Introduction
2
DIGITAL VIDEO
DVD VIDEO PLAYER & VIDEO
CASSETTE RECORDER
SD-V593SU
OWNER’S MANUAL
Connections
Basic setup
Playback
(VCR)
Recording
(VCR)
Other functions
(VCR)
Basic playback
(DVD)
Advanced
playback
(DVD)
16
25
32
37
42
45
48
©2005 Toshiba Corporation
This device does not tape-record copy protected DVD Video Discs.
Function setup
(DVD)
Others
58
65
2F90201A (E) COV 4/4/05, 9:01 PM1
Introduction
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: T O REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE
PARTSINSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle is intended to alert the user to the presence
of uninsulated dangerous voltage within the product's
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not expose this appliance to rain
or moisture.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN
BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
FCC NOTICE:This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Changes or modifications not expressly approved by the partly responsible for compliance with the
FCC Rules could void the user's authority to operate this equipment.
CAUTION: THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.
TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION.
USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE
ENCLOSURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS
OPENED. DO NOT STARE INTO BEAM.
Location of the required Marking
The rating sheet and the safety caution are on the rear of the unit.
CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE
STANDARDS, 21 CFR SUBCHAPTER J.
2
2F90201A (E)p02-15 4/4/05, 9:01 PM2
IMPORTANT SAFEGUARDS
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the unit is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the unit and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a soft dry cloth for cleaning the exterior cabinet only.
6. ATTACHMENTS
The manufacturer of this unit does not make any recommendations for attachments, as they may cause
hazards.
7. WATER AND MOISTURE
Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.
8. ACCESSORIES
Do not place this unit on an unstable cart, stand, tripod, bracket, or table.
The unit may fall, causing serious injury, and serious damage to the unit.
8A. An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.
9. VENTILATION
Slots and openings in the cabinet back or bottom are provided for ventilation,
to ensure reliable operation of the unit, and to protect it from overheating.
These openings must not be blocked or covered. The openings should never be blocked by placing the unit
on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat
source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided and/or the manufacturer’s instructions have been adhered to.
10. POWER SOURCE
This unit should be operated only from the type of power source indicated on the rating plate. If you are not
sure of the type of power supply to your home, consult your appliance dealer or local power company.
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
PORTABLE CART WARNING
(symbol provided by RETAC)
S3125A
Introduction
2F90201A (E)p02-15 4/4/05, 9:01 PM3
3
Introduction
IMPORTANT SAFEGUARDS
13. LIGHTNING
To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the
unit due to lightning and power line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from touching such power lines or circuits,
as contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is
grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the
National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for
the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
NATIONAL ELECTRICAL CODE
ANTENNA LEAD IN WIRE
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC SERVICE
EQUIPMENT
NEC-NATIONAL ELECTRICAL CODE
S2898A
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
18. SERVICING
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
For example:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d.
If the unit does not operate normally by following the operating instructions. Adjust only those controls that
are covered by the operating instructions, as an improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore the unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f . When the unit exhibits a distinct change in performance, this indicates a need for service.
4
2F90201A (E)p02-15 4/4/05, 9:01 PM4
IMPORTANT SAFEGUARDS / Power source
19. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
20. SAFETY CHECK
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.
21. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
22. DISC TRAY
Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.
23. CONNECTING
When you connect the product to other equipment, turn off the power and unplug all of the equipment from
the wall outlet. Failure to do so may cause a product damage. Read the owner's manual of the other
equipment carefully and follow the instructions when making any connections.
24. LASER BEAM
Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the
laser beam. It may cause sight damage.
25. DISC
Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious
personal injury and product malfunction.
26. NOTE TO CABLE TV SYSTEM INSTALLER
This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
Introduction
Power source
AC Outlet
Wider Hole
and Blade
Polarized AC Cord Plug
(One blade is wider than the other.)
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for operation on AC. Insert
the AC cord plug into a standard 120V 60Hz polarized AC outlet.
Notes:
Never connect the AC line cord plug to other than the specified
•
voltage (120V 60Hz). Use the attached power cord only.
If the polarized AC cord does not fit into a non-polarized AC
•
outlet, do not attempt to file or cut the blade. It is the user’s
responsibility to have an electrician replace the obsolete outlet.
If you cause a static discharge when touching the unit and the
•
unit fails to function, simply unplug the unit from the AC outlet
and plug it back in. The unit should return to normal operation.
2F90201A (E)p02-15 4/4/05, 9:01 PM5
5
Introduction
Precautions
Notes on handling
When shipping the DVD/VCR, the original shipping
carton and packing materials come in handy. For
maximum protection, repack the unit as it was
originally packed at the factory.
Do not use volatile liquids, such as insect spray, near
the DVD/VCR. Do not leave rubber or plastic
products to contact the DVD/VCR for a prolonged
period. They will leave marks on the finish.
The top and rear panels of the DVD/VCR may
become warm after a long period of use. This is not a
malfunction.
When the DVD/VCR is not in use, be sure to remove
the disc and the video cassette turn off the power.
If you do not use the DVD/VCR for a long period, the
unit may not function properly in the future. Turn on
and use the DVD/VCR occasionally.
Notes on locating
Place the DVD/VCR on a level surface. Do not use it
on a shaky or unstable surface such as a wobbling
table or inclined stand. The loaded disc or the video
tape may become disaligned and damage the DVD/
VCR.
When you place this DVD/VCR near a TV, radio or
VCR, the playback picture may become poor and the
sound may be distorted. In this case, place the DVD/
VCR away from the TV, radio or VCR.
Notes on moisture condensation
Moisture condensation damages the DVD/VCR.
Please read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the head drum or the optical
pick-up lens inside this unit, one of the most crucial
internal parts of the DVD/VCR.
f
o
m
e
o
l
p
i
s
m
a
x
E
n
o
c
Moisture condensation occurs during the
following cases.
When you bring the DVD/VCR directly from a cold
place to a warm place.
When you use the DVD/VCR in a room where you
just turned on the heater, or a place where the cold
wind from the air conditioner directly hits the unit.
In summer, when you use the DVD/VCR in a hot and
humid place just after you move the unit from an air
conditioned room.
When you use the DVD/VCR in a humid place.
t
u
r
e
s
n
a
e
t
i
d
o
n
!
It’s too
warm!
Tape
Head drum
Notes on cleaning
Use a soft, dry cloth for cleaning.
Use a dry cloth to wipe.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the
DVD/VCR.
If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.
6
Do not use the DVD/VCR when moisture
condensation may occur.
