ORION ELECTRIC M2C5B User Manual

Introduction

2

DIGITAL VIDEO

DVD VIDEO PLAYER & VIDEO
CASSETTE RECORDER

SD-V391

OWNER’S MANUAL

Connections

Basic setup

Playback

(VCR)

Recording (VCR)

Other functions

(VCR)

Basic playback

(DVD)

Advanced

playback

(DVD)

14

22

29

34

39

42

45

©2003 T oshiba Corporation
This device does not tape-recorded copy protected DVD Video Discs.

DVD VIDEO PLAYER / VIDEO CASSETTE RECORDER SD-V391

Function setup

(DVD)

Others

55

68

2C51701A (E)COV 19/05/2003, 10:341

Introduction

IMPORTANT SAFEGUARDS

The lightning flash with arrowhead symbol, within an

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE
P ARTS INSIDE. REFER SERVICING T O
QUALIFIED SER VICE PERSONNEL.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not expose this appliance to rain

or moisture.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN

EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN
BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications .
However, there is no guarantee that interference will not occur in a par ticular installation. If this
equipment does cause harmful interference to radio or television reception, which can be deter­mined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:

equilateral triangle is intended to alert the user to the presence
of uninsulated dangerous voltage within the product's
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Changes or modifications not expressly approved by the partly responsible for compliance with the
FCC Rules could void the user's authority to operate this equipment.

CAUTION: THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.

TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CARE­FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTE­NANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE.

USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLO­SURE. VISIBLE LASER RADIATION MA Y BE PRESENT WHEN THE ENCLOSURE IS OPENED .
DO NOT STARE INTO BEAM.

Location of the required Marking

The rating sheet and the safety caution are on the rear of the unit.

CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE
STANDARDS, 21 CFR SUBCHAPTER J.

2

2C51701A (E)p02-13 19/05/2003, 10:342

IMPORTANT SAFEGUARDS

1. READ INSTRUCTIONS

All the safety and operating instructions should be read before the unit is operated.

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

3. HEED WARNINGS

All warnings on the unit and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

5. CLEANING

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning the exterior cabinet only.

6. ATTACHMENTS

The manufacturer of this unit does not make any recommendations for attachments, as they may cause
hazards.

7. WATER AND MOISTURE

Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundr y tub, in a wet
basement, or near a swimming pool.

8. ACCESSORIES

Do not place this unit on an unstable cart, stand, tripod, bracket, or table.
The unit may fall, causing serious injury, and serious damage to the unit.

8A. An appliance and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.

9. VENTILATION

Slots and openings in the cabinet back or bottom are provided for ventilation,
to ensure reliable operation of the unit, and to protect it from overheating.
These openings must not be blocked or covered. The openings should never be blocked by placing the unit
on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat
source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided and/or the manufacturer’s instructions have been adhered to.

10. POWER SOURCE

This unit should be operated only from the type of power source indicated on the rating plate. If you are not
sure of the type of power supply to your home, consult your appliance dealer or local power company. For
units intended to operate from battery power, or other sources, refer to the operating instructions.

11. GROUNDING OR POLARIZATION

This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug, if your
unit is equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only
fit into a grounding-type power outlet. This too, is a safety feature. If you are unable to insert the plug into
the outlet, contact your electrician to replace your obsolete outlet.Do not defeat the safety purpose of the
grounding-type plug.

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.

PORTABLE CART WARNING

(symbol provided by RETAC)

S3125A

Introduction

2C51701A (E)p02-13 19/05/2003, 10:343

3

Introduction

IMPORTANT SAFEGUARDS

13. LIGHTNING

To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the
unit due to lightning and power line surges.

14. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits, as
contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is
grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the
National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for
the grounding electrode.

18. SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.

19. DAMAGE REQUIRING SERVICE

Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following
conditions:

a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instructions. Adjust only those

controls that are covered by the operating instructions, as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the

unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f . When the unit exhibits a distinct change in performance, this indicates a need for service.

20. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.

21. SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.

22. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.

23. DISC TRAY

Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.

24. CONNECTING

When you connect the product to other equipment, turn off the power and unplug all of the equipment from
the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's
manual of the other equipment carefully and follow the instructions when making any connections.

4

2C51701A (E)p02-13 19/05/2003, 10:344

IMPORTANT SAFEGUARDS / Power source

25. LASER BEAM

Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the
laser beam. It may cause sight damage.

26. DISC

Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious
personal injury and product malfunction.

27. NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con­nected to the grounding system of the building, as close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

Introduction

GROUND CLAMP

ELECTRIC SERVICE

EQUIPMENT

NEC-NATIONAL ELECTRICAL CODE
S2898A

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)

GROUNDING CONDUCTORS
(NEC SECTION 810-21)

GROUND CLAMPS
POWER SERVICE GROUNDING

ELECTRODE SYSTEM
(NEC ART 250, PART H)

CONDENSATION

Moisture will form in the operating section of the DVD/VCR if the player is brought from cool surroundings into a
warm room or if the temperature of the room rises suddenly. When this happens, the DVD/VCR's performance
will be impaired.
To prevent this, let the DVD/VCR stand in its new surroundings for about an hour before switching it on, or make
sure that the room temperature rises gradually.
Condensation may also form during the summer if the DVD/VCR is exposed to the breeze from an air
conditioner. In such cases, change the location of the DVD/VCR.

Power source

AC Outlet

Wider Hole
and Blade

Polarized AC Cord Plug
(One blade is wider than the other.)

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for operation on AC. Insert
the AC cord plug into a standard 120V 60Hz polarized AC outlet.

Notes:

Never connect the AC line cord plug to other than the specified

•
voltage (120V 60Hz). Use the attached power cord only.
If the polarized AC cord does not fit into a non-polarized AC

•
outlet, do not attempt to file or cut the blade. It is the user’s
responsibility to have an electrician replace the obsolete outlet.
If you cause a static discharge when touching the unit and the

•
unit fails to function, simply unplug the unit from the AC outlet
and plug it back in. The unit should return to normal operation.

2C51701A (E)p02-13 19/05/2003, 10:345

5

Introduction

Precautions

Notes on handling

When shipping the DVD/VCR, the original shipping
carton and packing materials come in handy. For
maximum protection, repack the unit as it was
originally packed at the factory.
Do not use volatile liquids, such as insect spray, near
the DVD/VCR. Do not leave rubber or plastic
products to contact the DVD/VCR for a prolonged
period. They will leave marks on the finish.
The top and rear panels of the DVD/VCR may
become warm after a long period of use. This is not a
malfunction.
When the DVD/VCR is not in use, be sure to remove
the disc and the video cassette turn off the power.
If you do not use the DVD/VCR for a long period, the
unit may not function properly in the future. Turn on
and use the DVD/VCR occasionally.

Notes on locating

Place the DVD/VCR on a level surface. Do not use it
on a shaky or unstable surface such as a wobbling
table or inclined stand. The loaded disc or the video
tape may become dis-aligned and damage the DVD/
VCR.
When you place this DVD/VCR near a TV, radio, or
VCR, the playback picture may become poor and the
sound may be distorted. In this case, place the DVD/
VCR away from the TV, radio, or VCR.

Notes on moisture condensation

Moisture condensation damages the DVD/VCR.
Please read the following carefully.

Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the head drum or the optical
pick-up lens inside this unit, one of the most crucial
internal parts of the DVD/VCR.

Moisture condensation occurs during the
following cases.

When you bring the DVD/VCR directly from a cold
place to a warm place.
When you use the DVD/VCR in a room where you
just turned on the heater, or a place where the cold
wind from the air conditioner directly hits the unit.
In summer, when you use the DVD/VCR in a hot and
humid place just after you move the unit from an air
conditioned room.
When you use the DVD/VCR in a humid place.

f

o

m

e

o

l

p

i

s

m

a

x

E

n

o

c

t

u

r

e

s

n

a

e

t

i

d

o

n

!

Tape

Head drum

It’s too

warm!

Notes on cleaning

Use a soft, dry cloth for cleaning.

For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the
DVD/VCR.
If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.

To obtain a clear picture

The DVD/VCR is a high technology, precision device. If
the video head, the head drum, the optical pick-up lens
or disc drive parts are dirty or worn down, the picture
quality will deteriorate. To obtain a clear picture, we
recommend regular inspection and maintenance
(cleaning or parts replacement) every 1,000 hours of
use depending on the operating environment. For
details, contact your nearest dealer.

6

2C51701A (E)p02-13 19/05/2003, 10:346

Do not use the DVD/VCR when moisture
condensation may occur.

If you use the DVD/VCR in such a situation, it may
damage discs and internal parts. Remove the disc or
the video tape, connect the power cord of the DVD/
VCR to the wall outlet, turn on the DVD/VCR, and
leave it for two or three hours. After two or three
hours, the DVD/VCR will have warmed up and
evaporated any moisture. Keep the DVD/VCR
connected to the wall outlet and moisture
condensation will seldom occur.

Wait!

Wall outlet

Notes on discs

On handling discs

Do not touch the playback side of the disc.

Playback side

Do not attach paper or tape to discs.

On cleaning discs

Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.

Structure of disc contents

Normally, DVD video discs are divided into titles, and
the titles are sub-divided into chapters. VIDEO CDs and
audio CDs are divided into tracks.

