ORION ELECTRIC M2C5A Users Manual
Instant Timer Recording (ITR)
The Instant Timer Recording
feature provides a simple and
convenient way to make a timed
recording.
Preparation:
Turn ON the TV and set it to the video input mode.
•
•
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press VCR to select the VCR mode. (The VCR indicator
will light.)
Example: Instant Timer Recording for 30 minutes.
Load a cassette tape with the erase
1
prevention tab intact.
The VCR will automatically turn on.
Press SP/EP to select the desired tape
2
speed SP or EP.
The tape counter and “SP” or “EP” will
appear on the screen for about 4
seconds.
Set the TV/CATV option to the appropriate position (see page
3
21).
TV - VHF/UHF channels
CATV - CABLE TV channels
00 : 00 : 00 SP
NOTE:
If you wish to watch the DVD playback
during the ITR, press DVD to change to
DVD mode and perform the DVD playback (see page 39).
Press Number keys or VCR CH +/– to
4
select the channel to be recorded.
Press REC on the VCR or while holding REC, press PLAY on
5
the Remote to begin recording. Press REC on the VCR again to
stop recording after 30 minutes. Each additional press of REC
will increase recording time as shown in the chart below, up to a
maximum of 6 hours. The ITR and recording time will appear on
the screen for about 4 seconds. And, REC will keep blinking in
the display.
Press
once
twice
3 times
4 times
5 times
Recording time
NORMAL REC
0:30
1:00
1:30
2:00
Press
6 times
7 times
8 times
9 times
10 times
Recording time
3:00
4:00
5:00
6:00
NORMAL REC
INDEX
To cancel ITR
Press STOP or turn off the power.
” will appear on screen for about 4
“
seconds.
CH 110
ITR 0 : 30
CH 125
32
2C51201AE(30-35) 15/3/03, 11:15 AM32
Timer recording
Timer recording can be programmed
on-screen with the remote control.
The built-in timer allows automatic
unattended recording of up to 8
programs within 1 month.
Preparation:
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
•
Then press VCR to select the VCR mode.
Load a cassette tape with the erase prevention tab intact.
•
Press OSD to verify time and date are correct (see page 31).
•
Example: Program a timer recording for the 26th day, channel 125
(CATV), 11:00 - 11:30 PM on timer program number 1 (Tape speed: EP).
Press SET UP MENU. Select the
1
TIMER REC SET option, then press
ENTER.
Press SET + or – to select one of the
2
program line, then press ENTER.
Press SET + or – to select the date,
3
then press ENTER.
MENU
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
á
+/Ð/ENTER/MENU
DATE START END CH
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
á+/Ð
/ENTER/CANCEL/MENU
DATE START END CH
26(SU)
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
á+/Ð
/ENTER/CANCEL/MENU
ON OFF
ON OFF
ñ
Ð:ÐÐ Ð:ÐÐ ÐÐÐ
Ð
Ð
Ð
Ð
Ð
Ð
Ð
Ð
ñ
Ð
Ð
Ð
Ð
Ð
Ð
Ð
Ð
ñ
NOTES:
•
If the clock symbol ( ) blinks when
the timer recording ended, the TV
program has not been completely
recorded because of an insufficient
tape supply. In this case, press TIMER
to cancel the timer program or press
EJECT to remove the cassette tape.
•
During timer recording standby mode,
the VCR mode cannot be selected. To
use the VCR, press TIMER at first,
then press VCR to change to VCR
mode. After you use the VCR, press
TIMER again to put the VCR into timer
recording standby mode.
•
If you press TIMER during timer
recording, the recording operation will
be interrupted. If you press TIMER
again within the programmed time, the
recording operation will start again.
•
After a power failure or disconnection
of the power plug, all programmed
recording settings and time display
will be lost upon resumption of power.
In this case, reset the clock (see pages
23-25) and reprogram any timer
recordings.
Set the start time, end time, channel
4
and tape speed as in step 3.
NOTES:
If the programmed start time is over the
•
present time, the program will be canceled
after pressed ENTER.
•
Press CANCEL to move cursor backward for correction.
•
To record from external source set the channel to “L”. “L” will appear
DATE START END CH
26(SU)11:00PM11
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
á+/Ð
/ENTER/CANCEL/MENU
next to CH 125 (or 69).
To enter other programs, repeat step
5
2 through 4.
• To return to the normal screen,
press SET UP MENU twice.
Press TIMER. The clock symbol ( ) will appear on the
6
display and the VCR stands by for recording. At the same
DATE START END CH
26(SU)11:00PM11
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
á+/Ð
/ENTER/CANCEL/MENU
time, VCR mode will change to DVD mode automatically. You
can use DVD even if the VCR is in the timer recording mode.
If you do not use the DVD, turn the power off.
The timer recording will start at 5 seconds before the time you
predetermined.
NOTES:
•
If the clock symbol (
) does not appear on the display in spite
of the pressing of TIMER, the cassette may not have been
loaded yet (see page 26).
•
If the cassette is ejected in spite of the pressing of TIMER , the
erase prevention tab of the cassette may have been removed
(see page 26).
:30PM125
:30PM125
ñ
ñ
EP
Ð
Ð
Ð
Ð
Ð
Ð
Ð
EP
Ð
Ð
Ð
Ð
Ð
Ð
Ð
33
2C51201AE(30-35) 15/3/03, 11:15 AM33
Timer-recording
Timer recording special case
Weekly (e.g. WKL-TU: each Tuesday) or daily (e.g.
MO-SA: Monday to Saturday) timer recording
Follow the procedure of timer recording on the previous
page. At picture 3 press SET + or – repeatedly until the
desired setting appears. Then press ENTER.
When you press SET – repeatedly, the indicator at
DATE will change as follows, in this case the today is
Friday.
The current day (Friday) SU-SA (Sunday to Saturday)
One month later
minus one day
WKL-WE WKL-TH (Weekly Thursday)
(Weekly Wednesday)
á+/Ð
MO-SA (Monday to Saturday)
MO-FR (Monday to Friday)
DATE START END CH
Ð:ÐÐ Ð:ÐÐ ÐÐÐ
WKL-WE
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
/ENTER/CANCEL/MENU
Ð
Ð
Ð
Ð
Ð
Ð
Ð
Ð
ñ
Confirmation / Cancellation of the timer
recording
If the timer has been activated, press TIMER to
1
deactivate the timer. The clock symbol (
disappear. Then press VCR to change to VCR
mode.
To confirm timer program:
2
At picture 1 on the
previous page select the
“TIMER REC SET” option
and press ENTER.
Then the timer program
list as right will appear on
the screen.
To cancel timer program:
3
Press SET + or – to
select the unnecessary
program, then press
CANCEL to cancel the
program.
DATE START END CH
26(SU)11:00PM11
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
á+/Ð
/ENTER/CANCEL/MENU
DATE START END CH
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
á+/Ð
/ENTER/CANCEL/MENU
:30PM125
) will
EP
Ð
Ð
Ð
Ð
Ð
Ð
Ð
ñ
Ð
Ð
Ð
Ð
Ð
Ð
Ð
Ð
ñ
In case timer programs-overlap
•
Do not overlap timer programs as portions of the
conflicting programs will be lost. The first recording
time has priority over the next recording time as shown
in the diagram below.
Program 1
Program 2
Program 3
Recording
Control Settings
8 : 00
NOTES:
•
The daily/weekly recording can be made continuously until the recording is canceled or the tape
reaches the end.
•
During timer recording the automatic rewinding
mechanism does not function.
Prog.1
9 : 00
Deleted Parts
Non Recorded Portion Parts
Prog.2 Prog.3
10 : 00
11 : 00
Press SET UP MENU repeatedly until the TV-picture
4
appears.
NOTES:
•
If there are other timer record programs remaining,
TIMER must be pressed to reactivate the timer,
otherwise the remaining timer record programs will
be ignored.
•
You cannot confirm the timer program during timer
recording operation.
•
You can also correct the programmed setting in
program confirm mode.
At step 2 above, press ENTER to enter the program
input mode. Then press ENTER repeatedly until the
item you wish to correct
blinks. Then correct the data
with SET + or –.
Then press SET UP MENU
repeatedly until the TVpicture appears.
DATE START END CH
26(SU)11:00PM11
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
РРРРРР Ð:ÐÐ Ð:ÐÐ ÐÐÐ
á+/Ð
/ENTER/CANCEL/MENU
:30PM125
ñ
EP
Ð
Ð
Ð
Ð
Ð
Ð
Ð
34
2C51201AE(30-35) 15/3/03, 11:15 AM34
Stereo recording and playback/Separate Audio Program (SAP)
SAP
Stereo Recording and Playback
The VHS Hi-Fi audio system permits high fidelity recording of MTS
STEREO TV broadcasts.
When a MTS STEREO broadcast is
received, the word “STEREO” will appear
on the screen for about 4 seconds
and the program can be viewed or recorded in stereo.
The Hi-Fi STEREO recording procedure
is the same as for normal recordings.
NOTE:
When using a CATV system, stereo TV programs may be transmitted
over a mono cable channel. In this case the word “STEREO” will not
appear and the sound will be in mono.
Output selection
When viewing an MTS STEREO TV program, or playing a prerecorded
VHS Hi-Fi STEREO videotape, press A.MONITOR to select how the
audio will be heard through the speakers. Normally set to the Hi-Fi
STEREO position, this button can be set to the MONO position if the
stereo broadcast or videotape audio is of poor quality. The “R” and “L”
positions allow the audio from the Right or Left Hi-Fi channel to be heard
over both TV speakers. This button has no effect when viewing a MONO
videotape or TV program. Each time when you press the button, OUTPUT
SELECTION display appears on the screen for several seconds. Refer
to the chart below.
STEREO
NOTES:
• When playing back a tape that is not
recorded in Hi-Fi stereo mode, the
audio will automatically be monaural.
• When listening to a VHS Hi-Fi video
tape or MTS broadcast through the
VHF/UHF jack (Audio/Video cable not
connected), the sound will be
monaural.
OUTPUT
SELECTION
STEREO
L ch
R ch
MONO
SOUND HEARD ON BOTH
SPEAKERS
STEREO
LEFT CHANNEL AUDIO
RIGHT CHANNEL AUDIO
MONO
Separate Audio Program (SAP)
Your VCR is fitted with a SAP broadcast system which enables
you to switch to a separate audio program when viewing a
selected channel.
This function applies only when the program is broadcast in
multi-languages through the SAP broadcast system.
Press SET UP MENU. Then press or to select “SAP”.
1
Then press ENTER to select “ON”.
2
Then press SET UP MENU until
the menu screen is cleared.
Listening to SAP
When the VCR is turned on or a channel selection is made, make
certain the letters “SAP” appears on the screen for about 4 seconds.
This means that the “Separate Audio Program” broadcasting is
available.
STEREO SAP
OR
MENU
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
á
+/Ð/ENTER/MENU
ON OFF
ON OFF
ñ
35
2C51201AE(30-35) 15/3/03, 11:15 AM35
Duplicating a video tape/Duplicating a disc material onto a video tape
Duplicating a video tape
If you connect the VCR to another VCR or camcorder, you can duplicate a previously recorded tape.
Make all connections before turning on the power.
Load a blank cassette tape with the erase preven-
1
tion tab intact into the recording VCR.
Load a previously recorded tape into the playback
VCR or CAMCORDER.
Press SP/EP to select the desired tape speed SP
2
or EP.
It is recommended that you set the speed to the
SP mode on the recording VCR for best results.
Press VCR CH + or – to select AUDIO/VIDEO input
3
position. “L” will appear in the
display.
Connection with second VCR
Playback VCR
To VIDEO OUT
AUDIO/VIDEO cable (supplied)
Recording VCR
To AUDIO (R) OUT
To AUDIO (L) OUT
Press REC on the recording VCR or on the Remote.
4
While holding REC, press PLAY.
Then press PAUSE.
Press PLAY button on the playback VCR or
5
CAMCORDER, then press PAUSE button.
Press PAUSE on both the VCRs simultaneously to
6
begin the duplicating process.
Connection with Camcorder
Playback Camcorder
To AV Jack
Recording VCR
To AUDIO (R) IN
To AUDIO (L) IN
AUDIO/VIDEO cable (not supplied)
To VIDEO IN
To AUDIO (R) IN
To AUDIO (L) IN
T o VIDEO IN
For duplicating a previously recorded tape from a
camcorder, follow the camcorder manufacturer’s
instructions. A typical camcorder dubbing hookup
is shown above.
Duplicating a disc material onto a video tape
You can record disc material in DVD, Video CD, Audio CD, etc. onto a video tape with this DVD/VCR only.
If the DVD disc has a Copy-guard feature, the duplicating is not possible. A symbol mark “ ” will
appear on the screen for approx. 4 seconds. See page 39 for more information about the DVD playback.
Preparation:
Load a cassette tape with the erase prevention tab
•
intact.
•
Select the tape speed (SP or EP) in the VCR mode.
•
Load a disc you wish to duplicate.
Press DVD to select the DVD mode. (The DVD
1
indicator will light.)
Press PLAY to start the disc playback.
2
During disc playback, press REC on the VCR or
3
while holding REC, press PLAY on the Remote.
The duplicating will start.
NOTES:
• You can set the duplicating time using the ITR-function.
At step 3 above press REC repeatedly until the desired
duplicating time appears on the screen (see page 32).
• When the scanning mode is set to the progressive
mode, you cannot duplicate a disc material onto a video
tape. When REC is pressed, the PROGRESSIVE
indicator “
“PLEASE SET
” on the display window will flash and
OFF” will appear on the screen.
36
2C51201AE(36-41) 15/3/03, 11:15 AM36
The following types of discs can be played on this unit.
Disc type and logo mark
DVD Video
Video CD
Audio CD
CD-R/CD-RW
Recordable
ReWritable
Recorded content
Audio
+
Video
Audio
CD-DA/JPEG/
MP3/WMA file
Disc size
5 inches
(12 cm)
3 inches
(8 cm)
5 inches
(12 cm)
3 inches
(8 cm)
5 inches
(12 cm)
3 inches
(8 cm)
5 inches
(12 cm)
3 inches
(8 cm)
Disc
• This unit can play back FUJICOLOR
CD and Kodak Picture CD formats.
• DVD-ROM, SVCD, CVD, Photo CD,
etc. cannot be played.
• Some CD-R/RWs can not be played
back depending on the recording
conditions.
• This unit is to be used exclusively with
the NTSC color system. PAL and
SECAM system discs cannot be used
with this unit.
Region Number
Region number (Regional restriction code) is built-in to the unit and DVD video discs.
Region number “1” or “ALL” of DVD video discs can be used on this unit.
Title
When two or more movies are recorded on a disc,
the disc is divided into two or more sections.
Each section is called a “TITLE”.
TITLE1 TITLE2
CHAPTER 1
CHAPTER 2 CHAPTER 2 CHAPTER 3CHAPTER 1
Chapter
The titles can be subdivided into many sections.
Each section is called a “CHAPTER”.
Video CD/Audio CD T rack
A V ideo CD or Audio CD can contain several items.
These are assigned to the tracks.
TRACK 1 TRACK 2 TRACK 3 TRACK 4 TRACK 5
Video CD/Audio CD
Removing Disc from Case
Be sure to hold the edge of disc. Do not touch the surface of the disc.
Pick up the disc gently from the case.
• Do not scratch the disc.
• Do not get dirt on the surface of the disc.
• Do not stick a label or adhesive tape on the disc.
• Do not drop or bend the disc.
Storing Disc
• Store the disc in the case to avoid risk of scratches, dirt or damage.
• Do not leave disc exposed to direct sunlight or in hot or humid places.
Cleaning Disc
Wipe the disc with a clean, dry cloth from center to edge.
• Do not wipe the disc round.
• Do not use liquid or aerosol cleaners.
1
DVD DISC
CD
2C51201AE(36-41) 15/3/03, 11:15 AM37
37
Setting setup language
Reading
The setup language can be selected.
Preparation:
Turn ON the TV and set it to the video input mode.
•
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
•
When using an amplifier, switch on the amplifier.
•
Press DVD to select the DVD
1
mode. (The DVD indicator will
light.)
“No Disc” will appear on the
screen. (If a DVD disc has already
loaded, the playback will start
automatically.)
Press SET UP MENU in the stop
2
mode. The SETUP MENU of
DVD will appear on the screen.
Then press or to select
“Other”.
Press or ENTER to select
3
“OSD Language”.
Picture ParentalSound
Language Other
/Enter/Setup/Return
Language
Picture ParentalSound
OSD Language English
Other
If the DVD/VCR does not operate
properly: Static electricity, etc., may
affect the player's operation. Disconnect
the AC power cord once, then connect
it again.
/Enter/Setup/Return
Press
4
press or to select desired
language (e.g. English), then
press ENTER.
NOTE: To make the SETUP screen disappear, press SET UP
or ENTER and then
MENU (or RETURN).
Language
Picture ParentalSound
OSD Language English English
/Enter/Setup/Return
Other
Francais
Espanol
38
2C51201AE(36-41) 15/3/03, 11:15 AM38
Playback procedure
Preparation:
Turn ON the TV and set it to the video input mode.
•
•
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Press OPEN/CLOSE.
1
The disc tray will open.
Place a disc onto the tray.
2
Hold the disc, position it with the
printed label side up, align it with
the guides, and place it in its
proper position.
Press OPEN/CLOSE or PLAY.
3
The disc tray closes automatically.
On the screen,
“Reading” and then playback will
commence.
• A menu screen may appear on
the TV screen, if the disc has
a menu feature. In this case,
press
ENTER to operate a menu
feature.
changes to
Reading
, , , or
Press STOP to end playback.
4
• The DVD/VCR memorizes the stopped point, depending on
the disc. “
” keep blinking in the display until the playback is stopped
“
completely. Press PLAY to resume playback (from the scene
point).
• If you press STOP again (“
the disc, the DVD/VCR will clear the stopped point.
Then press OPEN/CLOSE.
5
The disc tray opens.
Remove the disc and press POWER.
NOTES:
•
If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV
screen according to the type of loaded disc. In this case, check your disc again (see pages 37 and 52).
•
Some discs may take a minute or so to start playback.
•
A “Prohibition” symbol
tried is not available on the disc, or the DVD/VCR can not access the feature at this time. This does not indicate
a problem with the DVD/VCR.
•
When you set a single-faced disc label downwards (ie. the wrong way up) and press OPEN/CLOSE or PLAY,
“Reading” will appear and remain on the screen for approx. 40 seconds and then it will change to “Incorrect
Disc”.
•
Some playback operations of DVDs may be intentionally fixed by software producers. Since this DVD/VCR plays
DVDs according to the disc contents the software producers designed, some playback features may not be
available. Also refer to the instructions supplied with the DVDs.
•
When playing DTS-encoded Audio CDs, excessive noise will be heard from the analog stereo outputs. To avoid
possible damage to the audio system, the consumer should take proper precautions when the analog stereo
outputs of the DVD/VCR are connected to an amplification system.
may appear at the upper left of the screen. This symbol means either the feature you
The disc tray closes automatically and DVD/VCR turns off.
” appears on the screen for approx. 4 seconds.
” appears on the screen) or unload
39
2C51201AE(36-41) 15/3/03, 11:15 AM39
Special playback
Note: There may be a slight delay between pressing the button and the
function activation.
Fast Forward Playback
Press FF during normal playback.
Each press of FF will increase the speed of the search
(x4), (x8), (x20).
• To resume normal playback, press PLAY.
(x2),
Review Playback
Press REW during normal playback.
Each press of REW will increase the speed of the search (x2),
(x4), (x8), (x20).
• To resume normal playback, press PLAY.
Still Playback
Press PAUSE during normal
playback.
To resume normal playback, press
PLA Y.
NOTE:
The unit is capable of holding a still video
image or On screen display image on your
television screen indefinitely. If you leave
the still video image or On screen display
image displayed on your TV for an extended period of time, you risk permanent
damage to your television screen.
Projection televisions are very susceptible.
Frame Advance
Press PAUSE during still playback.
One frame is advanced each time
you press PAUSE.
To resume normal playback, press
PLA Y.
Slow-motion Playback
Press SLOW during
Each press of SLOW will change the speed of the slow x1/2, x1/4,
x1/6, x1/7.
• To resume normal playback, press PLAY.
• To resume the still playback, press PAUSE.
normal playback or still playback.
Locating a chapter or track
Press SKIP ( ) Forward or SKIP ( ) Reverse during play-
back to locate a chapter that you want to watch.
Each time you press the button, a chapter or track is skipped.
40
2C51201AE(36-41) 15/3/03, 11:15 AM40
Zooming/Locating desired scene
Jump Time
Title
Chapter
/Enter/0 9/Cancel/Jump
Preparation:
•
Turn ON the TV and set it to the video input mode.
•
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light.)
Zooming
This unit will allow you to zoom in on the frame image. You can
then make selections by switching the position of the frame.
Press ZOOM during playback.
1
The center part of the image will
be zoomed in.
Each press of ZOOM will change
the ZOOM
1.5) and 3 (x 2.0).
Press / or / to view a different part of the frame.
2
You may move the frame from the center position to UP, DOWN,
LEFT or RIGHT direction.
In the zoom mode press ZOOM repeatedly to return to a 1:1
3
view (
1 (x 1.3), 2 (x
Off).
1
2C51201AE(36-41) 15/3/03, 11:15 AM41
NOTES:
• Y ou can use the Pause, Slow , Search
or Skip feature in the zoom mode.
• In case of the Video-CD playback with
PBC, the SEARCH MODE does not
work.
Locating desired scene
Use the title, chapter and time recorded on the disc to
locate the desired point to play back.
To check the title, chapter and time, press OSD (see page 58).
Press SEARCH MODE during
1
playback or stop mode.
Press or to select the “Time”, “Title” or “Chapter”.
2
Press Number keys to change the number.
3
• If you input a wrong number, press CANCEL.
• Refer to the package supplied with the disc to check the
numbers.
Press ENTER.
4
Playback starts.
• When you change the title, playback starts from Chapter 1 of
the selected title.
• Some discs may not work in the above operation.
41
Repeat playback
A
B
A
Preparation:
Turn ON the TV and set it to the video input mode.
•
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
•
Then press DVD to select the DVD mode. (The DVD indicator will
light.)
Repeat playback of Title, Chapter and Track
Press PLAY MODE during playback or stop mode.
1
DVD
CD
Repeat
/Enter/Play Mode
Press ENTER once or twice to select “Chapter” or “Title”.
2
In case of CD, at first press
ENTER once or twice to select “Track” or “All”.
Repeat
/Enter/Play Mode
Press PLAY MODE again to make the screen disappear.
3
•
Press PLAY to start Repeat playback.
•
To resume normal playback, select Repeat “Off”.
:
DVD
:
Off
Chapter
Play Mode Off
Repeat Off
to select “Repeat” and then press
:
:
/Enter/Play Mode
CD
Play Mode Off
Repeat
:
:
/Enter/Play Mode
All
A-B Repeat Playback
A-B repeat playback allows you to repeat material between two
selected points.
Press REPEAT A-B during
1
playback.
The start point is selected.
NOTES:
•
Some discs may not work with the
repeat operation.
•
In A-B repeat mode, subtitles near
point A or B may not appear.
•
Repeat playback is not available in
multi-angle scenes.
•
You may not be able to set A-B Repeat, depending on the scenes of the
DVD.
•
A-B repeat does not work with an interactive DVD, MP3/WMA/JPEG-CD
and Video-CD with PBC.
Press REPEAT A-B again.
2
The end point is selected.
Playback starts at the point that
you selected. Playback stops at
the end point, returns to Point A
automatically, then starts again.
To resume normal playback press REPEAT A-B again.
“
” appears on the screen.
Off
42
2C51201AE(42-47) 15/3/03, 11:15 AM42
Program playback/Random playback (CD)
Repeat
1
2
3
4
5
6
7
8
9
10
11
12
Clear Program Playback
Play Mode
:
Program
:
Off
/Enter/0 9/Cancel/Play Mode
Clear Program Playback
235811
3116912
174710
Repeat
:
Off
Play Mode
:
Program
/Enter/0 9/Cancel/Play Mode
Clear
Program Playback
235811
3116912
174710
Repeat
:
Off
Play Mode
:
Program
/Enter/0 9/
Cancel
/Play Mode
Preparation:
Turn ON the TV and set it to the video input mode.
•
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
•
Then press DVD to select the DVD mode. (The DVD indicator will
light.)
Program playback
You can arrange the order of tracks on the disc.
Press PLAY MODE in the stop
1
mode.
Press ENTER repeatedly until
2
the Program table as right
appears.
Example: In case you wish to
3
program in order of 7, 3, 11:
Enter as 7
, 3 , 11.
Play Mode Off
Repeat Off
:
:
/Enter/Play Mode
NOTES:
• To cancel program playback, select
“Clear” at step 3 and press ENTER.
• The program is cancelled when you
open the disc tray or turn the power off.
•
In playing back the Video CD with PBC,
you can not set Program playback and
Random playback.
If you input a wrong number,
press CANCEL.
Press / or / to select
4
“Program Playback” and press
ENTER.
The program you selected will
begin to playback in the order set.
To return to normal playback, select
“Play Mode: Off” at step 2 above.
Random playback
Press PLAY MODE in the stop
1
mode.
Press / to select “Random”.
2
Press PLAY.
3
Random playback will start.
Play Mode Off
Repeat Off
Play Mode
Repeat
:
:
/Enter/Play Mode
:
Random
:
/Enter/Play Mode
Off
2C51201AE(42-47) 15/3/03, 11:15 AM43
43
Loading...