If you use the DVD/VCR in such a situation, it may
damage discs and internal parts. Remove the disc or
the video tape, connect the power cord of the DVD/
VCR to the wall outlet, turn on the DVD/VCR, and
leave it for two or three hours. After two or three
hours, the DVD/VCR will have warmed up and
evaporated any moisture. Keep the DVD/VCR
connected to the wall outlet and moisture
condensation will seldom occur.
Wait!
Wall outlet
2F90201A (E)p02-15 4/4/05, 9:01 PM6
Contents
Introduction
SAFETY PRECAUTIONS ................................ 2
IMPORTANT SAFEGUARDS .......................... 3
Power source ................................................... 5
Precautions ...................................................... 6
Contents. ..........................................................7
Notes and Information ...................................... 8
Identification of controls ................................. 12
Connections
Antenna connections...................................... 16
Cable TV connections ....................................18
Connecting to a TV ........................................ 20
Connecting to optional equipment.................. 23
Basic setup
Setting the video channel ............................... 25
Setting the language ...................................... 26
Clock setting................................................... 27
Tuner setting .................................................. 30
Playback (VCR)
Loading and unloading a cassette tape ......... 32
Cassette tape playback .................................. 33
Special playback ............................................ 34
Convenience function..................................... 35
Recording (VCR)
Recording a TV program ................................ 37
One-touch Timer Recording (OTR) ................ 39
Timer recording .............................................. 40
Basic playback (DVD)
Playing a disc ................................................. 45
Introduction
Advanced playback (DVD)
Zooming ......................................................... 48
Locating desired scene .................................. 48
Marking desired scenes ................................. 49
Repeat playback ............................................ 50
A-B Repeat playback ..................................... 50
Program playback .......................................... 51
Random playback .......................................... 51
Changing angles ............................................ 52
Title selection ................................................. 52
DVD menu...................................................... 52
Changing soundtrack language ..................... 53
Setting surround sound .................................. 53
Subtitles ......................................................... 54
To turn off the PBC (Video CD version 2.0) ... 54
MP3/WMA/JPEG operation............................ 55
Function setup (DVD)
Customizing the function settings .................. 58
Temporary disabling of rating level by
DVD disc ........................................................ 64
Others
Language code list ......................................... 65
Multi brand remote control ............................. 66
Troubleshooting .............................................. 68
Specifications ................................................. 69
Limited warranty ............................................. 70
Other functions (VCR)
Stereo recording and playback ...................... 42
Second Audio Program (SAP)........................ 42
Duplicating a video tape ................................. 43
Recording a DVD/CD disc.............................. 44
2F90201A (E)p02-15 4/4/05, 9:01 PM7
7
Introduction
Notes and Information
On handling discs
Do not touch the playback side of the disc.
Playback side
Do not attach paper or tape to discs.
On cleaning discs
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.
Structure of disc contents
Normally, DVD video discs are divided into titles, and
the titles are sub-divided into chapters. VIDEO CDs and
audio CDs are divided into tracks.
DVD video disc
DVD video disc
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3
Video CD/Audio CD
Video CD/Audio CD
Track 1 Track 2 Track 3 Track 4 Track 5
Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
There may be discs that do not have these numbers.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
8
2F90201A (E)p02-15 4/4/05, 9:01 PM8
About this owner’s manual
This owner’s manual explains the basic instructions of
this DVD/VCR. Some DVD video discs are produced in
a manner that allows specific or limited operation during
playback. As such, the DVD/VCR may not respond to all
operating commands. This is not a defect in the DVD/
VCR. Refer to instruction notes of discs.
” may appear on the TV screen during operation.
“
A “
” means that the operation is not permitted by the
DVD/VCR or the disc.
For example, sometimes it is unable to stop the
playback of copyright message of the disc when the
STOP ( ) button is pressed. Alternatively, the “ ” may
also indicate that the feature is not available for the disc.
Notes on region numbers
The region number of this DVD/VCR is 1. If region
numbers, which stand for their playable area, are printed
on your DVD video disc and you do not find
disc playback will not be allowed by the player. (In this
case, the DVD/VCR will display a message on-screen.)
ALL
1
or
,
On Video CDs
This DVD/VCR supports Video CDs equipped with the
PBC (Version 2.0) function. (PBC is the abbreviation of
Playback Control.) You can enjoy two playback
variations depending on types of discs.
• Video CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this DVD/VCR in
the same way as an audio CD.
• Video CD equipped with PBC function
(Version 2.0)
In addition to operation of a Video CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s
manual may not work with some discs.
Notes on copyright
The unauthorized recording, use, distribution, or revision
of television programs, videotapes, DVDs and other
materials, is prohibited under the Copyright Laws of the
United States and other countries, and may subject you
to civil and/or criminal liability.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be
authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Introduction
2F90201A (E)p02-15 4/4/05, 9:01 PM9
9
Introduction
Notes and Information (continued)
Playable discs
This DVD/VCR can play the following discs.
Disc
playback time
Size
12 cm
+
Approx. 80 minutes
8 cm
Approx. 160 minutes
(double sided disc)
Approx. 74 minutes
12 cm
+
8 cm
Approx. 20 minutes
Approx. 74 minutes
12 cm
8 cm
(CD
Approx. 20 minutes
single)
DVD
video
discs
Video
CDs
Audio
CDs
Disc Mark
DIGITAL VIDEO
Contents
Audio
Video
(moving
pictures)
Audio
Video
(moving
pictures)
Audio
Maximum
Approx. 4 hours
(single sided disc)
Approx. 8 hours
(double sided disc)
(single sided disc)
Because of problems and errors that can occur
during the creation of DVD and Video CD software
and/or the manufacture of DVD and Video CD discs,
Toshiba cannot guarantee that this DVD/VCR will
play every feature of every DVD bearing the DVD
logo and/or every Video CD bearing the CD logo.
As one of the creators of DVD technology, Toshiba
DVD players are manufactured using the highest
standards of quality, and as a result, such
incompatibilities are rare. If you happen to experience
any difficulty playing a DVD or a Video CD on a this
DVD/VCR, please feel free to call our Contact listed
in “How to Obtain Warranty Services” (page 71).
The following discs are also available.
DVD-R/RW discs of DVD video format
CD-R/CD-RW discs of CD-DA, Video CD, SVCD,
MP3, WMA or JPEG format
Kodak Picture CD and FUJICOLOR CD format
Some of these discs may be incompatible.
• You cannot play discs other than those listed above.