DVD video disc

DVD video disc

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3

Video CD/Audio CD

Video CD/Audio CD

Track 1 Track 2 Track 3 Track 4 Track 5

Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
There may be discs that do not have these numbers.

Introduction

If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.

On storing discs

Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.

Notes on copyright

It is forbidden by law to copy, broadcast, show,
broadcast on cable, play in public, and rent copyrighted
material without permission.

This device does not tape-record copy protected DVD
Video Discs.
The device is not to be used for copying copyrighted
content without the express written permission of the
copyright owner.
Obtaining such permission is the sole responsibility of
the user.

This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.

2C51701A (E)p02-13 19/05/2003, 10:347

7

Introduction

Recordable

ReWritable

Notes on discs (continued)

About this owner’s manual

This owner’s manual explains the basic instructions of
this DVD/VCR. Some DVD video discs are produced in
a manner that allows specific or limited operation during
playback. As such, the DVD/VCR may not respond to all
operating commands. This is not a defect in the DVD/
VCR. Refer to instruction notes of discs.

” may appear on the TV screen during operation.

“

” means that the operation is not permitted by the

A “
DVD/VCR or the disc.
For example, sometimes it is unable to stop the
playback of copyright message of the disc when the
STOP (3) button is pressed. Alternatively, the “

” may

also indicate that the feature is not available for the disc.

Notes on region numbers

The region number of this DVD/VCR is 1. If region
numbers, which stand for their playable area, are printed

ALL

1

or

on your DVD video disc and you do not find

,
disc playback will not be allowed by the player. (In this
case, the DVD/VCR will display a message on-screen.)

On Video CDs

This DVD/VCR supports Video CDs equipped with the
PBC (Version 2.0) function. (PBC is the abbreviation of
Playback Control.) You can enjoy two playback
variations depending on types of discs.

• Video CD not equipped with PBC function

(Version 1.1)

Sound and movie can be played on this DVD/VCR in
the same way as an audio CD.

• Video CD equipped with PBC function

(Version 2.0)

In addition to operation of a Video CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s
manual may not work with some discs.

Playable discs

This DVD/VCR can play the following discs.

Maximum

playback time

Approx. 4 hours

(single sided disc)

Approx. 8 hours

(double sided disc)

Approx. 80 minutes

(single sided disc)

Approx. 160 minutes

(double sided disc)

Approx. 74 minutes

Approx. 20 minutes

Approx. 74 minutes

Approx. 20 minutes

Depending

on the

recording

conditions

file

Disc
Size

12 cm

+

8 cm

12 cm

+

8 cm

12 cm

8 cm

(CD

single)

12 cm

8 cm

DVD
video
discs

Video
CDs

Audio
CDs

CD-R/
CD-RW

Disc Mark

DIGITAL VIDEO

Contents

Audio
Video

(moving

pictures)

Audio
Video

(moving

pictures)

Audio

CD-DA/

JPEG/

MP3/WMA

• This unit can play back FUJICOLOR CD and Kodak
Picture CD formats.

• You cannot play discs other than those listed above.

• You cannot play discs of DVD-RAM, DVD-RW, Photo
CD, etc., or non standardized discs even if they may
be labeled as above.

• Some CD-R/RWs can not be played back depending
on the recording conditions.

• This DVD/VCR uses the NTSC color system, and
cannot play DVD video discs recorded in any other
color system (PAL, SECAM, etc.).

8

2C51701A (E)p02-13 19/05/2003, 10:348

Contents

Introduction

IMPORTANT SAFEGUARDS ..........................2

Power source ...................................................5

Precautions ......................................................6

Notes on discs..................................................7

Contents...........................................................9

Identification of controls .................................10

Connections

Antenna connections......................................14

CATV (CABLE TV) connections.....................16

Connecting to a TV ........................................18

Connecting to optional equipment..................20

Basic setup

Setting the video channel............................... 22

Setting the language ...................................... 23

Clock setting................................................... 24

Tuner setting .................................................. 27

Playback (VCR)

Loading and unloading a cassette tape ......... 29

Cassette tape playback.................................. 30

Special playback ............................................ 31

Convenience function..................................... 32

Recording (VCR)

Recording a TV program................................ 34

One-touch Timer Recording (OTR) ................ 36

Timer recording .............................................. 37

Other functions (VCR)

Basic playback (DVD)

Playing a disc ................................................. 42

Advanced playback (DVD)

MP3/WMA/JPEG playback ............................ 45

Zooming ......................................................... 50

Locating desired scene .................................. 50

Marking desired scenes ................................. 51

Repeat playback ............................................ 52

A-B Repeat playback ..................................... 52

Program playback (CD).................................. 53

Random playback (CD).................................. 53

Changing angles ............................................ 54

Title selection ................................................. 54

DVD menu...................................................... 54

Function setup (DVD)

Changing soundtrack language ..................... 55

Setting surround sound .................................. 55

Setting subtitles.............................................. 56

Karaoke playback........................................... 56

Setting the aspect ratio of TV screen ............. 57

Setting on screen display............................... 58

Status display of disc ..................................... 58

Dynamic Range Control ................................. 59

Parental control setting .................................. 60

To change the parental level.......................... 61

Temporary disabling of rating level by DVD disc ..

