Orisec CK-10, CT-10, CP-10, CK-20, CT-20 User Manual

...

Master User Guide

CK-10, CT-10, CP-10, CK-20, CT-20, CP-20,

CP-30, CP-50, CP-100 & CP-200

Designed and Manufactured

in the United Kingdom

Contents

1. About your Security System .............................................................................................. 4

Introduction ............................................................................................................................................. 4

About this Manual ................................................................................................................................. 4

Alarm Transmission System ................................................................................................................ 4

Zones and Areas .................................................................................................................................... 4

Access code ............................................................................................................................................. 4

NFC Tags .................................................................................................................................................. 5

Keypads ..................................................................................................................................................... 5

Emergency Keys ..................................................................................................................................... 8

2. Operating your Security System ...................................................................................... 11

Introduction ............................................................................................................................................ 11

User Menu ............................................................................................................................................... 11

Before Arming the Security System ................................................................................................ 11

Full Arming Your Security System .................................................................................................. 12

Part Arming your Security System .................................................................................................. 13

Disarming your security system ...................................................................................................... 14

Area full arming .................................................................................................................................... 15

Area part arming .................................................................................................................................. 16

Area disarming ..................................................................................................................................... 17

Resetting after an alarm .................................................................................................................... 18

Resetting after a Fault Condition .................................................................................................... 19

Omitting Zones.....................................................................................................................................20

Changing Your Code .......................................................................................................................... 21

Turn chime on/off ................................................................................................................................22

System Event Logs ...............................................................................................................................23

View event log ......................................................................................................................................24

View mandatory log ............................................................................................................................24

View chime log .....................................................................................................................................25

Print Log .................................................................................................................................................25

System Tests .......................................................................................................................................... 31

Test Bell & Strobe ................................................................................................................................32

Walk Test Zones ...................................................................................................................................33

View Inactive Zones ............................................................................................................................34

View Zone Status .................................................................................................................................35

View Module Status ............................................................................................................................36

Do a Test Call ........................................................................................................................................ 37

Review Voice Messages ..................................................................................................................... 37

Send SMS Message .............................................................................................................................38

Change Settings ...................................................................................................................................39

Set Time & Date ...................................................................................................................................40

Holiday Dates ........................................................................................................................................40

Add/Delete Users ................................................................................................................................. 41

Alter chime zones ................................................................................................................................46

Coms Modules ......................................................................................................................................47

About .......................................................................................................................................................49

3. Additional Features ........................................................................................................... 50

4. Troubleshooting ................................................................................................................. 51

5. Touch-Tone Remote Control .......................................................................................... 52

Introduction ...........................................................................................................................................52

Remote Control Menu .......................................................................................................................52

Remote Access .....................................................................................................................................52

Full Arm ...................................................................................................................................................53

Part Arm ..................................................................................................................................................53

Disarm .....................................................................................................................................................53

Turn Remote Controlled Outputs On and Off ...........................................................................54

Record and Playback Speech Messages ......................................................................................54

Installer Information ............................................................................................................................55

1. About your Security System

Introduction

Your security system is made up of several component parts comprising of a control panel, one or more remote keypads, external sounder and various detection devices that are connected to either the control panel or zone expansion modules. The control panel houses the system’s electronics and stand-by battery and is normally installed out of sight in a utility room or under stairs cupboard etc.

The remote keypad provides the user interface for the system and is used to send commands to the system and to display the current system status via a graphic display. The remote keypad also provides audible feedback annunciation of fault and alarm tones. Remote keypads are normally mounted in convenient locations inside the protected premises, near to the points of entry and exit.

Please read this manual carefully and have your installer instruct you on your system’s

operation. Become familiar with the features that have been implemented on your system. All users of this system should be equally instructed in its use.

About this Manual

This manual provides a thorough explanation of all system functions that are available to the master user, including basic system operation, user code programming, remote control and troubleshooting.

Alarm Transmission System

Your security system may be fitted with an automatic alarm transmission system, which will communicate alarms, faults and other events to a 24hr manned Alarm Receiving Centre (ARC). If you accidently cause a false alarm activation, immediately call the ARC to prevent an unnecessary emergency response.

Zones and Areas

A zone is an input that is normally used to monitor a single detection device like a motion detector, door contact or shock sensor etc. An area is one or more zones grouped together to allow independent arming and disarming of areas.

Access code

As a user of the security system, you will be assigned a 4, 5 or 6 digit access code. Access codes are used to arm and disarm the system. Some access codes can perform additional system functions, such as programming system options, omitting zones and performing system tests.