• You cannot play discs of DVD-RAM, DVD-ROM, Photo
CD, etc., or non standardized discs even if they may be
labeled as above.
• Some CD-R/RWs cannot be played back depending on
the recording conditions.
• This DVD/VCR uses the NTSC color system, and
cannot play DVD video discs recorded in any other
color system (PAL, SECAM, etc.).
10
2F90201A (E)p02-15 4/4/05, 9:01 PM10
Playable Media cards
This unit can play the following cards.
Playable
card
capacity
32 MB –
1 GB
8 MB –
1 GB
16 MB –
512 MB
16 MB –
128 MB
128 MB –
2 GB
8 MB –
4 GB
SD (Secure DigitalTM)
memory card
MMC
(MultiMediaCard
TM
Card Mark
)
Contents
MP3/
xD-Picture Card
WMA/
JPEG
Memory Stick
Memory StickTM (Pro)
CompactFlash
memory card (Type 1)
• Do not insert any cards other than those listed above as this
may cause a malfunction of the unit or cards.
• Some Media cards may not be played back due to its capac-
ity and/or manufacturer, etc.
• This unit cannot play the xD-Picture Card Type M.
TM
®
files
Notes on Media cards
• Ensure that you insert the Media card correctly into the media
card slot.
• Never remove the Media card or turn off the unit while using
the Media card. Doing so may result in loss of data or damage to the Media card or the unit. SUCH DAMAGE IS NOT
COVERED BY YOUR TOSHIBA WARRANTY.
• It is recommended that you back up your Media card data.
Toshiba is not liable for any damage caused by the use of
any Media card with this unit. Toshiba will not compensate
for any lost data or recording(s) caused by the use of such
cards.
• Media card is a precision electrical instrument. Do not bend,
drop or apply strong force to it.
• Do not use or store the Media card in an environment of
high static electricity or electrical interference.
• Avoid using or storing in areas of high temperature and hu-
midity.
• Prevent contact of the metallic area on the Media card with
dust, dirt, or other foreign particles. Do not touch the metallic area of the Media card with your hands or otherwise handle it with anything other than a soft, dry, lint-free, antistatic
cloth.
• Use index labels made exclusively for your specific brand of
Media card. Do not use commercially sold labels, which can
cause a malfunction when the card is inserted or ejected.
• When ejecting the Media card after extended use it may
feel warm to the touch. This is normal. The Media card is
not malfunctioning.
• For instructions on using your Media card, refer to the own-
er’s manual for your Media card.
Introduction
SD is a trademark of SD Card Association.
MMC and MultiMediaCard are trademarks of Infineon Technologies AG and licensed to MMCA (MultiMediaCard Association).
xD-Picture Card
Memory Stick is a trademark of Sony Corporation.
CompactFlash is a trademark of the Compact Flash Association.
Toshiba is an authorized licensee of the CompactFlash
2F90201A (E)p02-15 4/4/05, 9:45 PM11
TM
is a trademark of Fuji Photo Film Co., Ltd.
®
registered trademark.
11
Introduction
Identification of controls
See the page in for details.
Front panel
Cassette loading slot
ON/STANDBY button
REC button
EJECT
!
button
AUDIO (L/R)/VIDEO IN
(LINE IN 2) jacks
CHANNEL
"!
!%
#
/ buttons
!
Remote sensor
VCR indicator
!%
DVD indicator
#
#
Display window
"#
STOP button
Disc tray
VCR/DVD mode selector
PLAY button
button
#
Media card slot
!
[CompactFlash memory
card]
OPEN/CLOSE button
FF button
REV button
!!
!!
"#
Media card slot
SD memory card
MMC (MultiMediaCard)
#$
xD-Picture Card
Memory Stick (PRO)
"#
!!
!!
#$
Rear panel
AC power cord
12
DVD COAXIAL DIGITAL AUDIO OUT jack
DVD S-VIDEO OUT jack
HDMI OUT jack
5
DVD COMPONENT
OUT jacks
DVD OPTICAL DIGITAL
AUDIO OUT jacks
When connecting the optical digital cable, remove
the cap and fit the connector into the jack firmly.
When not using the jack, keep the cap inserted
!
to protect it from dust intrusion.
DVD/VCR common AUDIO
(L/R)/VIDEO OUT jacks
DVD AUDIO (L/R)
OUT jacks
AUDIO (L/R)/VIDEO
!
IN (LINE IN1) jacks
ANT IN jack
ANT OUT jack
"!
$
$
2F90201A (E)p02-15 4/4/05, 9:01 PM12
Display window
VCR indicator (VCR)
Play indicator
Still indicator
Introduction
Disc inserted indicator (DVD)
Recording
indicator (VCR)
Track indicator (CD)
Tape loaded indicator (VCR)
Progressive indicator
Timer Recording indicator (VCR)
VCR operation status
Press CALL to display VCR operation status on the screen.
To cancel the display, press CALL again.
While watching TV
DAY OF THE WEEK
CLOCK
STEREO AND
SECOND
AUDIO
PROGRAM
(SAP)
8 : 47
AM
MON
STEREO SAP
CH 125
00 : 00 : 00 SP
REAL TIME COUNTER
CHANNEL
TAPE SPEED
DVD/CD/VCD operation status
Multifunctional indicator
While operating a tape
HI-FI STEREO
8 : 30AM MON
HI-FI
STEREO
OUTPUT SELECTION
00 : 15 : 12 SP
OPERATING
MODE
AUTO REPEAT
TAPE IN
Disc inserted
indicator (CD)
AM/PM indicator
(AM is not displayed)
VCR Icons
Recording :
Rec/Pause
:
Play :
Stop :
Eject :
Each press of DISPLAY, the status display of the disc will appear on the screen and change as follows.
DVD
ELAPSED
TIME
CD/VCD
DISC
OPERATION
TRACK NO.
2F90201A (E)p02-15 4/4/05, 9:01 PM13
Track 11/99
00:34:56 01:12:33
34:56 71:33
TOTAL
TIME
TOTAL
TIME
ELAPSED TIME
DISC OPERATION
Title 1/99
1/8
Eng DolbyDigital
1/32
Eng
Chapter 1/999
00:34:56 01:12:33
1/9
TITLE NO.
ANGLE NO.
CHAPTER NO.
A KIND OF AUDIO
AUDIO LANGUAGE
SUBTITLE LANGUAGE
13
Introduction
Identification of controls (continued)
The instructions in this manual describe the functions on the remote control. See the page in for details.