Setting setup language .................................. 63

Setting menu language .................................. 64

Changing subtitle language............................ 65

Setting audio soundtrack language................ 66

Selecting PROGRESSIVE scan..................... 67

62

Introduction

Stereo recording and playback ...................... 39

Second audio program (SAP) ........................ 39

Duplicating a video tape................................. 40

Recording a DVD/CD disc.............................. 41

2C51701A (E)p02-13 19/05/2003, 10:349

Others

Language code list ......................................... 68

Before calling service personnel .................... 69

Specifications ................................................. 70

LIMITED WARRANTY ................................... 71

9

Introduction

11

5

Identification of controls

See the page in for details.

Front panel

Cassette loading slot

EJECT button

29

ON/STANDBY

22

button

AUDIO (L/R)/VIDEO IN
(LINE IN 2) jacks

40

Rear panel

REC button

29

DVD indicator

VCR indicator

34

Remote sensor

22

13

Display window

CHANNEL M/? buttons

VCR/DVD mode selector button

42

STOP button

30

PLAY button

34

REW (Rewind) button

22

OPEN/CLOSE button

Disc tray

42

FF (Fast Forward)
button

30

30

30

42

When connecting the optical digital cable, remove
the cap and fit the connector into the jack firmly.
When not using the jack, keep the cap inserted
to protect it from dust intrusion.

DVD OPTICAL DIGITAL AUDIO
OUT jack (dust protection cap)

DVD S-VIDEO

OUT jack

19

S-VIDEO/COMPONENT
Video selector switch

19

10

2C51701A (E)p02-13 19/05/2003, 10:3410

DVD COAXIAL DIGITAL

20

AUDIO OUT jack

DVD AUDIO (L/R)
OUT jacks

19

DVD COMPONENT
OUT jacks

19

20

AC power cord

DVD/VCR common AUDIO
(L/R)/VIDEO OUT jacks

AUDIO (L/R)/VIDEO
IN (LINE IN1) jacks

18

40

RF IN jack

RF OUT jack

14

14

Display window

Play indicator

VCR indicator (VCR)

Still indicator

Recording

indicator (VCR)

Track indicator (CD)

Tape loaded indicator (VCR)

Timer Recording indicator (VCR)

VCR operation status

Press CALL to display information on screen.
To cancel the display, press CALL again.

While watching TV

DAY OF THE WEEK

CLOCK

STEREO AND

SEPARATE

AUDIO

PROGRAM

(SAP)

AM

MON

8 : 47
STEREO SAP

CH 125

00 : 00 : 00 SP

REAL TIME COUNTER

CHANNEL

TAPE SPEED

Multifunctional indicator

Progressive indicator

While operating a tape

HI-FI STEREO

8:30AMMON

HI-FI

STEREO

OUTPUT SELECTION

Disc inserted indicator (DVD)

OPERATING
MODE

AUTO REPEAT

00 : 15 :12 SP

TAPE IN

Disc inserted
indicator (CD)

AM/PM indicator

VCR Icons

Recording :

Rec/Pause

Play :

Stop :

Eject :

Introduction

:

DVD/CD/VCD operation status

Each press of DISPLAY, the status display of the disc will appear on the screen and change as follows.

DVD

ELASPED

TIME

OPERATING

TRACK NO.

2C51701A (E)p02-13 19/05/2003, 10:3411

CD/VCD

Track 11/99

00:34:56 01:12:33

34:56 71:33

TOTAL
TIME

TOTAL
TIME

ELAPSED TIME

OPERATING MODE

Title 1/99

SOUNDTRACK NO.

1/8

Eng DolbyDigital

1/32

Eng

Chapter 1/999

00:34:56 01:12:33

1/9

TITLE NO.
CHAPTER NO.

ANGLE NO.
SUBTITLE NO.

11

Introduction

Identification of Controls (continued)

The instructions in this manual describe the functions on the remote control. See the page in for details.

