD

Install the Product only in the non-hazardous area of the fuel station.
Use standard test equipment only in the non- hazardous area of the fuel station, and approved test equipment
for the hazardous areas.
In the installation and maintenance of the Product, comply with all applicable requirements of the National
Fire Protection Association NFPA-30 “Flammable and Combustible Liquids Code”, NFPA-30A “Automotive
and Marine Service Station Code”, NFPA-70 “National Electric Code”, federal, state and local codes and any
other applicable safety codes and regulations.
Do not perform metal work in a hazardous area. Sparks generated by drilling, tapping and other metal work
operations could ignite fuel vapors and flammable liquids, resulting in death, serious personal injury,
property loss and damage to you and other persons.

CAUTION - SHOCK HAZARD

Dangerous AC voltages that could cause death or serious personal injury are used to power the Product.
Always disconnect power before starting any work. The Product has more than one power supply connection
port. Disconnect all power before servicing.

WARNING – PASSING VEHICLES

When working in any open area of fuel station, beware of passing vehicles that could hit you. Block off the
work area to protect yourself and other persons. Use safety cones or other signaling devices.

CAUTION

Do not attempt to make any repair on the printed circuit boards residing in the Product, as this will void all
warranties related to this equipment.

PROPRIETY NOTICE

This document contains propriety and confidential information. It is the property of ORPAK SYSTEMS
Ltd. It may not be disclosed or reproduced in whole or in part without written consent of ORPAK
SYSTEMS. The information in this document is current as of the date of its publication, but is subject to
change without notice.

WGT Outdoor Manual

i

DISCLAIMER

This document is provided for reference only. Although every effort has been made to ensure correctness,
ORPAK SYSTEMS does not guarantee that there are no errors or omissions in this document.

FCC COMPLIANCE STATEMENT IN USER'S MANUAL

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

Sample user information for a Class A digital device:

THE FCC WANTS YOU TO KNOW:

This equipment has been tested and found to comply with the limits

or a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment.

his equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual,

ay cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his

FCC Warning

Modifications not expressly approved by the manufacturer responsible could void

the user’s authority to operate the equipment under FCC rules.

Sample user information for a Class B digital device

ii

WGT Outdoor Manual

THE FCC WANTS YOU TO KNOW:

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential area.

This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation.

if this equipment does not cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of

the following measures:

 Reorient or relocate the receiving antenna

 Increase the separation between the equipment and the receiver

 Connect the equipment to an outlet on a circuit different from that

to which the receiver is connected



Consult the dealer or an experienced radio/TV technician

FCC Warning

Modifications not expressly approved by the manufacturer responsible

could void the user’s authority to operate the equipment under FCC rules.

This document is the property of:
ORPAK SYSTEMS Ltd.
ISRAEL

WGT Outdoor Manual

iii

TABLE OF CONTENTS

Paragraph Page

SECTION 1

GENERAL DESCRIPTION ..........................................................1-1

1-1. WGT – WIRELESS GATEWAY TERMINAL .................................................................. 1-1

1-2. WGT OUTDOOR BOX ............................................................................................... 1-1

1-3. INSTALLATION OPTIONS ............................................................................................... 1-2

1-4. INSTALLATION REQUIREMENTS ................................................................................. 1-2

1-5. INTERNAL POWER SUPPLY ........................................................................................... 1-2

1-6. EXTERNAL POWER SUPPLY .......................................................................................... 1-3

1-7. INSTALLATION LOCATION ........................................................................................... 1-4

1-8. INSTALLATION INSTRUCTIONS ................................................................................... 1-4

11--88..11.. IINNSSTTAALLLLAATTIIOONN ((WWIITTHH IINNTTEERRNNAALL PPOOWWEERR SSUUPPPPLLYY)
11--88..22.. IINNSSTTAALLLLAATTIIOONN ((EEXXTTEERRNNAALL PPOOWWEERR SSUUPPPPLLYY)
11--88..33.. WWIIRRIINNGG aanndd LLEEDDSS DDEESSCCRRIIPPTTIIOON
11--88..44.. BBAATTTTEERRYY RREEPPLLAACCEEMMEENNT

T ............................................................................................. 1-12

N .................................................................................. 1-10

) .........................................................1-8

)............................................... 1-5

1-9. WGT OUTDOOR BOX SPECIFICATIONS (WITH POWER SUPPLY) .........................1-13

1-10. WGT OUTDOOR BOX SPECIFICATIONS (NO POWER SUPPLY).............................. 1-14

1-11. TROUBLESHOOTING 1-15

LIST OF ILLUSTRATIONS

Figure Page

Figure 1-1. WGT - General View 1-1
Figure 1-2. WGT – with Internal Power Supply 1-2
Figure 1-3. WGT – with External Power Supply 1-3
Figure 1-4. WGT, Outdoor Installation Control Drawing 1-4
Figure 1-5. WGT Outdoor Box, Inside View 1-5
Figure 1-6. Terminal Block – Internal View 1-6
Figure 1-7. Gland Holes - General View 1-6
Figure 1-8. WGT Box Cable Installation 1-7
Figure 1-9.WGT - Cover Removed 1-8
Figure 1-10.WGT External Connections 1-9
Figure 1-11. WGT Glands 1-9
Figure 1-12. PCB Battery 1-13
Figure 1-13. WGT Outdoor Box Dimensions 1-15

iv

WGT Outdoor Manual

LIST OF TABLES

Table Page

Table 1-1. WGT Board Input Power Pin Assignment 1-10
Table 1-2. RS485 Communication CN12 Pin Assignment 1-10
Table 1-3. CN2 Pin Number Assignment, LAN Communication 1-11
Table 1-4. CN11 Pin Assignment - RS232 Communication 1-11
Table 1-5. Jumpers (Factory default) 1-11
Table 1-6. Indication LEDs on the Left side of PCB (left to right) 1-11
Table 1-7. Indication LEDs on the Right side of PCB (left to right) 1-12
Table 1-1. WGT, Troubleshooting Procedures 1-16

WGT Outdoor Manual

v