Remote control
DVD/VCR button
* TV button
* CALL button
DISPLAY button
* CH / button
ZERO RETURN button
SEARCH button
CM SKIP button
ZOOM button
TOP MENU button
Direction buttons
PAUSE/STILL button
COUNTER RESET button
EJECT button (VCR)
OPEN/CLOSE (DVD)
()
SET+/– buttons
CH+/– buttons
CANCEL button
CLEAR button
PLAY button
REV button
SKIP button
VISS – button
VCR MENU button
SETUP button
MARKER button
ANGLE button
ATR button
SUBTITLE button
SP/SLP button
PLAYMODE button
DVD/CARD button
A-B RPT button
///
25
66
13
13
66
35
48
34
48
52
48
26
37
29
48
4533
4634
4733
47
36
26
58
49
35
52
34
54
37
50
56
50
32
45
MENU button
Use the MENU button to display the menu included on
many DVD video discs. To operate a menu, follow the
instructions in “DVD Menu.”
#
33
66
22
31
52
26 58
47
47
36
53
25
58
25
37
67
48
66
43
66
4533
4734
36
42
25
39
40
* POWER button
CABLE BOX button
Direct channel selection
buttons (0–9)
Number buttons (0–9)
* 100 button
* VOL +/– buttons
* INPUT SELECT button
PROGRAM button
MENU button
* ENTER button
RETURN button
STOP button
FF button
SKIP button
VISS + button
SLOW button
CLOCK/COUNTER button
HDMI button
AUDIO SELECT button
AUDIO button
DVD/VCR SELECT button
TV/VCR button
REC/OTR button
TIMER REC button
*TV control buttons
The various brands of TV listed on page 66 can be operated
with this remote control. There may be some TV models that
cannot be operated with this remote control. If this is the case,
use the original remote control supplied with the TV.
•CABLE BOX control buttons
The various brands of CABLE BOX listed on page 67 can
be operated with this remote control. There may be some
CABLE BOX models that cannot be operated with this
remote control. If this is the case, use the original remote
control supplied with the CABLE BOX.
14
2F90201A (E)p02-15 4/4/05, 9:01 PM14
Inserting batteries
Introduction
Open the battery compartment cover in the direction of
1
the arrow.
Caution:
Never throw batteries into a fire.
Notes:
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated disposal area.
•
Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with
applicable laws and regulations.
• If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with
new ones.
• When necessary to replace batteries in the remote control, always replace both batteries with new ones. Never mix
battery types or use new and used batteries in combination.
• Always remove batteries from remote control if they are dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid from leaking into the battery compartment.
Install two “AAA” batteries
(supplied),
23
polarity diagram in the battery
compartment.
paying attention to the
Replace the compartment
cover.
Remote control basics
• Press DVD/VCR to Operate the DVD/VCR.
• Press POWER to turn the DVD/VCR on or off.
• Select your desired operating mode (DVD or VCR) using DVD/VCR SELECT.
(DVD or VCR indicator on the front panel will show you which mode is selected.)
• Press CH + or CH – to move through the channels one channel at a time.
• The
• You can directly access specific channels using Direct channel selection buttons (0–9).
• Each press of DVD/VCR SELECT on the remote control, switches the screen between the VCR screen (VCR
Operation
• Aim the remote control at the remote sensor and press control buttons to
• Operate the remote control within 30° angle on either side of the remote
2F90201A (E)p02-15 4/4/05, 9:01 PM15
/ / / are also used to navigate on-screen menu system.
mode) and the DVD screen (DVD mode).
operate.
sensor, up to a distance of approx. 7 meters.
Approx. 7 meters
15
Connections
OUT
(TV)
IN
(ANT)
Antenna connections
If you are using an antenna system, follow these instructions. If you are a Cable TV subscriber, skip ahead to page 16 for
the proper connections.
Antenna to DVD/VCR connection
The DVD/VCR must be connected “between” the antenna and the TV. First, disconnect the antenna from the TV and connect
it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting an antenna system to
a DVD/VCR. Find the type of antenna system you are using and follow the connection diagram.
Combination VHF/UHF Antenna with 75 ohm Coaxial Cable
1
75 ohm Coaxial Cable
DVD/VCR
IN
(ANT)
OUT
(TV)
2
3
Note:
Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire
DVD/VCR
Matching Transformer 300 ohm Input 75
ohm output (not supplied)
300 ohm Twin Lead (Flat) Wire
Separate VHF and UHF Antennas
VHF
If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300 ohm inputs and
one 75 ohm output.
UHF
Combiner 75/300 ohm Inputs 75 ohm output
300 ohm Twin Lead (Flat) Wire
75 ohm Coaxial Cable
(not supplied)
(not supplied)
(not supplied)
IN
(ANT)
OUT
(TV)
DVD/VCR
Notes: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the antenna to
the DVD/VCR properly.
• For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an outdoor type
antenna is required.
• If you are not sure about the connection, please refer to qualified service personnel.
16
2F90201A (E)p16-28 4/4/05, 9:01 PM16
DVD/VCR to TV connection
After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow the
connection diagram.
This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna
inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.
Connections
75 ohm Coaxial Cable (supplied)
Splitter 75 ohm Input
75/300 ohm outputs
75 ohm Coaxial Cable
(supplied)
(not supplied)
TV
VHF/UHF IN
TV
UHF
VHF
Note: If a VHF or UHF antenna is used,
set the TV/CABLE menu option to
the “TV” mode.
TV with single 75 ohm VHF/UHF antenna
input
Note: If a VHF or UHF antenna is used,
set the TV/CABLE menu option
to the “TV” mode.
TV with 300 ohm UHF and 75 ohm VHF
antenna inputs
Splitter 75 ohm Input
300 ohm outputs
75 ohm Coaxial Cable
(supplied)
2F90201A (E)p16-28 4/4/05, 9:01 PM17
(not supplied)
TV
UHF
VHF
Note: If a VHF or UHF antenna is used,
set the TV/CABLE menu option to
the “TV” mode.
TV with 300 ohm UHF and 300 ohm VHF
antenna inputs
17
Connections
Cable TV connections
Many cable companies offer services permitting reception of extra channels including pay or subscription channels. This
DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable company
supplied converter box, except for those premium channels which are intentionally scrambled. If you subscribe to a
premium channel which is scrambled, you must have a descrambler box for proper reception.
1
DVD/VCR
IN
Incoming Cable
Allows:*Recording of nonscrambled channels.
Use of the programmable timer.
*
Recording of one channel while watching another.