Remote control

CALL button
DISPLAY button

24

58

VCR DVD selector button
Direct channel

selection buttons
Number buttons

28
45

INPUT SELECT button
PROGRESSIVE button
TV/VCR button

22

COUNTER RESET button
ANGLE button

SP/SLP button
PLAY MODE button

REC button
OTR button

TIMER REC button
PLAY button

REW button

SLOW button

MARKER button

ZERO RETURN button
JUMP button

VCR MENU button
SETUP button

Direction buttons

54

34

52

34
36

37

30

30

31

51

32

50

23

47

45

(///)

SET +/

-

buttons

Channel +/Ð buttons

23

34

40
67

22

32

VCR

CALL

DVD

DISPLAY

321

OPEN/CLOSE

654

79

ANGLE

SLOW

JUMP

SETUP

CH

Ð

8

TV/VCR

SP/SLP

PLAY MODE

TIMER REC

PLAY

STOP

MARKER

+

SET

ENTER

Ð

SET

AUDIO SELECT

AUDIO

SUBTITLE

A-B RPT

CLOCK COUNTER

INDEX

SKIP

FWDREW

PAUSE/STILL

TOP MENU RETURN

MENU

+

CH

CM SKIP

INPUT SELECT
PROGRESSIVE

COUNTER RESET

REC/OTR

ZERO RETURN

VCR MENU

CANCEL

EJECT

0

ATR

INDEX

+Ð

SKIP

ZOOM

) buttonPower (

EJECT button (VCR)

22

29

OPEN/CLOSE button (DVD)

ATR button
SUBTITLE button

AUDIO SELECT button
AUDIO button

31

56

39

55

CLOCK COUNTER button

INDEX + button
SKIP button

A-B RPT button

INDEX Ð button
SKIP button

FWD button

STOP button

PAUSE/STILL button

TOP MENU button

RETURN button

CM SKIP button
ZOOM button

*MENU button

ENTER button

33

44

52
33

44

30

30

31

54

57

31

50

54

23

42

33

CANCEL button

37

12

2C51701A (E)p02-13 19/05/2003, 10:3412

* MENU button

Use the MENU button to display the menu included on
many DVD video discs. To operate a menu, follow the
instructions in “DVD Menu.”

54

Inserting Batteries

Introduction

Slide the battery compartment
cover in the direction of the

1

arrow.

Battery precautions

The precautions below should be followed when using batteries in this device:

1.Use only the size and type of batteries specified.

2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
versed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.

3.

Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.

5.Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery
manufacturer’s directions.)

Install two “AAA” batteries
(supplied),

23

polarity diagram in the battery
compartment.

paying attention to the

Replace the compartment
cover.

Re-

Remote control basics

• Press POWER (

• Select your desired operating mode (DVD or VCR) using VCR DVD.

(DVD or VCR indicator on the front panel will show you which mode is selected.)

• Press CH + or CH – to move through the channels one channel at a time.

• The CH +/– (

• You can directly access specific channels using Number buttons.

• Each press of VCR DVD on the remote control, switches the screen between the VCR screen (VCR mode) and the
DVD screen (DVD mode).

Operation

• Aim the remote control at the remote sensor and press control buttons to
operate.

• Operate the remote control within 30° angle on either side of the remote
sensor, up to a distance of Approx. 7 meters.

) to turn the DVD VCR on or off.

/ ) and SET +/– ( / ) are also used to navigate on-screen menu system.

Approx. 7 meters

2C51701A (E)p02-13 19/05/2003, 10:3413

13

Connections

OUT

(TV)

IN

(ANT)

OUT

(TV)

IN

(ANT)

OUT

(TV)

IN

(ANT)

Antenna connections

If you are using an antenna system, follow these instructions. If you are a cable (CATV) subscr iber, skip ahead to page 16
for the proper connections.

Antenna to DVD/VCR connection

The DVD/VCR must be connected “between” the antenna and the TV. First, disconnect the antenna from the TV and
connect it to the DVD/VCR. Then connect the DVD/VCR to the TV . Below are 3 common methods of connecting an antenna
system to a DVD/VCR. Find the type of antenna system you are using and follow the connection diagram.

Combination VHF/UHF Antenna with 75 ohm Coaxial Cable

1

75 ohm Coaxial Cable

DVD/VCR

2

3

Note:

Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire

DVD/VCR

Matching Transformer 300 ohm Input 75

ohm output (not supplied)

300 ohm Twin Lead (Flat) Wire

Separate VHF and UHF Antennas

VHF

If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300 ohm inputs and
one 75 ohm output.

UHF

Combiner 75/300 ohm Inputs 75 ohm output

(not supplied)

300 ohm Twin Lead (Flat) Wire

75 ohm Coaxial Cable

DVD/VCR

Notes: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the antenna to

the DVD/VCR properly.

• For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an outdoor type
antenna is required.

• If you are not sure about the connection, please refer to qualified service personnel.