Your access code may not allow you to access certain system functions. For instance, if your code is only allowed to arm the system you will not be able to disarm the system, once the system is armed.

NFC Tags

NFC tags can be assigned to users of the system. The tag behaves just like an access code when presented to the NFC reader built into the keypad. NFC technology is built into credit cards, bank cards, smart phones and other devices. (Not on CK-10 or CT-10)

Keypads

One or more remote keypads will be installed throughout the protected premises, usually close to the entry and exit door. The CK-10, CK-20, CT-10, and CT-20 control panels have built in keypads.

Keypad Layout: RK-400-LCD & RK-450-LCD

1. LCD display

2. NFC reader – present your NFC tag in this area (not on CK-10 or CT-10)

3. Status Icons

4. Keyboard – see below

Keyed Keypad buttons

Actions

Arm system and to navigate upwards in the menu

Part arm system and to navigate down in the menu

Chime tone selection and can be used to enter menu

Omit zones and if held for 1 second can work to go ‘back’ in a menu

If held for 1 second can be used to toggle options and outputs

✓

Selection button

Cancel Button. Press and hold for 1 second to delete a selection.

Keypad Layout: CK-10, CK-20, RK-500, RK-550, MK-700 & RK-700

1. LCD display

2. NFC reader – present your NFC tag in this area (not on CK-10 or CT-10)

3. Status Icons

4. System status LED

5. Ambient light sensor – used automatically adjusts the keyboard and LCD backlight level

6. Keyboard – see below

Keyed Keypad buttons

Actions

Arm system

Part arm system

Area arm system

Selection button

Chime tone selection

Escape button

Cancel button

Touchscreen Keypad Layout: CT-10, CT-20, TK-650

1. Full colour touch display

2. NFC Reader – present your NFC tag in this area (not on CK-10 or CT-10)

3. Status Icons

4. System status LED

Touch Keypad buttons

Function

Arm system

Part arm system

Area arm system

Selection button

Chime tone selection

Escape button

Cancel button

Status Icons

The system status area on the display is used to show the following information:

Status Icon

Indicates

#$%K

Battery is charging / is charged

Mains power is connected

Mains power is disconnected

External strobe is flashing

External bell is sounding

Chime is enabled

Wi-Fi module connected

GSM module connected

Ethernet module connected

Phone line connected

User programmed timer running

[

User programmed alarm running

Status LED

The keypad has a single multi-colour LED and is used to indicate the following:

Colour

System Status

Blue

Normal operation, all zones are healthy

Green

User menu selected and system is ready for arming

Yellow

One or more zones are active, system may not arm

Red

Alarm active

Emergency Keys

The keypad provides three different emergency functions. Depending on the setup of your system, activation from these keys can alert the local police, key holders and security personal via your Alarm Receiving Centre (ARC).

The emergency keys for each keypad can be individual enabled or disabled and may

not be enabled on your installation due to local standards and police requirements.

The Panic alarm (Police) function for each keypad can be programmed for either an audible or silent operation.

Keyed Keypad Emergency Keys

To activate the emergency functions, press together the keys shown below for a duration of 1 second:

Emergency Alarm

Keys

Fire

Press 1 & 3

Panic Alarm (PA)

Press 4 & 6

Medical

Press 7 & 9

Touch Keypad Emergency Keys

1. To activate the emergency keys on your touch screen keypad you will need to be on the

Home screen:

2. From the top part of the screen select one of the emergency functions, for example ‘Fire’:

3. You will then be prompted to press the Fire Alarm icon, and then select the icon again

to confirm the activation. This is in place to ensure it is a confirmed event and not an accidental button press:

4. Press the ‘CONFIRM’ icon to generate the selected emergency or press the ‘Back’ icon

to cancel.

2. Operating your Security System

Introduction

Before attempting to operate your security system, please ensure that you have familiarised yourself with the procedures covered in this section of the manual.

User Menu

On entering a valid access code or presentation of a tag, the keypad will display the ‘User Menu’. This menu is used to perform all system operations including arming, disarming, testing

and system configuration.

Before Arming the Security System

Before attempting to arm your security system, ensure that all protected areas are secure by closing any doors and windows etc. If the system is not ready for arming the keypads show the zones that are active (if enabled by your installer) and the keypad status LED will illuminate in yellow:

If your system has the ‘Global Keypad Information” option enable by your installer, the

keypad will show zone status information for all zones. If the option is disabled, the keypad will only show zones status information for zones that are assigned to the same area as the keypad.