*
DVD/VCR
2
Incoming
Allows:*Recording of channels through the converter box
Prevents:*Recording one channel while watching another.
Converter/
Descrambler
Cable
(scrambled and unscrambled).
Using the programmable timer to record only the
*
channel selected at the converter box.
Using the DVD/VCR tuner to select channels.
*
(ANT)
OUT
(TV)
IN
(ANT)
OUT
(TV)
TV
VHF/UHF
IN (ANT)
TV
VHF/UHF
IN (ANT)
Note:
To record from converter/descrambler, DVD/
VCR tuner must be tuned to the converter
output channel, usually channel 3 or 4.
DVD/VCR
3
IN
Incoming Cable
Allows:*Recording of nonscrambled channels.
Use of the programmable timer.
*
Recording an unscrambled channel while watching
*
any channel selected at the converter box.
Prevents: Recording scrambled channels.
Note: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to the output of
the Converter/Descrambler box, usually channel 3 or 4.
(ANT)
OUT
(TV)
Converter/Descrambler
Note:
If you are playing a tape or using the tuner
built into the DVD/VCR, the converter must
be set to the video channel output of the DVD/
VCR (either 3 or 4).
18
2F90201A (E)p16-28 4/4/05, 9:01 PM18
VHF/UHF
IN (ANT)
TV
IMPORTANT: Make sure the TV/CABLE menu option is set to the “CABLE” mode.
This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambled programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult your local cable company for more information concerning connection to their descrambler equipment. There are
many ways to connect your DVD/VCR to a cable system. Below are six common methods of connection.
DVD/VCR
4
Incoming Cable
Splitter
Converter/Descrambler
IN
(ANT)
OUT
(TV)
A/B Switch
A
B
TV
VHF/UHF
IN (ANT)
Allows:*Recording of one channel while watching another.
Using the programmable timer to record only the channel selected at the converter box.
*
Recording of all channels through the converter box.
*
Prevents:*Watching scrambled channels while recording another channel.
Using the DVD/VCR tuner to select channels.
*
DVD/VCR
5
Splitter
Incoming Cable
Converter/Descrambler
IN
(ANT)
OUT
(TV)
A/B Switch
A
B
TV
VHF/UHF
IN (ANT)
Connections
Allows:*Recording of nonscrambled channels.
Recording of one channel while watching another.
*
Watching premium channels through the converter while recording nonscrambled channels.
*
Using the programmable timer.
*
Prevents: Recording scrambled channels.
DVD/VCR
6
Splitter
Incoming Cable
Converter/Descrambler
Converter/Descrambler
IN
(ANT)
OUT
(TV)
Allows:*Recording of all channels through the converter box.
Recording a scrambled or unscrambled channel while watching another (scrambled or
*
unscrambled) channel.
Using the programmable timer to record only the channel selected at the converter box.
*
Prevents: Using the DVD/VCR tuner to select channels.
A/B Switch
A
B
TV
VHF/UHF
IN (ANT)
19
2F90201A (E)p16-28 4/4/05, 9:01 PM19
Connections
Connecting to a TV
Connect the DVD/VCR to your TV.
Note: This method transports VHS and DVD-video signals. For enhanced DVD-video performance, we recommend you
also connect the S-video, ColorStream
Connecting to a TV
Signal flow
®
component video or HDMI outputs to your TV/monitor.
(red) (white)
(yellow)
To wall outlet
To VIDEO
OUT
To video input
(yellow)
• Make sure following setting.
On-screen display
“Digital Out”
Notes:
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD/VCR to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.
• If your television set has one audio input, connect the left and right audio outputs of the DVD/VCR to a Y cable adapter (not
supplied) and then connect to your TV.
• Connect the DVD/VCR directly to your TV. If you connect the DVD/VCR to a VCR, TV/VCR combination or video selector,
the playback picture may be distorted as DVD video discs are copy protected.
Select:
“PCM” or “Raw”
Page
$
To ANALOG AUDIO OUT
Audio/video cable (supplied)
To audio inputs
(white)
(red)
TV or monitor with
audio/video inputs
20
2F90201A (E)p16-28 4/4/05, 9:01 PM20
S-video output
An S-Video connection is superior to Video (Yellow) output. Use this method for DVD playback when the connected television has SVideo input, and does not have component video inputs.
Component video outputs
PROGRESSIVE outputs
Some TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively scanned video
signal. Connecting to these inputs allows you to view the highest quality pictures with less flicker.
INTERLACED outputs
Some TVs or monitors are equipped with component video inputs. Connecting to these inputs allows you to enjoy the highest quality
DVD picture playback.
Notes:
• Actual labels for component video inputs may vary depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)
• In some TVs or monitors, the color levels of the playback picture may be reduced slightly or the tint may change. In such a
case, adjust the TV or monitor for optimum performance.
Connections
Connecting to an audio system and TV equipped with S-video input/component video inputs
The S-video output and component video output transports the DVD-video signal exclusively and will deliver enhanced DVD
video picture performance.
Signal flow
To ANALOG
AUDIO OUT
(white)
(red)
To wall outlet
To switch the scan
mode between the
interlace and
progressive modes,
see page 63.
To SVIDEO
OUT
To PR/C
VIDEO
OUT
R
To PB/C
VIDEO
OUT
B
To Y
VIDEO
OUT
Component
video cable
(not supplied)
If you connect the DVD/VCR to
your TV with the DVD OUT jacks,
select the corresponding video
input on your television to watch
DVD video discs.
Audio cable (not supplied)
To audio inputs of
the amplifier
To
To
PR/CR
To Y video input
PB/CB
video input
video input
(red)
(white)
To S-video input
• Make sure following setting.
S-video cable (not supplied)
TV or monitor with
ColorStream
®
Audio system
component video inputs
On-screen display
“Digital Out”
Select:
“PCM” or “Raw”
Page
$
Notes:
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
• If you place the DVD/VCR near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD/
VCR away from the tuner and radio.
• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, the
speakers may be damaged.
• When connecting to a TV using the Video or S-video jack, make sure that the Progressive indicator “
” on the
display window is not lit. If it is lit, the Video and S-video outputs do not feed the correct signals and you cannot see
any picture. To turn off the Progressive indicator, select PROGRESSIVE scan Off
$!
.