14

2C51701A (E)p14-17 19/05/2003, 10:3514

DVD/VCR to TV connection

After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and f ollo w the
connection diagram.

This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna
inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.

Connections

75 ohm Coaxial Cable (supplied)

Splitter 75 ohm Input

75/300 ohm outputs
75 ohm Coaxial Cable
(supplied)

(not supplied)

TV

VHF/UHF IN

TV

UHF

VHF

Note: If a VHF or UHF antenna is used,

set the TV/CATV menu option to
the “TV” mode.

TV with single 75 ohm VHF/UHF antenna
input

Note: If a VHF or UHF antenna is used,

set the TV/CATV menu option to
the “TV” mode.

TV with 300 ohm UHF and 75 ohm VHF
antenna inputs

Splitter 75 ohm Input
300 ohm outputs

75 ohm Coaxial Cable
(supplied)

2C51701A (E)p14-17 19/05/2003, 10:3515

(not supplied)

TV

UHF

VHF

Note: If a VHF or UHF antenna is used,

set the TV/CATV menu option to
the “TV” mode.

TV with 300 ohm UHF and 300 ohm VHF
antenna inputs

15

Connections

CATV (CABLE TV) connections

Many cable companies offer services permitting reception of extra channels including pa y or subscription channels. This
DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable company
supplied converter box, except for those premium channels which are intentionally scrambled. If you subscribe to a
premium channel which is scrambled, you must have a descrambler box for proper reception.

1

DVD/VCR

IN

Incoming Cable

Allows:*Recording of nonscrambled channels.

Use of the programmable timer.

*

Recording of one channel while watching another.

*

DVD/VCR

2

Incoming

Allows:*Recording of channels through the converter box

Prevents:*Recording one channel while watching another.

Converter/
Descrambler

Cable

(scrambled and unscrambled).
Using the programmable timer to record only the

*

channel selected at the converter box.

Using the DVD/VCR tuner to select channels.

*

(ANT)

OUT
(TV)

IN

(ANT)

OUT
(TV)

TV

VHF/UHF

IN (ANT)

TV

VHF/UHF
IN (ANT)

Note:

To record from converter/descrambler,
DVD/VCR tuner must be tuned to the con­verter output channel, usually channel 3
or 4.

DVD/VCR

3

IN

Incoming Cable

Allows:*Recording of nonscrambled channels.

Use of the programmable timer.

*

Recording an unscrambled channel while watching

*

any channel selected at the converter box.

Prevents: Recording scrambled channels.

Note: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to the output of

the Converter/Descrambler box, usually channel 3 or 4.

(ANT)

OUT

(TV)

Converter/Descrambler

Note:

If you are playing a tape or using the tuner
built into the DVD/VCR, the converter must
be set to the video channel output of the
DVD/VCR (either 3 or 4).

16

2C51701A (E)p14-17 19/05/2003, 10:3516

VHF/UHF

IN (ANT)

TV

IMPORTANT: Make sure the TV/CATV menu option is set to the “CATV” mode.

This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scram­bled programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Con­sult your local cable company for more information concerning connection to their descrambler equipment. There are
many ways to connect your DVD/VCR to a cable system. Below are six common methods of connection.

DVD/VCR

4

Incoming Cable

Splitter

Converter/Descrambler

IN

(ANT)

OUT
(TV)

A/B Switch

A
B

TV

VHF/UHF
IN (ANT)

Allows:*Recording of one channel while watching another.

Using the programmable timer to record only the channel selected at the converter box.

*

Recording of all channels through the converter box.

*

Prevents:*Watching scrambled channels while recording another channel.

Using the DVD/VCR tuner to select channels.

*

DVD/VCR

5

Splitter

Incoming Cable

Converter/Descrambler

IN

(ANT)

OUT
(TV)

A/B Switch

A
B

TV

VHF/UHF

IN (ANT)

Connections

Allows:*Recording of nonscrambled channels.

Recording of one channel while watching another.

*

Watching premium channels through the conver ter while recording nonscrambled channels.

*

Using the programmable timer.

*

Prevents: Recording scrambled channels.

DVD/VCR

6

Splitter

Incoming Cable

Converter/Descrambler

Converter/Descrambler

IN

(ANT)

OUT
(TV)

Allows:*Recording of all channels through the converter box.

Recording a scrambled or unscrambled channel while watching another (scrambled or

*

unscrambled) channel.
Using the programmable timer to record only the channel selected at the converter box.

*

Prevents: Using the DVD/VCR tuner to select channels.

A/B Switch

A

B

TV

VHF/UHF
IN (ANT)

17

2C51701A (E)p14-17 19/05/2003, 10:3517

Connections

Connecting to a TV

Connect the DVD/VCR to your TV.

Note: This method transports VHS and DVD-video signals. For enhanced DVD-video performance, we recommend you

also connect the S-video or ColorStream® component video outputs to your TV/monitor. (see page 19.)

Connecting to a TV

Signal flow

(red) (white)

(yellow)

To wall outlet

T o VIDEO

OUT

To video input

Notes:

• Refer to the owner’s manual of the connected TV as well.

• When you connect the DVD/VCR to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.

• If your television set has one audio input, connect the left and right audio outputs of the DVD/VCR to a Y cable adapter (not
supplied) and then connect to your TV.

• Connect the DVD/VCR directly to your TV. If you connect the DVD/VCR to a VCR, TV/VCR combination or video selector, the
playback picture may be distorted as DVD video discs are copy protected.

To ANALOG AUDIO OUT

Audio/video cable (supplied)

To audio inputs

(yellow)

TV or monitor with
audio/video inputs

(red)

(white)

18

2C51701A (E)p18-25 19/05/2003, 10:3518

S-video output/input

An S-Video connection is superior to Video (Yellow) output. Use this method for DVD playback when the connected television has S­Video input, and does not have component video inputs.

Component video outputs/inputs

PROGRESSIVE outputs/inputs

Some TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively scanned video
signal. Connenting to these inputs allows you to view the highest quality pictures with less flicker.

INTERLACED outputs/inputs

Some TVs or monitors are equipped with component video inputs. Connecting to these inputs allows you to enjoy the highest quality
DVD picture playback.

Notes:

• Actual labels for component video inputs may vary depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)

• In some TVs or monitors, the color levels of the playback picture may be reduced slightly or the tint may change. In such a
case, adjust the TV or monitor for optimum performance.

Connecting to an audio system and TV equipped with S-video input/component video inputs

Note: The S-video output and component video output transports the DVD-video signal exclusively and will deliver

enhanced DVD video picture performance.

Signal flow

(white)

To ANALOG
AUDIO OUT

(red)

When you make this connection, set the S-VIDEO/
COMPONENT Video selector switch to the desired
position.
And also you must select the corresponding video
input on your TV.

Audio cable (not supplied)

To audio inputs of

To S­VIDEO
OUT

To PR/CR
VIDEO
OUT

To PB/CB
VIDEO
OUT

To wall outlet

To Y
VIDEO
OUT

Component video
cable (not supplied)

the amplifier

To
To

To Y video input

PB/CB

video input

PR/CR

video input

(red)

(white)

Connections

To S-video input

S-video cable (not supplied)

If you connect the DVD/VCR to your TV
with the DVD OUT jacks, select the

TV or monitor with
ColorStream

®

component video inputs

Audio system

corresponding video input on your
television to watch DVD video discs.

Notes:

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.

• If you place the DVD/VCR near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD/
VCR away from the tuner and radio.

• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening
level. Otherwise, the speakers may be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, the
speakers may be damaged.

• When connecting to a TV using the Video or S-video jack, make sure that the Progressive indicator on the display

window is not lit. If it is lit, the Video and S-video outputs do not feed the correct signals and you cannot see any
picture. To turn off the Progressive indicator, Select PROGRESSIVE scan Off (see page 67).

2C51701A (E)p18-25 19/05/2003, 10:3519

19

Connections

Connecting to optional equipment

You can enjoy high quality dynamic sounds of DVD video discs or audio CDs by
connecting the DVD/VCR to optional audio equipment.

For connection to your TV, see “Connecting to a TV”

Connecting to an amplifier equipped with a Dolby Digital decoder

18 19

.

: Front speaker
: Rear speaker
: Sub woofer

: Center speaker
: Signal flow

Dolby Digital

Dolby Digital is the surround sound technology used in theaters showing the latest movies,
and is now available to reproduce this realistic effect in the home. You can enjoy motion
picture and live concert DVD video discs with this dynamic realistic sound by connecting the
DVD/VCR to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digital
processor. If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of
Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital
soundtracks, as well as from titles with the Dolby Surround mark.

Manufactured under license from Dolby
Laboratories. “Dolby” “Pro Logic” and the
double-D symbol are trademarks of
Dolby Laboratories. Confidential
unpublished works. ©1992-1997 Dolby
Laboratories. All rights reserved.

• Use DVD video discs encoded via
the Dolby Digital recording

Amplifier equipped with a
Dolby Digital decoder

To COAXIAL

type digital

audio input

To OPTICAL
type digital
audio input

Optical digital cable

75 Ω coaxial cable

Connect either.

system.

Connecting to an amplifier equipped with Dolby Pro Logic Surround

Dolby Pro Logic Surround

You can enjoy the dynamic realistic sound of Dolby Pro Logic Surround by connecting an amplifier and speaker system (right and left
front speakers, a center speaker, and one or two rear speakers).

