Orion Technology LA750 User Manual

17" TFT LCD Monitor

MODEL No. : N7LT

1 INSTRUCTION MANUAL

CONTENTS

SAFETY INSTRUCTION 2

CAUTIONS 4

FCC RF INTERFERENCE STATEMENT 5

CONNECTING WITH EXTERNAL EQUIPMENT 6

RESOLUTION 8

CONTROLS AND FUNCTIONS 9

REMOTE FUNCTIONS 19

REAR VIEW 21

STAND SLOPE 22

D-SUB CONNECTOR PIN ASSIGNMENTS 23

POWER MANAGEMENT 24

SPECIFICATIONS 25

TROUBLESHOOTING GUIDE 26

WICHTIGE HINWEISE (GERMAN) 27

This Monitor was
Manufactured by ISO 9001
Certified Factory

INSTRUCTION MANUAL 2

SAFETY INSTRUCTION

1. Read all of these instructions.

2. Save these instructions for later use.

3. Follow all warnings and instructions marked on the product.

4. Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

5. Do not use this product near water.

6. Do not place this product on an unstable cart, stand or table.
The product may fall, causing serious damage to the product.

7. Slots and openings in the cabinet and the back are provided for
ventilation: to ensure reliable operation of the product, these openings
must not be blocked by placing the product on a bed, sofa, rug or
other similar surface.
This product should never be placed near or over a heat register.
This product should not be placed in a built-in installation unless proper ventilation
is provided.

8. This product should be operated from the type of power source indicated on the
marking label. If you are not sure of the type of power available, consult your dealer
or local power company.

9. This product is equipped with a 3 wire grounding type plug having a third(grounding)
pin. This is a safety feature. If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet. Do not defeat the purpose of
the grounding-type plug.

10. Do not allow anything to rest on the power cord.

Do not locate this product where persons will walk on the cord.

11. If an extension cord is used with this product, make sure that the total of the

ampere ratings on the products plugged into the extension cord do not exceed the
extension cord ampere rating. Also, make sure that the total of all products
plugged into the wall outlet does not exceed 10 amperes.

12. Never push objects of any kind into this product through cabinet slots as they may

touch dangerous voltage points or short out parts that could result in a risk of fire
or electric shock. Never spill any kind of liquid on the product.

13. Do not attempt to service this product yourself, as opening or removing covers

may expose you to dangerous voltage points or other risks.
Refer all servicing to service personnel.

3 INSTRUCTION MANUAL

SAFETY INSTRUCTION

14. Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions.

A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the Product does not operate normally when the operating instructions are

followed. Adjust only those controls that are covered by the operating
instructions since improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore normal

operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance, indicating a need for

service.

CCAAUUTTIIOON

N

The power supply cord is used as the main disconnect device, ensure that the
socket-outlet is located/installed near the equipment and is easily accessible.

AATTTTEENNTTIIOON

N

Le cordon d`alimentation est utillsé comme interrupteur général. La prise de
courant doit être située ou installée à proximité du matériel et être facile
d`accès

CAUTION TO SERVICE PERSONNEL

POWER SUPPLY CORD IS USED AS MAIN POWER DISCONNECT DEVICE IN
THIS PRODUCT. UNPLUG THIS PRODUCT FROM THE WALL OUTLET
BEFORE REMOVING THE BACK COVER AND SERVICING

EMISSION CHARACTERISTICS TESTED BY SEMKO

THIS PRODUCT HAS BEEN TESTED AND HAS SHOWN COMPLIANCE WITH
THE NATIONAL SPECIFICATIONS SUCH AS SWEDISH MPR 1990.10.(MPR

)

INSTRUCTION MANUAL 4

CAUTIONS

NEVER REMOVE THE BACK COVER

Removal of the back cover should be carried out only by qualified personnel.

DO NOT USE IN HOSTILE ENVIRONMENTS

To prevent shock or fire hazard, do not expose the unit to rain or moisture.
This unit is designed to be used in the office or home. Do not subject the unit to
vibrations, dust of corrosive gases.

KEEP IN A WELL VENTILATED PLACE

Ventilation holes are provided on the cabinet to prevent the temperature from
rising.
Do not cover the unit or place anything on the top of unit.

AVOID HEAT

Avoid placing the unit in direct sunshine or near a heating appliance.

TO ELIMINATE EYE FATIGUE

Do not use the unit against a bright back ground and where sunlight or other light
sources will shine directly on the monitor.

BE CAREFUL OF HEAVY OBJECT

Neither the monitor itself nor any other heavy object should rest on the power cord.
Damage to a power cord can cause fire or electrical shock.

5 INSTRUCTION MANUAL

FCC RF
INTERFERENCE STATEMENT

NNOOTTEE:

:

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.

This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television
reception which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures.

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

- Consult the dealer or an experienced radio, TV technician for help.

- Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not

expressly approved by the grantee or manufacturer could void the users
authority to operate such equipment.

DOC COMPLIANCE NOTICE

This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the radio interference regulation of Canadian
Department of Communications.

AVIS DE CONFORMATION AU MDC(DOC)

Le presént appareil numérique n`émet pas de bruits radio-électriques dépassant les
limites appliqués aux appareils numériques de Class B d´arès les règlement sur le
brouillage radio-électrique conçuent par le ministère des communications du
Canada.

INSTRUCTION MANUAL 6

CONNECTING WITH EXTERNAL
EQUIPMENT

CCAAUUTTIIOON

N

Be sure to turn off the power of your computer before connecting the monitor.

1. CONNECT THE VIDEO SIGNAL CABLE

A. Connect one end of the signal cable to the back panel of the monitor

and connect the other end to the graphic card on back of the computer.

B. Secure the connection with the screws on the plug.

2. CONNECT THE POWER CORD

Connect the female end of the power cord to the power input

receptacle on the LCD Monitor.

Then, plug the male end of the power cord to an AC outlet or computer.

3. CONNECT THE A/V CABLE

A. Connect the end of RCA(Yellow, White, Red) SCART or S-VHS cable to

the terminals on the back of the Monitor.

B. Connect an antenna or CATV cable to the terminal on the back of the Monitor.

(Optional TV Tuner can be purchased from the dealer)

C. Connect one end of stereo audio cable to the stereo jack on the back of the Monitor.

(Connect another end of stereo audio cable to the “Audio(Line) out” terminal of

the sound card on your computer or another audio equipment)

D. Headphone may be connected to the headphone jack(option) on the left-hand side

of the Monitor.(While Headphone is connected, the sound from the built-in speaker

will be disabled)

4. TURN THIS MONITOR ON AND START YOUR SYSTEM

7 INSTRUCTION MANUAL

5. CONNECT THE TUNER(OPTION)

IINNSSTTRRUUCCTTIIOON

N

Be sure to turn off the power of your monitor before connecting the tuner.

A. Open the cover.
B. Insert the Tuner and close the cover.

CCCAAUUTTIIOON

N

A. Do not disassemble the tuner after proper Installation.

B. Do not pull the antenna terminal only. This terminal is easy to break.

CONNECTING WITH EXTERNAL
EQUIPMENT

640 350 31.5 70
720 400 31.5 70
640 480 31.5 60
640 480 37.5 75
640 480 35.0 67
800 600 37.8 60

800 600 46.8 75
1024 768 48.3 60
1024 768 60.0 75
1280 1024 63.9 60
1280 1024 80.0 75

INSTRUCTION MANUAL 8

RESOLUTION

This monitor is a digitally-controlled multi-frequency monitor.
It operates at horizontal frequencies of 31 to 80KHz and vertical
frequencies of 56 to 75Hz.

Because of its micro processor-based designs, it offers auto-synchronization
and auto-sizing capabilities. This monitor offers 11 programmed settings
as listed in the table below and designed its best quality at 1280X1024, 64KHz@60Hz.

Sometimes, displayed image quality couldn’t be good enough in other modes
because of TFT-LCD Monitor’s basic characteristics.
To enjoy the best quality, change the mode; click the right mouse botton
anywhere on the desktop

“Properties” “Settings”, and applies the resolution to

1280X1024. Click the “Advanced” button, change “Refresh rate” to 60Hz.
These 11 preset modes cover most of the common video modes supported by

popular graphic adaptors. However, each adaptors implementation of these
video modes may vary slightly in timings. You may find it necessary to make
minor adjustments to the display settings (i.e., horizontal position) using
the On Screen Display. For further information and instructions on using
the On Screen Display, please refer to “Controls and Functions.”

RESOLUTION FREQUENCY

H(Pixels) V(Lines) H(KHz) V(Hz)

PRESET MODES

VGA

MAC

VESA