21
2F90201A (E)p16-28 4/4/05, 9:02 PM21
Connections
Connecting to a TV (continued)
About HDMI
HDMI (High Definition Multimedia Interface) supports both video
and audio on a single digital connection for use with DVD players,
DTV, set-top boxes, and other AV devices. HDMI was developed
to provide the technologies of High Bandwidth Digital Content
Protection (HDCP) as well as Digital Visual Interface (DVI) in one
specification. HDCP is used to protect digital content transmitted
and received by DVI-compliant or HDMI-compliant displays.
HDMI has the capability to support standard, enhanced, or highdefinition video plus standard to multi-channel surround-sound
audio. HDMI features include uncompressed digital video, a
bandwidth of up to 2.2 gigabytes per second (with HDTV signals),
one connector (instead of several cables and connectors), and
communication between the AV source and AV devices such as
DTVs.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI licensing LLC.
Connecting to a display (Using the HDMI cable)
Signal flow
To wall outlet
To HDMI OUT
HDMI Cable (supplied)
Switching the video quality (HDMI mode) using HDMI
button on the remote control
Press HDMI on the remote control to receive suitable video
quality. The video quality is required to match your TV having
HDMI feature and suitable quality, please check your TV
owner's manual.
Pressing HDMI changes the video quality as follows:
To HDMI input
HDMI-compatible display
• Make sure following setting.
On-screen display
“Digital Out”
Select:
“PCM”
Page
$
480p 720p 1080i
Notes:
• Refer to the Owner's manual of the connected TV as Well.
• When you connect the DVD/VCR to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.
• If you have a HDMI (with HDCP) equipped monitor or display, you can connect it to the DVD/VCR using the supplied HDMI
cable.
• The HDMI connector outputs uncompressed digital video, as well as almost every kind of digital audio that the DVD/VCR is
compatible with, including DVD-Video, Video CD, CD and MP3.
• No sound will be output from the HDMI cable if the Digital Out is not set to PCM
$
.
22
2F90201A (E)p16-28 4/4/05, 9:02 PM22
Connecting to optional equipment
You can enjoy high quality dynamic sounds of DVD video discs or
audio CDs by connecting the DVD/VCR to optional audio
equipment.
For connection to your TV, see “Connecting to a TV”
.
• This selection uses the following reference mark.
: Front speaker
: Rear speaker
: Center speaker
: Signal flow
: Sub woofer
Connecting to an amplifier equipped with a Dolby Digital decoder
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is
now available to reproduce this realistic effect in the home. You can enjoy motion picture and live
concert DVD video discs encoded via the Dolby Digital recording system with this dynamic realistic
sound by connecting the DVD/VCR to a 6 channel amplifier equipped with a Dolby Digital decoder
or Dolby Digital processor. If you have a Dolby Pro Logic Surround decoder, you will obtain the full
benefit of Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital soundtracks,
as well as from titles with the Dolby Surround mark.
Amplifier equipped with a
Dolby Digital decoder
To COAXIAL
type digital
audio input
To OPTICAL
type digital
audio input
Optical cable (not supplied)
75 1 coaxial cable (not supplied)
Manufactured under license from
Dolby Laboratories. “Dolby” “Pro
Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
• Use DVD video discs
encoded via the Dolby Digital
recording system.
• Make sure following setting.
On-screen display
“Digital Out”
Connect either
“PCM” or “Raw”
Select:
Connecting to an amplifier equipped with Dolby Surround Pro Logic
Dolby Surround Pro Logic
You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right and left
front speakers, a center speaker, and one or two rear speakers).
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an amplifier
equipped with a Dolby Digital decoder.” Refer to that amplifier’s owner’s manual and set
the amplifier so you can enjoy Dolby Surround Pro Logic sound.
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
• This connection is only suitable for Video CDs and
Audio CDs.
*
Amplifier equipped with
Dolby Surround Pro Logic
To audio input
Audio cable (not supplied)
• Make sure following setting.
On-screen display
“Digital Out”
Connect one or two rear speakers.
*
The output sound from the rear
speakers will be monaural even if you
connect two rear speakers.
To ANALOG
AUDIO OUT
Select:
“PCM” or “Raw”
Connections
Page
$
Page
$
Connecting to an amplifier equipped with a DTS decoder
Digital Theater Systems (DTS)
DTS is a high quality surround technology used in theaters and now available for home use,
on DVD video discs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full
benefit of 5.1 channel DTS encoded sound tracks on DVD
video discs or audio CDs.
Amplifier equipped with a
DTS decoder
To COAXIAL
type digital
audio input
To OPTICAL
type digital
audio input
Optical cable (not supplied)
75 1 coaxial cable (not supplied)
“DTS” and “DTS Digital Out” are
trademarks of Digital Theater Systems,
Inc.
• Use DVD video discs or audio
CDs encoded via the DTS
recording system.
• Make sure following setting.
On-screen display
“Digital Out”
Connect either
Select:
“Raw”
Page
$
23
2F90201A (E)p16-28 4/4/05, 9:47 PM23
Connections
Connecting to optional equipment (continued)
Warning
When playing DTS-encoded discs (audio CDs), excessive noise may be output from the analog stereo jacks. To avoid
possible damage to the audio system, you should take proper precautions when the ANALOG AUDIO OUT (L/R) jacks of the
DVD/VCR are connected to an amplification system. (Do not leave the ANALOG AUDIO OUT (L/R) wires dangling.) To enjoy
DTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must be connected to the
COAXIAL DIGITAL AUDIO OUT jack of the DVD/VCR.
Connecting to an amplifier equipped with an MPEG2 audio decoder
MPEG2 sound
You can enjoy motion picture and live concert DVD video discs encoded via the MPEG2 recording system with dynamic realistic sound
by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2 audio processor.
• Use DVD video discs
encoded via the MPEG2
Amplifier equipped with an
MPEG2 audio decoder
To COAXIAL
type digital
audio input
To OPTICAL
type digital
audio input
Optical cable (not supplied)
Connect either
75 1 coaxial cable (not supplied)
recording system.
• Make sure following setting.
On-screen display
“Digital Out”
Select:
“PCM” or “Raw”
Page
$
Connecting to an amplifier equipped with a digital audio input
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input and speaker
system (right and left front speakers).
Amplifier equipped with a
digital audio input
To COAXIAL
type digital
audio input
Notes:
• DO NOT connect the OPTICAL or COAXIAL DIGITAL AUDIO OUT jack of the DVD/VCR to the AC-3 RF input of a Dolby
Digital Receiver. This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the OPTICAL or
COAXIAL DIGITAL AUDIO OUT jack of the DVD/VCR.
• Connect the OPTICAL DIGITAL AUDIO OUT jack of the DVD/VCR to the “OPTICAL” input of a Receiver or Processor.
• Connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD/VCR to the “COAXIAL” input of a Receiver or Processor.
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers and your hearing may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, the
speakers may be damaged.
To OPTICAL
type digital
audio input
Optical cable (not supplied)
75 1 coaxial cable (not supplied)
• Make sure following setting.
On-screen display
“Digital Out”
Connect either
“PCM” or “Raw”
Select:
Page
$
24
2F90201A (E)p16-28 4/4/05, 9:02 PM24
Basic setup
Setting the video channel
When a TV is connected with the 75 ohm coaxial cable only.
To view playback of a recorded tape or DVD disc, or to watch a
program selected by the VCR's channel selector, the TV must be set to
channel 3 or 4 (video channel).
Setting the video channel
POWER
DVD/VCR
3
4
TV/VCR
DVD/VCR SELECT
Press DVD/VCR to operate the DVD/VCR.
1
Press and hold 3 or 4 on the remote for 3
seconds in standby mode.
2
The video channel will
OR
Press POWER to turn on the DVD/VCR.
start to flash for 3
seconds in the display
window.
3
Press DVD/VCR SELECT selector to select the
VCR mode.
4
The VCR indicator on the
front panel will light.
For a push-button TV tuner
If CH 3 or 4 corresponding to the video channel cannot
be tuned on your TV, proceed as follows: set the VCR
3/4 channel selector and the TV to CH 3 or 4, play
back a prerecorded tape and tune the TV to receive a
sharp color picture from the video cassette recorder.
Refer to your TV owner's manual for details.
Note:
If the unit does not operate properly, or No key operation
(by the unit and/or the remote control): Static electricity, etc.,
may affect the player's operation. Disconnect the AC power cord
once, then connect it again.
Basic setup
Turn ON the TV and set to CH 3 or 4 to correspond with the channel selected in step 2.
5
Press TV/VCR to select the VCR position.
6
Select any channel to receive a TV station in your area.
The channel number will appear on the screen for
7
about 4 seconds.
2F90201A (E)p16-28 4/4/05, 9:02 PM25
The VCR indicator will
appear in the display
window.
25
Basic setup
Setting the language
You can choose from three different languages (English,
French and Spanish) for the on-screen displays.
Setting the language
DVD/VCR
ENTER
SET +/–
VCR MENU
DVD/VCR SELECT
Preparation:
• Turn ON the TV and select to the corresponding
video input.
• Press DVD/VCR to operate the DVD/VCR.
• Press DVD/VCR SELECT to select the VCR mode.
(The VCR indicator will light.)
Press VCR MENU.
1
Press SET + or – to select “LANGUAGE”, then
press ENTER.
2
The VCR menu screen will appear.
Press SET + or – to select “SYSTEM
SETUP”, then press ENTER.
If you use the unit for the first time and
press VCR MENU, instead of the
main menu screen the “SYSTEM
SETUP” menu screen in step 2 may
appear.
MENU
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
〈+/-
/ENTER/MENU
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
DAYLIGHT SAVING TIME
-
/ENTER/MENU
〈
+/
ON OFF
ON OFF
〉
ON OFF
ON OFF
〉
Press VCR MENU until the MENU screen is
cleared.
4
Notes:
• Both the VCR and the DVD have their own player menus
• If no buttons are pressed for more than 60 seconds, the VCR
MENU screen will return to normal TV-operation automatically.
#
&
.
Press SET + or – to select the desired language:
English (ENGLISH), Spanish (ESPAÑOL) or
3
French (FRANCAIS), then press ENTER.
26
2F90201A (E)p16-28 4/4/05, 9:02 PM26
LANGUAGE/IDIOMA/LANGUE
ENGLISH
ESPAOL
FRANCAIS
〈+/-
/ENTER/MENU
〉
Clock setting
The AUTO CLOCK function will automatically set the built-in clock
(Month, Day, Year and Time) when the DVD/VCR is connected to an
Antenna or Cable system and it is turned off. The DVD/VCR searches
for a station in your area containing the necessary AUTO CLOCK setting
signals. Once received, it will take approximately 4 minutes for the clock
to set itself automatically.
POWER
DVD/VCR
CALL
ENTER
SET +/–
VCR MENU
DVD/VCR SELECT
AUTO CLOCK setting
Preparation:
• Turn ON the TV and select the corresponding video input.
• Press DVD/VCR to operate the DVD/VCR.
• Press DVD/VCR SELECT to select the VCR mode.
(The VCR indicator will light.)
Connect the Antenna or Cable system.
1
Plug the AC power cord to the AC outlet.
• If you use a cable box, turn it on.
2
Make sure the DVD/VCR is turned off.
3
Wait at least three minutes and press POWER.
• Depending on the reception
condition it may take approx. thirty
minutes.
• If you press POWER, the Auto
Clock set is not programmed.
4
Press CALL to check the clock setting on
the on screen display.
5
8 : 47
AM MON
STEREO SAP
CH 125
To set AUTO CLOCK to off
When shipped from factory the AUTO CLOCK is set to “ON”.
But if you do not want AUTO CLOCK setting:
Press VCR MENU.
1
Press SET + or – to select “SYSTEM SETUP”,
then press ENTER.
2
Press SET + or – to select “AUTO CLOCK”.
MENU
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
+/Ð/ENTER/MENU
MENU
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
+/Ð/ENTER/MENU
ONONOFF
OFF
ONONOFF
OFF
3
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
DAYLIGHT SAVING TIME
+/Ð/ENTER/MENU
ONONOFF
OFF
Basic setup
If the clock is not set, check the antenna
condition. The AUTO CLOCK may not
6
function properly if the reception condition
is not good.
AUTO CLOCK adjustment
The auto clock adjustment will be updated at 6:00
AM, 12:00 PM and 6:00 PM everyday when the DVD/
VCR turned off.
• If you use a cable box and you want AUTO CLOCK
adjustment to be performed, the cable box must be
left on.
• The AUTO CLOCK adjustment is not effective when
there is a difference of more than 5 minutes exists
between the built-in clock time and the actual time.
2F90201A (E)p16-28 4/4/05, 9:02 PM27
00 : 00 : 00 SP
Press ENTER to select “OFF”.
4
Press VCR MENU repeatedly to return to the
normal screen.
5
• When the AUTO CLOCK is set to
“OFF”, the AUTO CLOCK adjustment does not function.
• Set the clock manually
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
DAYLIGHT SAVING TIME
+/Ð/ENTER/MENU
ONONOFF
'
OFF
.
27
Basic setup
Clock setting (continued)
To set STANDARD TIME
In the rare event that you live within broadcast range of two
stations in two different time zones, the DVD/VCR may recognize
the wrong station for the AUTO CLOCK setting.
To correct the situation:
Press VCR MENU.
1
Press SET + or – to select “SYSTEM SETUP”,
then press ENTER.
2
Press
SET + or –
then press ENTER.
3
Press SET + or – to select your time zone,
then press ENTER.
4
Press VCR MENU until the MENU screen is
cleared.
5
to select “STANDARD TIME”
ATLANTIC : GMT–4hours
EASTERN : GMT–5hours
CENTRAL : GMT–6hours
MOUNTAIN : GMT–7hours
PACIFIC : GMT–8hours
ALASKA : GMT–9hours
HAWAII : GMT–10hours
AUTO : AUTO SET
(GMT: Greenwich Mean Time)
MENU
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
+/Ð/ENTER/MENU
MENU
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
+/Ð/ENTER/MENU
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
DAYLIGHT SAVING TIME
-
/ENTER/MENU
〈
+/
ONONOFF
ONONOFF
ON OFF
ON OFF
〉
OFF
OFF
,
To set DAYLIGHT SAVING TIME
You can set the DAYLIGHT SAVING TIME automatically or
manually.
Press VCR MENU.
Press SET + or – to select “SYSTEM SETUP”,
1
then press ENTER.
MENU
Press SET + or – to select “DAYLIGHT
SAVING TIME”, then press ENTER.
2
Press SET + or – to select one of the
options, then press ENTER. Press VCR
3
MENU until the MENU screen is cleared.
ON:
OFF:
AUTO:
When you want to set the
SAVING TIME
Sunday in April you set to “ON”, and
on the last Sunday in October you set
to “OFF”.
for manual setting
(forward one hour)
for manual setting
(back one hour)
for automatic setting
(read XDS in the signal)
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
+/Ð/ENTER/MENU
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
DAYLIGHT SAVING TIME
+/Ð/ENTER/MENU
manually, on the first
DAYLIGHT SAVING TIME
〈
+/
-
/ENTER/MENU
ON
OFF
AUTO
ONONOFF
OFF
ONONOFF
OFF
DAYLIGHT
〉
Notes:
• To be able to select the standard time, the clock must first be
set by AUTO CLOCK once.
• If you live in Newfoundland and the AUTO CLOCK does not
function properly, set the AUTO CLOCK menu option to “OFF”
and set the clock manually.
28
2F90201A (E)p16-28 4/4/05, 9:02 PM28
Notes:
• When shipped from factory, the DAYLIGHT SAVING TIME is
set to “AUTO” position.
• When the clock is not set, DAYLIGHT SAVING TIME setting
is not available.
• When there is no DAYLIGHT SAVING TIME in your area, always select “OFF” position in step 3.
If the AUTO CLOCK process did not set the date and time correctly, you
must set them manually for timer recording and DAYLIGHT SAVING TIME.
Manual clock setting
SET +/–
ENTER
CANCEL
VCR MENU
EXAMPLE: Setting the clock to “8:30 AM” March, 26
(SAT), 2005.
Press VCR MENU.
1
Press SET + or – to select “SYSTEM SETUP”,
then press ENTER.
2
MENU
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
+/Ð/ENTER/MENU
Press SET + or – to select “CLOCK SET”,
then press ENTER.
3
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
DAYLIGHT SAVING TIME
〈+/-
/ENTER/MENU
ONONOFF
ON OFF
ON OFF
〉
OFF
After setting the clock, date and time starts
functioning automatically.
6
8 : 30AMSAT
To make corrections any time during the process
Press CANCEL repeatedly until the item you want to
change blinks, then press SET + or –.
Note:
After a power failure or disconnection of the power, the timer
settings will be lost. In this case, reset the present time.
Basic setup
Press SET + or – to set the month, then press
ENTER.
4
Set the day, year and time as in step 4.
5
2F90201A (E)p29-34 4/4/05, 9:02 PM29
MONTH
3
DAY
1 (TUE)
YEAR
2005
TIME
〈+/Ð
〈+/Ð
12 : 00
/ENTER/CANCEL/MENU
MONTH
3
DAY
26 (SAT)
YEAR
2005
TIME
8:30
/ENTER/CANCEL/MENU
AM
〉
AM
〉
29
Basic setup
Tuner setting
DVD/VCR
This DVD/VCR is equipped with a channel memory feature which allows
channels to skip up or down to the next channel set into memory,
skipping over unwanted channels. Before selecting channels, they must
be programmed into the DVD/VCR’s memory. In addition to normal
VHF and UHF channels, this DVD/VCR can receive up to 113 Cable
TV channels. To use this DVD/VCR with an antenna, set the TV/CABLE
menu option to the TV mode. When shipped from the factory, this menu
option is in the CABLE mode.
TV/CABLE selection Setting channels automatically
Preparation:
• Turn ON the TV and select to the corresponding
video input.
• Press DVD/VCR to operate the DVD/VCR.
• Press DVD/VCR SELECT to select the VCR mode.
(The VCR indicator will light.)
Press VCR MENU. Press
“CH SETUP”, then press ENTER.
1
SET + or –
MENU
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
to select
ONONOFF
OFF
Repeat left step 1 and press SET + or – to
select “AUTO CH MEMORY”.
1
Press ENTER.
2
Auto tuning will begin. The channel display will count up and when finished,
the screen returns to normal.
ENTER
SET +/–
VCR MENU
DVD/VCR SELECT
CH SETUP
TV CABLE
AUTO CH MEMORY
ADD/DELETE
〈+/-
/ENTER/MENU
〉
+/Ð/ENTER/MENU
Press SET + or – to select “TV/CABLE”.
2
Press ENTER to select the TV or CABLE
mode.
3
The arrow indicates the selected mode.
TV - VHF/UHF channels
CABLE - Cable TV channels
Press VCR MENU until the menu screen is
cleared.
4
CH SETUP
AUTO CH MEMORY
ADD/DELETE
+/Ð/ENTER/MENU
CH SETUP
AUTO CH MEMORY
ADD/DELETE
+/Ð/ENTER/MENU
+0
TV
CABLE
TV
CABLE
Note:
You can’t select “CH SETUP” if you set the channel to “L1” or
“L2”.
30
2F90201A (E)p29-34 4/4/05, 9:48 PM30
Loading...