With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an amplifier
equipped with a Dolby Digital decoder.” Refer to that amplifier’s owner’s manual and set
the amplifier so you can enjoy Dolby Pro Logic Surround sound.

With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.

*

Amplifier equipped with
Dolby Pro Logic Surround

To audio input

T o ANALOG

AUDIO OUT

Audio cable

* Connect one or two rear speakers.
The output sound from the rear speakers
will be monaural even if you connect two
rear speakers.

Connecting to an amplifier equipped with a DTS decoder

Digital Theater Systems (DTS)

DTS is a high quality surround technology used in theaters and now available for home use,
on DVD video discs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTS
encoded sound tracks on DVD video discs or audio CDs.

Amplifier equipped with
a DTS decoder

To COAXIAL

type digital
audio input

To OPTICAL
type digital
audio input

Optical digital cable

75 Ω coaxial cable

20

2C51701A (E)p18-25 19/05/2003, 10:3520

Connect either.

“DTS” and “DTS Digital Surround” are
trademarks of Digital Theater Systems,
Inc.

• Use DVD video discs or audio
CDs encoded via the DTS
recording system.

Warning

When playing DTS-encoded discs (D VD/VCR), excessive noise ma y be output from the analog stereo jacks. To avoid possible
damage to the audio system, you should take proper precautions when the ANALOG AUDIO OUT (L/R) jacks of the DVD/
VCR are connected to an amplification system. To enjoy DTS Digital Surround™ playback, an external 5.1 channel DTS
Digital Surround™ decoder system must be connected to the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR.

Connecting to an amplifier equipped with an MPEG2 audio decoder

MPEG2 sound

You can enjoy motion picture and live concert DVD video discs with dynamic
realistic sound by connecting an amplifier equipped with an MPEG2 audio decoder
or MPEG2 audio processor.

• Use DVD video discs encoded via
the MPEG2 recording system.

Amplifier equipped with an
MPEG2 audio decoder

To COAXIAL

type digital

audio input

To OPTICAL
type digital
audio input

Optical digital cable

Connect either.

75 Ω coaxial cable

Connecting to an amplifier equipped with a digital audio input

2 channel digital stereo

You can enjoy the dynamic sound of 2 channel digital stereo by connecting an
amplifier equipped with a digital audio input and speaker system (right and left front
speakers).

Connections

Amplifier equipped with
a digital audio input

To COAXIAL

type digital

audio input

To OPTICAL
type digital
audio input

Optical digital cable

Connect either.

75 Ω coaxial cable

Notes:

• DO NOT connect the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR to the AC-3 RF input of a Dolby Digital Receiver.
This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the BITSTREAM/PCM AUDIO
OUT jack of the DVD/VCR.

• Connect the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR to the “OPTICAL” or “COAXIAL” input of a Receiver or
Processor.

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.

• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening
level. Otherwise, the speakers may be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, the
speakers may be damaged.

2C51701A (E)p18-25 19/05/2003, 10:3521

21

Basic setup

Setting the video channel

When a TV is connected with the 75 ohm coaxial cable only.

To view playback of a recorded tape or DVD disc, or to watch a
program selected by the VCR's channel selector, the TV must be set to
channel 3 or 4 (video channel).

Setting the video channel

Press and hold 3 or 4 on the remote for 3
seconds in standby mode.

1

OR

3 4

Press POWER to turn on the DVD/VCR.

2

The video channel will
start to flash for 3
seconds in the display
window.

Notes:

• If the unit does not operate properly , or No key operation

• During the DVD playback if you change the operating mode

POWER
3

4
TV/VCR
VCR DVD

For a push-button TV tuner

If CH 3 or 4 corresponding to the video channel cannot
be tuned on your TV, proceed as follows: set the VCR
3/4 channel selector and the TV to CH 3 or 4, play
back a prerecorded tape and tune the TV to receive a
sharp color picture from the video cassette recorder.
Refer to your TV owner's manual for details.

(by the unit and/or the remote control): Static electricity,
etc., may affect the player's operation. Disconnect the AC
power cord once, then connect it again.

from DVD to VCR, the DVD will continue to play back the disc
and stop after about 5 minutes.

Press VCR DVD selector to select the VCR mode.

3

4

VCR
DVD

Turn ON the TV and set to CH 3 or 4 to corre­spond with the channel selected in step 1.

Press TV/VCR to select the VCR position.

The VCR indicator on the
front panel will light.

5

TV/VCR

Select any channel to receive a TV station in your area.
The channel number will appear on the screen for

6

about 4 seconds.

The VCR indicator will
appear in the display
window.

22

2C51701A (E)p18-25 19/05/2003, 10:3522