Full Arming Your Security System

The full arming mode is used for protecting all detection zones within your allocated areas and is normally used when leaving the premises or area unoccupied. Before attempting to full arm, check that your areas are ready for arming. To full arm your area(s), please proceed as follows:

1. Enter code or present tag to select the user menu.

2. From the user menu, use the U/ u and D/ p keys to scroll to Full arm

system’:

3. Press E or k to full arm, the exit tone will start and the keypad will instruct you to

exit the protected area:

4. The keypad will then indicate that the system is Fully Armed.

Part Arming your Security System

The part arming mode only protects predefined detection zones. The system has 3 ‘Part arm’ modes which allows for flexible arming configurations, e.g., ‘Part arm 1’ could be configured to

arm only downstairs zones, whereas ‘Part arm 2’ could be configured to arm only perimeter

zones. To part arm your area(s), please proceed as follows:

1. Enter code or present tag to select the user menu.

2. From the user menu, use the U/ u and D/ p keys to scroll to ‘Part arm

1’:

3. Use the L/ o and R/ r keys to change the part arm mode (1, 2 or 3), then

press E or k to part arm.

4. The exit tone will start and the keypad will instruct you to exit the protected area:

5. The keypad will then indicate that the system is part armed:

Part arm settings will be pre-programmed by your installation company.

Disarming your security system

When the system or area is armed, you must enter the protected area via the designated entry route. Upon entering the premises, the entry timer and entry tone will start. To successfully disarm the alarm, a valid access code or tag must be entered before the entry timer expires. To disarm your area(s), please proceed as follows:

1. Enter the protected area by the designated entry point, the entry tone will sound and

the keypad will show the following screen:

2. Enter your code or present tag, the entry tone will silence and the keypad screen will

indicate that the system has just been disarmed:

3. After a short delay the keypad will then return to normal operation:

Area full arming

Zones can be grouped together to make ‘area sets’. Area sets are often used in multi tenanted

buildings where there is a communal entrance and separate living spaces/areas of work. Users can arm individual or multiple area sets. To full arm selected areas, please proceed as follows:

1. Enter code or present tag to select the user menu.

2. From the user menu, use the U/ u and D/ p keys to scroll to ‘Area full

arm’:

3. Press E or k to select, the ‘arm areas’ menu is now displayed:

` Area will be armed a Area will remain unarmed

4. Use the U/ u and D/ p keys to select the ‘Area’. Then use the L/ o

and R/ r keys to toggle the selected area on or off. Once you have selected the areas that you would like to arm, press E or k to confirm.

5. The exit tone will start and the keypad will instruct you to exit the protected area:

6. The keypad will then indicate that the areas that are fully armed:

Area part arming

Zones can be grouped together to make ‘Area Sets’. Area Sets are often used in multi tenanted

houses where there is a communal entrance and separate living spaces. Users can arm individual or multiple area sets. To part arm selected areas, please proceed as follows:

1. Enter your code or present tag to select the user menu.

2. From the user menu, use the U/ u and D/ p keys to scroll to ‘Area part

arm 1’:

3. Use the L/ o and R/ r keys to change the part arm mode (1, 2 or 3), then

press E or k to select, the ‘part arm areas’ menu is now displayed:

` Area will be part armed a Area will remain unarmed

4. Use the U/ u and D/ p keys to select the ‘Area’. Then use the L/ o

and R/ r keys to toggle the selected area on or off. Once you have selected the areas that you would like to part arm, press E or k to confirm.

5. The exit tone will start and the keypad will instruct you to exit the protected area:

6. The keypad will then indicate that the areas that are part armed:

Part arm settings will be pre-programmed by your installation company.

Area disarming

Normally when entering a protected area via the designated entry route, the area is disarmed after a valid access code or tag presentation. Sometimes it is desirable to disarm one or more areas before entering them via the designated entry route. To disarm your selected areas, please proceed as follows:

1. The keypad will show the areas that are currently full armed:

2. Enter your code or present tag, the ‘disarm areas’ menu is displayed:

` Area will be disarmed. a Area will remain armed.

3. Use the U/ u and D/ p keys to select the ‘Area’. Then use the L/ o

and R/ r keys to toggle the selected area on or off. Once you have selected the areas that you would like to disarm, press E or k to confirm.

4. The selected areas are disarmed and the keypad displays any areas that have remained

armed:

+ 39 hidden pages

Orisec CK-10, CT-10, CP-10, CK-20, CT-20 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual