Orion Power Systems Office Pro UPS1000VA, Office Pro UPS1500VA User Manual
192321942005001
Office Pro UPS1000VA/1500VA Users Manual
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS –
This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries.
CAUTION-
- Intended for installation in a controlle d environment.
- Maximum ambient temperature 95°F.
- Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions. Keep unauthorized
personnel away from battery.
- To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum branch circuit overcurrent protection in accordance with the National
Electric Code, ANSI/NFPA.
SETUP
1 Inspection
Inspect the UPS upon receipt. Notify the carrier and
dealer if there is damage. The package is
recyclable; save it for reuse or dispose of it properly.
2 Placement
5 RJ11/RJ45 Connector
(Optional) Provide an RJ11/RJ45 connector to
extend the connection of telecommunication/network
cable.
IN OUT
3 Check the Site Wiring
Fault Indicator
Caution: If the site wiring fault indicator lights, get a
qualified electric ian to correct the building wiring.
6 Connect Computer
Interface Port
(Optional) Connect the optional interface cable to
the USB interface port on the back of the UPS.
Connect to the computer. See software
documentation for installation instruction.
4 Connect the loads
First, connect the UPS to the AC input power
source. Next, plug your computer, monitor, or other
devices into the receptacles on the rear of the UPS.
To use the UPS as a master “On/Off” switch, make
sure that all of the connected devices are switched
“On”.
Caution: To prevent an overloading condition, do
not connect a laser printer to the backup outlets.
These UPS outlets provide battery power to the
connected equipment when utility voltage is outside
acceptable limits.
7 Operation Test
1. Connect the UPS to the wall receptacle.
2. Press the Power button on the front panel, verify
that the Green Line ( ) LED is on.
3. Connect your computer equipment to the
receptacles on the back of the UPS. Unplug the
input power cable of the UPS from the wall
receptacle to check if the Line ( ) and
Inverter( ) LED are flashing every 2 seconds.
Verify that the audible alarm is beeping.
4. The ups is now running on internal battery to
support the connected equipment.
5. Reconnect the ups to the wall receptacle to
complete the test. The audible alarm will silence
and the Green Line LED will be visible.
6. IMPORTANT: Plug the UPS into the wall outlet
to charge the internal battery for a minimum of 8
hours prior to using the UPS.
7. STORAGE:
Store at -15 to +30 °C (+5 to +86 °F), charge the
UPS battery every six months.
Store at +30 to +45 °C (+86 to +113 °F), charge
the UPS battery every three months.
Orion Power Systems, Inc. Toll-Free: 877-385-1654
8640 Philips Hwy www.orionpowersystems.com
Jacksonville, FL 32256
FRONT PANEL EXPLANATIONS
1. Line LED ( ):
Green LED remains lit when incoming utility power is normal.
Green LED flashes every 2 seconds when the UPS is in battery charging mode.
Green LED remains lit and audible alarm beeps conti nu ou sly when the UPS is in overload condition.
2. Inverter LED ( )
Yellow LED flashes every 2 seconds and audible alarm beeps continuously during a power failure.
3. Overload LED ( )
Red LED remains lit and audible alarm beeps continuously when the UPS is in overload condition.
4. Check Battery LED ( )
Red LED flashes every 0.5 seconds and audible alarm beeps every 0.5 seconds when UPS is in battery low condition.
5. Main Switch:
a. To power on/off the UPS when incoming Utility power is normal.
b. To enable “DC-Start” Function when Utility fails. (To enable DC Start properly, you are recommended to connect <80%
output load with the UPS only). When using the “DC-Start”, ensure the equipment connected to the UPS is switched on.
It is not recommended to add other equipment after the DC-Start function is activated.
1
2 3 45
1. AC Inlet
REAR PANEL EXPLANATIONS
2. Backup Outlets: 6pcs NEMA5-15R
3. True RS232 interface port(Optional)
4. RJ11/RJ45 connector
5. Site Wiring Fault Indicator
6. USB Interface(Not supplied, if the RS232 interface is built)
7. Input fuse.
REPLACING THE BATTERY
Note: Once the battery is disconnected, the loads are not protected from power outages.
1. Use a phillips head screwdriver t o remove the two top cover screws and slide back the cover Please
refer to the figures STEP 1 through STEP 4.
2. Gently pull the batteries out of the UPS.
3. Loosen the black wire from the negative (-) terminal and red wire from the positive (+) terminal.
4. Connect the battery leads to the new batteries.
5. Note: Small sparks at the battery connectors are normal during connection.
6. Slide the batteries into the UPS.
7. Close the front panel and fasten two screws.
8. Dispose of the old batteries properly at an appropriate recycling facility.
Fuse:
1kVA: 12A/ 250V
1.5kVA: 15A/ 250V
-
3
5
4
2
7
1
6
If your UPS malfunctions during operation, please check the table below. Please consult Orion Power Systems Online Technical Support or call Orion Power
Systems for assistance with problems that cannot be resolved using the troubleshooting guide.
Situation Check Items Solution
Utility power is normal but the 'Line' LED is not on. 1. Is the power switch on? 2. Is the fuse
good? 3.Is the power cord loose?
'Inverter' LED flashes every 2 seconds but no output Battery voltage is too low Recharge the UPS for 24 hours.
Audible alarm beeps continuously when Util ity power
is normal.
Alarm buzzer beeps for 10 seconds followed by UPS
shutdown
No LEDs display on the front panel Contact Orion Power Systems Technical Support
UPS does not provide expected back up time. 1. The UPS battery is weak due to recent
The UPS operates normally, but the site wiring fault
indicator is lit.
UPS switch is on, but UPS does not operate Is the incoming Utility power normal?
Check for overload condition Reduce connected load by removing one or more devices.
Reduce connected load by removing one or more devices.
outage. 2.The UPS battery is near the end
of its service life.
Building wiring error such as missing ground
or hot to neutral wire reversal.
1. Press Power On button on front of unit. 2.Replace fuse
with same rating. 3.Re-connect the power cord properly.
1. Charge the battery. 2. If the battery is near the end of its
service life, replace the battery.
Have a qualified electrician correct the build in g w iring.
If Utility power is normal, connect ups to wall receptaclefirst
then switch on UPS.
TROUBLESHOOTING
Orion Power Systems, Inc. Toll-Free: 877-385-1654
8640 Philips Hwy www.orionpowersystems.com
Jacksonville, FL 32256
Loading...